Question about 1996 Oldsmobile Bravada

Open Question

Remove rear panel in 96 bravda

REAR GATE WON'T OMEN

Posted by on

Ad

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
Brian032472
  • 150 Answers

SOURCE: remove right rear door panel

  1. Remove the rear door power window/power door lock switch
  2. Remove the door handle bezel. Remove the door trim panel screw located behind the door handle bezel.
  3. Remove the door trim panel screws located by the armrest handle.
  4. Remove the door trim panel using J 38778.
  5. Disconnect the electrical connectors.
  6. Remove the door trim panel from the door.
INSTALLATION PROCEDURE

IMPORTANT: Discard the old door trim panel retainers and replace with new retainers before installing the trim panel

  1. Install new trim panel retainers to the rear door trim panel.
  2. Connect the electrical connectors.
  3. Align the door trim panel retainers to the door.
  4. Press the door trim panel at the retainer locations until the retainers are fully seated.
  5. Install the trim panel screws. Tighten Tighten the door trim panel screws to 2 N.m(18 lb in) .
  6. Install the power window/power door lock switch


Posted on Nov 04, 2008

Ad
  • 295 Answers

SOURCE: how remove the rear inside door panel on a 2001 oldmobile aurora

The inner door panel is held in by clips and screw.
Look at the door near the door handle there should be screws holding it in and along the outer edge of the door. Once loose, and the door handle removed or the arm rest removed. The door panel then prys out , because of the clips that hold it on. Then pops out by applying pressure to the panel upward to the top of the door. The clips always break because of the design and plastic.

Good luck

Posted on Mar 21, 2009

  • 1986 Answers

SOURCE: rear door panel removal

You'll need to remove screws that are by the door handle, arm rest, under door and side of door and then gently pull back on the panel as there will also be retaining clips attached and you don't want to break them. If needed, you can pull back the weather seal (can't reuse it, but it's not that important) and you will be able to access everything inside the door

Posted on Aug 14, 2009

claudeinmo
  • 9098 Answers

SOURCE: Why do I see a rear access open and a gate ajar warning on insument panel, even though it is locked?

[SOLVED] False Gate Ajar/Rear Access Open warnings: follow up post ...

forums.trailvoy.com > ... > 02-09 General Tech Q&A > General

Dec 28, 2009 - 4 posts - ?2 authors
[SOLVED] False Gate Ajar/Rear Access Open warnings: follow up post General. ...2002 Chevy TrailBlazer LTZ ... In cold weather, I have a constant "gate ajar" warninguntil the ... Should I try to unhook/rehook the connections to the BCM? ... You might confirm it by starting the vehicle cold, see that you have ... Annoying tailgate ajar won't quit going off on 04 gmc ...
11 posts
Feb 4, 2010
Rear latch assembly not functioning on Lift Gate
10 posts
Oct 12, 2009
Gate Ajar - turning off
5 posts
Jul 1, 2007
passenger door ajar
5 posts
Nov 9, 2005
More results from forums.trailvoy.com

Rear access door ajar - false signal - Fixya

www.fixya.com/cars/t22610885-rear_access_door_ajar_false_signal

Posted on Feb 03, 2016

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I replace a burned out rear backup light


Open the liftgate. Remove the liftgate applique. Refer to Liftgate Applique Replacement in Body Rear End. Remove the back up lamp socket (1) from the liftgate applique by turning the socket (1) counterclockwise. Remove the back up lamp bulb from the socket.
Lift gate Applique Replacement
Remove the lift gate trim panel. Refer to Lift gate Trim Panel Replacement .
1
Lift gate Applique Nuts (Qty: 5)
Tip
Disconnect the electrical connector.
Tighten
10 N?·m (89 lb in)
2
Lift gate Applique

