Question about Cars & Trucks

Open Question

What does the clutch spring return look like - Cars & Trucks

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Clutch problem the clutch pedal won't return back UP, why ?


indicates no fluid in the system or air in the system
in a hydraulic it requires fluid to make the clutch disengage and also fluid to make the pedal return from the pressure of the pressure plate
if it is a cable clutch, replace the cable as the inner cable is breaking and jamming in the case

Sep 30, 2016 | Cars & Trucks

1 Answer

Where is my clutch pedal return spring located at and where do its attach to???? 2006 volvi? s40 2.4l


It shouldn't use a spring to return the pedal, it uses hydraulic pressure to return the pedal to the rest position. If the clutch pedal isn't returning, you could have an issue with the slave or the master cylinder for the clutch.

Feb 28, 2015 | Cars & Trucks

1 Answer

Is there a diagram of where the clutch return spring is on a 2008 Hyundia Santa Fe?


The clutch don't have spring to return. hydraulic pressure return the pedal. if you pedal go down to the flour and don't return you lost the pressure. First look in the reservoir for fluid. add DOT3 brake fluid and bleed the system. inspect for leak
Good luck

Apr 15, 2014 | 2007 Hyundai Santa Fe Limited

2 Answers

Clutch problem


I would think you have a hydraulic clutch, so there should be a return spring on the pedal or the master cylinder.

Jan 29, 2014 | Subaru Cars & Trucks

1 Answer

Hydrolic clutch pedal sticking


Hi, Look in the foot well (where you normally have you feet) you should see a return spring attached to the clutch pedal, if missing or you can see broken spring you need to buy another spring, you will see parts of broken spring where they fit not a very hard job to replace. Please leave me feedback thanks, Malcolm Campbell.

Feb 16, 2012 | 1983 Nissan 280ZX

1 Answer

Clutch pedal not returning fully on nissan primastar


this car should have a hydraulic clutch check the fluid level in the master cylindar. also there should be a return spring on the clutch fork on the side of the transmission check to make sure this spring is still in place

Nov 18, 2010 | Nissan Minivan Cars & Trucks

2 Answers

Clutch went to floor like nuthing was attached to it... runs fine just seems that the clutch pedal dont work or something it just floppy now...it happened when i was moving it in driveway was fine before...


There is a return spring that lifts the clutch pedal back to the original position. It seems that the clutch return spring has got disconnected. The pedal will do its job of disengaging the engine from the gear box, but will not offer any resistance to the foot and thus give an impression of doing nothing. So, that spring should be set right. For this the clutch housing will have to be opened and the spring reset.

Feb 10, 2010 | 1994 BMW 3 Series

2 Answers

Clutch sticking on 2000 pontiac firebird trans am. clutch comes halfway up but need to pull it up the rest of the way w/my foot.


There is actually a fix for this problem. There is no return spring for the clutch being that it is hydraulic. You need to take the master cylinder out and drill the return line an 1/8th of an inch. The reason why it sticks is because the return line is too small. All the fluid is backed up and once it is cleared, the clutch will return to normal. There is an article in GM High Performance magazine online that has the step by step instructions to fix it. Hope this helps.

Aug 28, 2009 | 2000 Pontiac Firebird

1 Answer

Don't know where my return spring goes on my 71 firebird for the clutch.


You should have a heavy return spring under the dash on the pedal and a lighter one on the clutch linkage with one end hooking beside the rod pushing onto the clutch pivot. (some have a small hole for the spring) (The clutch pivot is the part going into the bell housing holding the bearing) and the other end hooking on something that will keep the pivot and bearing away from the clutch when you are not pushing the clutch pedal.
TIP. When sitting stopped for any length of time with the engine running......(and more important with heavy duty clutches)....put the vehicle in neutral and keep your foot OFF the clutch.

Aug 19, 2009 | Pontiac Firebird Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...