Question about Cars & Trucks

Open Question

How do i remove rear drum on a mazda2 2006 model it has a large bolt with a metal cover around some kind of locking nut do i have to remove it first or can i get a socket to fit over the lot to undo ?

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 24 Answers

SOURCE: 97 Taras sedan SE style rear stut top bolt and nut location.

The top nuts are located from inside of the trunk. If you look behind the material that covers the wheel wells you should find the nuts near the top of the wheel wells.

Posted on Nov 30, 2008

Ad
godspeed808
  • 125 Answers

SOURCE: Wheel locks

heres my site I got those same wheel locks from and also a few others hope this helped:
www.godspeedmotorsportsonline.com
www.ebay.com
peach street auto 18003652341

Posted on Feb 06, 2009

  • 34 Answers

SOURCE: Do I have to remove the large NUT in the middle of

hit it with a big hammer hit on stud side and it will looses up and dont pull that nut

Posted on Aug 12, 2009

  • 270 Answers

SOURCE: How do I remove a locking lug nut from a 96

You're supposed to have a key socket to remove it. There's also removal tool kit. Most tire dealers have the kit and can remove it for you.

Posted on Jan 10, 2010

duane_wong
  • 6826 Answers

SOURCE: the rear drum wont come off as i would expect

Yes, Undo the 32mm nut, first. And, don't get the bearings dirty with dust from the brake drums, or , if you do, replace the inner and outer bearings with new greased up ones.prev.gif next.gif REAR DRUM BRAKES Brake Drums REMOVAL & INSTALLATION CAUTION
Brake linings contain asbestos. Asbestos is a known cancer-causing agent. When working on brakes, remember that the dust which accumulates on the brake parts and/or in the drum contains asbestos. Always wear a protective face covering, such as a painter's mask, when working on the brakes. NEVER blow the dust from the brakes or drum.

  1. Raise the vehicle and support safely.
  2. Remove the wheel and tire assembly.
  3. On vehicles without rear bearing hub, remove the dust cap, cotter pin, nut lock, wheel bearing nut and washer from the spindle. Remove the outer wheel bearing. Remove the drum with the inner wheel bearing from the spindle. If the drum is difficult to remove, remove the plug from the rear of the backing plate and push the self adjuster lever away from the star wheel. Rotate the star wheel to retract the shoes. Remove the grease seal.
  4. If equipped with a rear bearing hub, remove the drum by removing the retainer screws from the drum and pulling the drum from the hub assembly. If the drum is difficult to remove, remove the plug from the rear of the backing plate and push the self adjuster lever away from the star wheel. Rotate the star wheel to retract the shoes. To install:
  5. On vehicles equipped without rear bearing hub, lubricate and install the inner wheel bearing. Install a new grease seal. Install the drum to the spindle. Lubricate and install the outer wheel bearing, washer and nut. Adjust the bearing preload following the procedure outlined in the "Rear Wheel Bearing'' of this section. When the bearing preload is properly set, install the nut lock and a new cotter pin. Install the grease cap.
  6. On vehicles with rear bearing hub, install the brake drum to the hub assembly and install the retaining screws.
  7. Install the wheel and tire assembly. Adjust the rear brakes as required.
  8. Apply the brakes until a firm pedal is obtained, prior to moving the vehicle.

Posted on Jul 12, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you replace the rear wheel hub on a 2003 Kia sedona. All I can find is directions on front not back.


Wheel Bearings

Print
Adjustment

2002-05 Models
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Remove or disconnect the following:

    Rear wheel Brake drum Hub cover Cotter pin Lock nut cover
  3. Adjust the locknut to achieve wheel bearing play of 0.001-0.006 inches (0.025-0.152 mm).
Removal & Installation

2002-05 Models
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Remove or disconnect the following:

    Rear wheel Brake drum Hub cap Cotter pin Lock nut cover Lock nut Wheel bearing retainer washer and the outer wheel bearing Hub assembly Grease seal Inner wheel bearing
  3. Clean and inspect the wheel bearings and races for unusual wear or damage. Replace parts as necessary.
To install:
  1. Pack the wheel bearings with grease for assembly.
  2. Install or connect the following:

    Inner wheel bearing Grease seal Hub assembly Lock nut. Adjust the locknut to achieve wheel bearing play of 0.001-0.006 inches (0.025-0.152 mm). Lock nut cover Cotter pin Hub cap Brake drum Rear wheel