+zsnqmiiiiiiiiik+gomverererererercry0ddwiiiiiiiiiiilogstkiiiiiiiiiiiioasskymiiiiiiiiiiuisskymiiiiiiiiiiiisycxmiiiiiiiiiiiis6cxmqiiiiiiiiiiig4cxiriyiiiiiiiiii4ixiriyiiiiiiiiiiiizileyiiiiiiiiiiiizoleyoiiiiiiiiiiidgleisjiiiiiiiiiilileisjiiiiiiiiiiiilmgstiiiiiiiiiiiilogstkiiiiiiiiiiiioasskymiiiiiiiiiiuisskymiiiiiiiiiiiisycxmiiiiiiiiiiiis6cxmqiiiiiiiiiiig4cxiriyiiiiiiiiii4ixiriyiiiiiiiiiiiizileyiiiiiiiiiiiizoleyoiiiiiiiiiiidgleisjiiiiiiiiiilileisjiiiiiiiiiiiilmgstiiiiiiiiiiiilogstkiiiiiiiiiiiioasskymiiiiiiiiiiuisskymiiiiiiiiiiiisycxmiiiiiiiiiiiis6cxmqiiiiiiiiiiig4cxiriyiiiiiiiiii4ixiriyiiiiiiiiiiiizileyiiiiiiiiiiiizoleyoiiiiiiiiiiidgleisjiiiiiiiiiilileisjiiiiiiiiiiiilmgstiiiiiiiiiiiilogstkiiiiiiiiiiiioasskymiiiiiiiiiiuisskymiiiiiiiiiiiisycxmiiiiiiiiiiiis6cxmqiiiiiiiiiiig4cxiriyiiiiiiiiii4ixiriyiiiiiiiiiiiizileyiiiiiiiiiiiizoleyoiiiiiiiiiiidgleisjiiiiiiiiiilileisjiiiiiiiiiiiilmgstiiiiiiiiiiiilogstkiiiiiiiiiiiioasskymiiiiiiiiiiuisskymiiiiiiiiiiiisycxmiiiiiiiiiiiis6cxmqiiiiiiiiiiig4a+7c+f8dgdgunyxjdkcaaaaasuvork5cyii=

May 10, 2016 | 2004 Cadillac SRX

2 Answers

Gate light on dash will not go off also dome light stays on rear lift door is not jarred


Replace the gate latch. Open the gate, remove the top panel first, it pops off. Remove the bottom, 2 to 4 screws to remove, then it pops off. This gives you access to remove the latch.

Feb 13, 2015 | 2011 Jeep Liberty

1 Answer

2009 Kia Rondo rear gate is not opening. I have power in the fuse panel in the passenger compartment


remove rear panel from gate and check for power, no power trace back from there, (poss break where it goes through from gate to body).

Feb 12, 2015 | Kia Rio Cars & Trucks

1 Answer

Rear sensor


located in the latch you have to remove the back door panel or you can remove the little door panel in the rear to disconnect it so that the light on the dash goes out or replace the latch

May 05, 2014 | 2009 Dodge Journey

2 Answers

2004 gmc envoy window won't go up rear wiper obstruction


I know this question is old, but I am responding so others with the same problem can see. I wired the Rear Window Motor Park Signal wire and the Rear Window Motor Speed Signal wire together and it completely bypassed the rear wiper motor. Now the window goes up and down. This doesn't fix the rear wiper motor, but you will be able to have access to it now that the window is out of the way

I made and album to show.

http://imgur.com/a/q3vww

Jun 30, 2012 | 2004 GMC Envoy

2 Answers

Rear Windshield Wiper Motor


look closely/carefully for recessed screws. Most are usually pop on/ pop off types. Pull/ pry gently.

Jul 17, 2009 | 1998 GMC Jimmy

2 Answers

Back door wont unlock


I have a 1999 Chrysler T&C 3.8 liter like yours and it sounds
like you are having the same the same problem I had.
Every time you hit the door unlock or lock button, it made a loud
buzz like you just missed a question on a game show. ;-)

It turned out the problem was the rear lift gate lock actuator. The part costs
about $40 from the dealer if I can recall correctly.

The repair involves: 1st removing the middle and rear seats to get
access from the inside to the rear gate
(obviously you will have to remove the seats from the side doors
since the rear gate won't open yet)

Remove the plastic inside rear gate panel and molding (phillips screws)
Once you remove the panel, you may see a way to manually
open the rear gate. As I recall, I think there was a access opening
covered from the inside with a black weather/insulation tape.
Carefully removing this out of the way gave access to a way to
manually open the gate, making the rest of the work easy.

Remove the electrical connector and the mounting bolts
to remove from the actuator. It is attached to the inside
rear gate with 2 or 3 bolts (10 mm?)

Remove the old one and replace the part, then put it all back
together, make sure you reconnect the electrical connector

Takes about an hour for the whole job (max)

Hope this helps,

Wes

May 03, 2009 | 1999 Chrysler Town & Country

1 Answer

Rear wiper motor


raise up the tail gate . remove the phillip screws holding the handle or pull down strap.remove all other screws holding the rear plastic tail gate panel in place than start in one corner try to pull down on the plastic panel as it is also held in place with push style plastic clips.you can use a straight blade screw driver to start releaseing the clips.once you have the panel off you have done the hard part/ just unbolt the wiper motor and reassemble.
good luck chris

Mar 22, 2009 | 1993 Dodge Caravan

1 Answer

Chevy blazer 2w drive 2 door-rear gate wont open


you will need to try to remove the rear door panel on the tail gate or pry it away its not easy because of hidden screws the manually pull the linkage

Aug 16, 2008 | 2002 Chevrolet Blazer

Not finding what you are looking for?
1996 Oldsmobile Bravada Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8572 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...