Question about 2000 Oldsmobile Bravada

Open Question

How to remove rear/upper inside trim by back hatch. I have washer fluid running out of the trim. Sorry, 2000 olds Bravada.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

jgwhomeequip
  • 1902 Answers

SOURCE: rear hatch window installation

To install, get about 1/4" cord(rope will work), put the seal on the window, put the cord in the SEAL, where it seals to the CAB, have someone hold the window up to the back of the cab for you. You want the cord to meet at the top in the center. Try and get the window on the frame as much at the top as possible, then start pulling the cord. Be careful, a medium sized flat screwdriver will help too. The object is to get the cord to pull the seal around the frame of the window for you without using the screwdriver. You can use the screwdriver to help, but careful, it'll rip the seal very easily

When I worked in a bodyshop, we would grease up the cord with white grease, but I've done it without it. You just have to be real careful.

Posted on Feb 07, 2009

  • 166 Answers

SOURCE: 96 Bravada, tailgate and rear glass won't open

its a linkage problem . you need to remove the door panel to repair

Posted on Jun 12, 2009

  • 14036 Answers

SOURCE: 2000 olds bravada. headlights and taillamps stay

PROBLEM COULD BE THE AUTOMATIC LAMP CONTROL RELAY OR FAULT IN THE BODY CONTROL MODULE.

Posted on May 05, 2010

  • 2428 Answers

SOURCE: "Oldsmobile Bravada: I own a 1992 Olds Bravada.

Did you try bending the metal arm going to the wiper blade so there is enough pressure to make the blade contact the window better. I just did one two days ago and if im reading what what you are saying right its is the same problem and it fixed it

Posted on Jan 15, 2011

mc1bean
  • 3053 Answers

SOURCE: How to remove the radiator

You have to use pri bar to hold against when screwing off. You put pri-bar against section you are turning as to not have fan to turn while unscrewing

Posted on May 08, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Where do I add washer fluid for rear window wiper on a 2000 blazer


Open the hatch and look for the fill cap along the sides .

Oct 23, 2015 | Cars & Trucks

1 Answer

How do i remove the boot trim on a rover 25


You don't remove the boot trim.
The pipe runs through the black plastic rubber tubing, top left of the boot hatch, and then runs to the base of the wiper.
Pull off the black plastic cover, at the bottom of the wiper arm, and try the rear washer again.
If nothing comes out, then the prob is most likely is that the water tube has snapped, inside the black rubber tubing at the top of the hatch.
Good luck!

Feb 08, 2013 | 2004 Rover 25 1.4

1 Answer

How does one remove the inside plastic panel / molding on the back hatch?


usally,if there is a pull handle.2screws hold that on and then you can pull or gently pry off panel

Mar 11, 2012 | Cars & Trucks

1 Answer

Rear hatch latch is stuck.


The clip that retains the release rod in the rear hatch assy. Breaks and allows the rod to fall off. You need to remove the handle from the inside of the hatch. You can pick the plugs out of the handle with a small screwdriver with a small screwdriver, and then remove the handle with a 10mm socket. After removing the handle you should be able to pull back the plastic and look inside with a flash light. Locate the rod that runs to the side that is inop. You should be able to reach in with a screw driver and pull it toward you to release it. Make sure you have already released the working side so it will open for you. Once the hatch is open, you can continue to remove the rest of the plastic trim on the hatch with a phillips head screw driver. After the trim is removed, you will need to re-attach the rod to the mechanism with the clip on the mechanism. If the clip is broken you will need to obtain a new one from a local dealer, or parts supplier. If you have to order a clip, attach a piece of wire, or string to the rod so you can release it from the inside while you are waiting for the new retainer.

Jan 17, 2010 | 2001 Chevrolet Astro

1 Answer

How to get to the stock subwoofer, in 200 eddie bauer expedition


It should be mounted on the passenger back. you will have to remove the rear quarter interior panel, The trim where the hatch locks and around the trim where the hatch meets the rear. once the trim is removed you can access the sub, it is bolted to the car and plugs into the factory amp, which is located right in front of the sub. After taking the bolts out, the sub will come out.

Dec 26, 2009 | 2000 Ford Expedition

1 Answer

I need to replace my dented rear hatch on my 1994 camry wagon.where does the wireing for the lights and wipers disconnect-- i do not want to just cut it at the junk yard and retape it. also the same for...


I don't know about the washer fluid... but the wires should disconnect at your wiper motor and lights.. the other end of the wires are going to be hidden inside the trim on the driver's side inside the trunk. All the wires are going to run from a harness behind the trim of the trunk, up behind your roof cover, out a tiny hole through a rubber seal (the washer fluid hose should run through this seal as well) and into the hatch and back behind the trim... You'll need to remove a lot of trim to get to the wires. I did this with a focus and the trim removal took a good 30-45 mins. hardest part is finding all the screws and the clip points... T
As for the lock, you should be able to see two bolts on the inside of the hatch holding the lock assembly down...

Aug 14, 2009 | 1994 Toyota Camry

1 Answer

Rear windshield wiper connection


You need to open the rear glass from the rear hatch. Look inside where the glass latches to the rear hatch. There is a Phillips head screw that connects the rear inner plastic panel to the rear hatch, remove this screw. Now, in the strap that you use to pull the rear hatch down, there is a torques head screw, that holds this strap to the rear hatch, you need to remove this screw.
Start at one of the outer corners of the inner plastic panel and pull the panel away from the hatch. You will see the upper wiper motor in the right hand corner of the hatch. ther is one connector that is easy to see, you have to pull up on a plastic clip to remove this connector. Look for the rubber hose for the windshield washer fluid, it may be cracked or fallen off the plastic nozzle to the outside of the rear door.

Please the hose back on or replace the hose if it's cracked or damaged by the wiper motor. To install just follow the procedure in revers.
Good luck and hope i made some sense. Keep me posted, be glad to help out.

May 29, 2009 | 1999 Chevrolet Blazer

1 Answer

2000 Honda Odyssey rear wiper motor replacement


You are probably correct in thinking its the wiper motor. You can do this but you will need to remove all the interior trim from the rear hatch first. Get a trim clip removal tool at a parts store...it will work much better than just a flat blade screwdriver. You'll have to remove the trim panels starting in order from the top of the door, then the left rear window side trim, then right rear window side trim, then the grab handle, and finally the main rear hatch trim panel. Once inside, removing and replacing the rear wiper motor is easy. You'll start by lifting the cover on the wiper arm retention nut. Remove this nut to get the wiper arm off, then remove the nut under neath which is the motor shaft mounting nut. Now, back inside to remove the other 3 motor mounting bolts. Don't forget to disconnect the connector for the motor wires. Reverse steps to replace.

Mar 29, 2009 | 2000 Honda Odyssey

1 Answer

2000 vw golf how do I remove back hatch liner to


in each of those "holes" which are flanking the center hatch there is a screw in the bottom. remove those screws. then its pretty simple, yank out. the connectors to the actual hatch are in there really tight, so its kinda scarey on how much force you need to pull out. but it will just pop right out. be careful and keep a watchful eye out to where it connects to upper trim piece, it bends pretty easy... trust me i know

Mar 06, 2009 | 2000 Volkswagen Golf

Not finding what you are looking for?
2000 Oldsmobile Bravada Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...