Apr 03, 2015 | 2003 Kia Sedona

1 Answer

I have a 2000 suziki grand vitara and cant furure out how to remove the rear drums


  1. Raise and safely support the vehicle.
  2. Remove the rear wheel(s).
  3. Release the parking brake.
  4. Remove the parking brake lever cover screws and loosen the brake cable locking nut.
  5. Install 2, 8mm bolts into the brake drum holes and uniformly tighten each bolt. Tighten each bolt until the brake drum is removed from the vehicle. If there is difficulty in removing the drum, insert a small tool through the hole in the rear of the backing plate, and hold the automatic adjusting lever away from the adjuster. Using another narrow, flat tool at the same time, reduce the brake shoe adjuster by turning the adjusting wheel.
If the drum is difficult to pull off using the bolts mentioned above, the parking brake is most likely the cause and will have to be adjusted "IN" to prevent drum to shoe contact.


ledsled378_171.jpg

Sep 20, 2011 | 2001 Suzuki Grand Vitara

1 Answer

Do i have to remove the differential housing cover to remove C - clips or can i just unbolt the hubs and remove both lock nuts on the hub because I want to check my rear brakes on a 65 chevy 3/4 ton...


Hi! sensenicht
Are there bolts on the outer hubs. If so removing the axel hub bolts will allow you to pull the axles. You should be able to remove the lock nut, lock washer and adjusting nut (second nut) to remove rear brake hubs and drums. The C-Clips are only used on the half ton and lighter cars. This is called floating axels.
Its important to replace the hub seals on the inside of the drums. A small amount of axel greese will make your brakes not work properly.
InMrFixIt

Jun 25, 2011 | Chevrolet 2500 Cars & Trucks

1 Answer

How to replace rear wheel bearings on a 2000 cougar?


Hi,welcome to fixya.


The rear wheel bearings are not adjustable. If the bearings make noise or become loose, they must be replaced.

Removal & Installation

With Drum Brakes

NOTE The wheel bearings are contained within the wheel hub and must be replaced as an assembly.

  1. Disconnect the negative battery cable.
  2. Raise and safely support the vehicle.
  3. Remove the wheel and tire assembly.
  4. Remove the anti-lock sensor retaining bolt and remove the sensor.
  5. Remove the brake drum retainer and the brake drum.
  6. Remove the hub retaining nut dust cover.
    NOTE Do not use an impact gun to remove the hub retainer nut.


    0996b43f80232353.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Using suitable tools loosen and . . .


    0996b43f80232351.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. . . . remove the hub retaining nut dust cover
  7. Remove the wheel hub retainer nut.

    0996b43f8023234f.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Using suitable tools, loosen and . . .


    0996b43f80232352.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. . . . remove the hub retaining nut
  8. Slide the hub and bearing assembly off of the spindle.

    0996b43f80232350.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Carefully slide the hub and bearing assembly off of the spindle

To install:
  1. Reinstall the hub and bearing assembly to the spindle.
  2. Reinstall the hub retainer nut. Tighten the retainer nut to 170-192 ft. lbs. (230-260 Nm).
    WARNING Do not use an impact gun to tighten the hub retainer nut, otherwise the bearings may be damaged.
  3. Install the hub retaining nut dust cover.
  4. Reinstall the brake drum.
  5. Check the brake shoes for proper adjustment.
  6. Reinstall the anti-lock sensor and the retaining bolt. Tighten the retaining bolt to 7-8 ft. lbs. (9-11 Nm).
  7. Reinstall the wheel and tire assembly. Tighten the wheel nuts to 62 ft. lbs. (85 Nm).
  8. Lower the vehicle until the wheels are supporting the vehicles weight. This will properly load the suspension.
  9. Tighten the spindle-to-control arm bolt to 52-79 ft. lbs. (70-98 Nm).
  10. Tighten the tie rod-to-spindle bolt to 75-102 ft. lbs. (102-135 Nm).
  11. Finish lowering the vehicle.
Road test the vehicle and check for proper operation.
Thank You for using fixya........iluv2fish........Ray........

Jul 16, 2010 | 2000 Mercury Cougar

2 Answers

How to remove broken lug on 98 Elantra. Can't get the disc off that lugs press into. Already have removed 4 bolts/nuts that secure this disc to the brake rotor. Also have already removed large castle nut...


As far as I can determine, your Elantra has standard rear disc brakes.
The lugs should be attached to the hub, which is attached to the axle. The Disc or Rotor (they're one and the same) slip onto the hub. Oftentimes the disc will seize on the hub from rust. You need to spray the center hole, where the disc goes over the hub, with spray penetrating oil. Also spray the lug stud holes. Then take a (dead blow )hammer and hit the disc around its perimeter. It should then come loose.
The broken stud can then be taken out by hitting the front of the stud with a hammer. You may want to spray the back of the stud where it seats on the hub before taking the hammer to it. Place the new stud through the rear and make sure it's seated correctly.
Clean all parts with brake parts cleaner. The lug studs should not have any lubrication on them.
You have to re-set that "large castle nut" that was removed to its proper Preload Torque. I do not know that spec, but you need to find it out, and how it's done.
Suggest you purchase a Repair Manual for your vehicle(s). It really is the best tool you can get.

Aug 11, 2009 | 1998 Hyundai Elantra

2 Answers

How do I remove the rear brake drum on the 90 rocky to remove and replace the lug bolts?


after removing the wheels, it should just slide off. If you have a ridge on your drums this might not be possible. You can try to install two bolts into the small bolt holes on the drum. Turn these bolts together as much as possible and it will force the drum off. Like I said though, if you have a ridge on your drums you will have to back off the star adjuster located inside the brake drums. To do this, there is a small inspection hole on the back side of the drum. There should be a small rubber cover shaped like a large horse pill. Oval in shape. Remove this and you will have access to the adjuster. Using a flat blade screwdriver, pry the gear shaped wheel until the shoes of the brakes are adjusted in far enough to bypass the ridge on the drums. This combined with the two bolts should release the drum from the axle. Good luck.

Jun 13, 2009 | 1990 Daihatsu Rocky

1 Answer

Removing valve cover toyota camry


You need to pull the plug wires up and out of their tubes. They can get stuck so twist them left and right to help loosen them first. The plugs are in the tubes. Use a 5/8 plug socket to remove them. Around the tubes you will see large flat nuts. You will need to remove all 4 of these. Also on the top timing belt cover there are 2 10mm head bolts you will need to back out at least 1/2 way for 2 reasons. 1 to free up the wire harness that crosses there and the bolts extend over the valve cover blocking its removal. Then with a screwdriver pry up the metal washers and rubber seals that were under the large flat nuts. The pcv valve needs to be pried out of the valve cover in the center and then the cover will come off.
Reverse to install.

Mar 21, 2009 | 1994 Toyota Camry

2 Answers

I need to remove the brake drum on a 1976 gmc sierra 25


Soak it with generous amounts penetrating oil around the lugs and let it sit for a while and soak it again and hit it with a bigger hammer. There arent any hidden bolts they are just stubborn sometimes (most of the time).

Jan 29, 2009 | 2004 GMC Sierra 2500

1 Answer

94 landcruiser brakes


Rear DRUM instructions are first If you would Like Pictures and all They Must Be Emailed as TOO LARGE For FixYa's Format im at aol.com
Just use my Knickname@ and let me know where to send.


  1. Raise and support rear of vehicle, then remove wheel and tire assembly.
  2. Remove brake drum. If brake drum cannot be removed easily, insert a suitable screwdriver through hole in backing plate, then push adjuster lever away from adjuster and back of adjustment tension.
  3. Remove tension spring, using a suitable tool, then remove rear shoe hold-down spring and pin. Remove rear brake shoe and anchor spring, Fig. 7.
    1. On Land Cruiser models, remove front hold-down spring using a suitable tool, then disconnect the parking brake cable from the parking brake bellcrank, Fig. 7.
    2. On Pickup, 4Runner, 4WD T100 and 4WD Tacoma models, remove front shoe hold-down spring and pin, using a suitable tool, then disconnect No. 1 parking brake cable from No. 3 parking brake bellcrank.
    3. On 2WD T100 models, proceed as follows:
      1. Remove E-ring, then automatic adjusting lever and C-washer, then parking brake lever. Disconnect brake line from wheel cylinder using a suitable container to catch fluid.
      2. Remove wheel cylinder. Remove following parts from wheel cylinder: two boots, two pistons, two pistons cups and spring.
    1. On models except 2WD T100, remove front brake with strut, then disconnect parking brake cable from front shoe. Remove parking brake cable No. 2.
    2. Remove adjusting lever spring, then the adjuster from front shoe.
    Inspection
    1. Measure brake drum inside diameter. Inside diameter should be 11.61 inches,
      1. Measure brake shoe lining thickness, Fig. 3. Minimum thickness should be .04 inch on models except on T100 models and .039 inch on T100 models.
      2. Inspect brake lining and drum for proper contact and replace drum or shoes as necessary.
      3. Inspect wheel cylinder for corrosion or damage.
      4. Inspect backing plate for wear or damage.
      5. Inspect bellcrank components for bending, wear or damage.
      6. Apply a suitable lubricant to backing plate contact areas.
      Installation
      1. On 2WD T100 models, proceed as follows:
        1. Apply lithium soap base glycol grease to piston cups, pistons and boots.
        2. Assemble and install wheel cylinder.
        3. Connect brake line to cylinder.
      1. Apply high temperature grease to following parts:
      1. Apply a suitable lubricant to adjuster bolt threads and end.
      2. Assemble adjuster to lever, then install adjuster lever spring.
      3. On Land Cruiser models, install parking brake lever cable to parking brake shoe, then attach cable to bellcrank.
      4. On Pickup, 4Runner, 4WD T100 and 4WD Tacoma models, install No. 1 parking brake cable to parking brake lever shoe, then attach the other side of cable to No. 3 bellcrank.
      5. Position front shoe in place with end of shoe inserted into piston, then install shoe hold-down spring and pin using a suitable tool.
      6. Assemble anchor spring to front and rear shoe, then install rear shoe with end inserted in piston.
      7. Install rear shoe hold-down spring and pin, then the tension spring.
      8. If necessary, adjust bellcrank as follows:
        1. Lightly pull bellcrank in direction "A", Fig. 8, until there is no slack in part "B".
            1. Rotate adjusting bolt until dimension "C" is .016-.031 inch.
            2. Lock adjusting bolt with locknut, when connect parking brake cable to bellcrank.
            3. Install tension spring.
          1. Ensure proper parking brake travel.
          2. Pull adjusting lever cable upward, then release and ensure adjusting bolt rotates. If bolt does not rotate, check for improper installation of rear brakes.
          3. Adjust strut to shortest possible length, then install drum.
          4. Pull parking brake lever fully upward. Repeat process several times.
            1. Remove drum, then check for proper clearance, Fig. 4. Clearance should be .024 inch. If clearance is not as specified, check parking brake system.
            2. Install brake drum, then bleed and refill brake system.
            3. Install wheel and tire assembly, then lower vehicle.

FRONT ROTORS & PADS
  1. Remove caliper.
  2. Remove cap and snap ring, Fig. 10, then remove cone washers with tapered punch.
  3. Insert suitable length bolts into flange bolt holes, then tighten bolts evenly and remove flanges.
  4. Remove free wheel hub cover and snap ring, then remove nut, spring washer and cone washer with suitable tapered punch.
  5. Remove free wheel hub body and gasket.
  6. Remove locknut, lock washer and adjusting nut.
  7. Remove axle hub and brake disc as an assembly.
  8. Remove oil seal and inner bearing from hub.
  9. Reverse procedure to install. Torque adjusting nut to 43 ft. lbs., then back off nut. Torque nut to 18 ft. lbs. Using spring scale attached to hub bolt, check that preload is 1.4-12.6. Install lockwasher and locknut, if equipped. Torque locknut to 35 ft. lbs., and recheck preload. Secure lockwasher by bending one tab inward and one tab outward.
  1. Raise and support front of vehicle, then remove tire and wheel assembly.
  2. Remove clip and hole pins, Fig. 9.
  3. Remove anti-rattle spring and shim(s) if equipped, then remove brake pads.
  4. Lubricate caliper housing with suitable brake grease at pad contact points.
  5. Reverse procedure to install.

Jan 28, 2009 | 1994 Toyota Land Cruiser

1 Answer

1990 626 Mazda rear drum brakes


This "large nut" you are talking about is holding a drum. Usually over him is a cover. Use big screwdriver and hammer to remove cover, gently strike from all sides, and when you remove it you will approach to a big nut. Pay attention that under the drum is a whole breaks sistem. After you remove the nut gently strike from the rear, from all sides (left, right, up and down). Drum will fall off.

Sep 28, 2008 | 1990 Mazda 626

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...