Question about Cars & Trucks

Open Question

Most controls on led panel don't work

How do I fix the control panel, most buttons don't work only time set, temp set, no green light by program set and on switch doesn't stay on can I open bottom and spray with contact cleaner

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 7 Answers

SOURCE: Steering wheel lamps do not work (radio controls, temp, cruise)

The lights on the steering wheel are in the switches. To fix the lights, the whole switch needs to be replaced. Same thing goes for the Tempature Controls and radio. Overall, I think it would be very expensive to replace all of the switches to get the lights working. I have the same vehicle, and almost all of the lights are out.

I think the lights behind the gage controls are replaceable, although you still have to rip out most of the dash to get to them.

I have the auto-sense wipers, so I was leaving the wipers on all the time, and the would only work when needed. The bad part I finally found out about this was that while the wiper switch is on (even though they were not wiping), it caused all of the dash lights, switch lights and rear parking light to be on. I think this alone significantly cut down on the life of the bulb.

For now, I am just living without the lights. The temperature control is very expensive (just the part alone).

You can usually find the best price for these things at http://www.rockauto.com

Posted on Feb 22, 2009

dr_greg
  • 192 Answers

SOURCE: 98 honda accord A/c panel lights went off. Now only blower works.

you are going to need to replace the climate control panel...

Posted on Apr 05, 2009

ghost4548
  • 776 Answers

SOURCE: Program factory remote keyless entry: 2003 Hyundai XG350

The procedures you list require the Hyundai Keyless Remote programming module, which you don't have. This module is proprietary - only Hyundai Dealerships have it. There is a 10 pin connector under the dash (next to the DLC - Data Link Connector) which is used to connect the Keyless Remote Programming Module. This module has two switch positions "Ready" and "SAVE". When the switch is place in the 'SAVE" position, that's when the keyless remotes are activated to send their 'codes' to the Electronic Time and Control System (ETACS). The module's switch is then set to "Ready" and the remote is tested to see if it works properly.

Posted on May 27, 2009

ghost4548
  • 776 Answers

SOURCE: Program factory remote keyless entry 2003 Hyundai XG350

I've informed you of what you need to do. Take the veh into a Hyundai Service Center - let them program the remotes.

Posted on May 31, 2009

  • 1 Answer

SOURCE: heater temp control not working

We had the same problem in our 98 GMC Jimmy. Was blowing hot air everywher with everything shut off & air conditioning would not work. We found out it was the Blend Dood Actuator, it is located behind the glovebox. We purchased one on EBay & replaced it and are back on track again. Good luck!

Posted on Sep 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Climate control on rover 45 diesel 2004


normally the climate control unit itself which is part of the display panel inside

Jan 14, 2014 | Cars & Trucks

1 Answer

DODGE CARAVAN FLASHING LIGHTS A/C AND RECIRC


On the left side of the A\C control panel hold down the top and bottoms buttons with the engine running and at full operating temperature, the blower speed on high, the mode set to vent, and the temp lever(s) set to full cold. When the lights on the panel come on solid and then start flashing release buttons. It will take about 2 minutes or less for it to calibrate. when the top left button is flashing you are done. Press that button once or restart van all function should be normal.

Jul 26, 2012 | 1998 Dodge Caravan

1 Answer

The lights controls of rear wiper switch is flasher


My 97 Voyager has done the same thing. It was control panel programing, the following instructions is how to program your control panel: 1) SET BLOWER ON HIGH 2) SET MODE TO PANEL 3) SET TEMP TO COLD 4) PRESS WASH AND REAR WIPER TOGATHER AND HOLD FOR 5 SEC. IT WILL GO THROUGH A SERIES OF FLASHING, WHEN DONE THE REAR WIPER SHOULD BE THE ONLY ONE FLASHING PRESS REAR WIPER TO EXIT. DO THIS WITH VAN RUNNING. This worked for my 1997 Voyager. I hope it works for yours.

Jan 24, 2011 | 1998 Plymouth Voyager

1 Answer

This problem is on a 1998 740iL. When I press the steering wheel cruise control activator - the green indicator light comes on but when I press the "set" (+) button it does not engage and the car does not...


my BMW 740i has a problem with the cruise control.
The cruise control will work for about 20 miles and then quit working and will not work again.

May 17, 2010 | Cars & Trucks

1 Answer

96 grand caravan passenger side heat problem. There is a dual temp control, it works properly for the drivers side but the passenger side always blows HOT no matter what the temp control is set. The...


The wire on the back of the control is most likely broken, I had the opposite (drivers side allways cold) I dissconnected the solid light green wire and now have hot air all the time, I disconnect it in the summer for cool air, the part is very expensive, $70.00 at a salvage yard!

Jan 08, 2010 | 1996 Dodge Grand Caravan

2 Answers

Blinking panel lights


To Calibrate , start and warm engine to normal operating temp. with engine idling turn blower switch to high, turn mode switch to panel, open all outlets, move temp lever to full cold.
press and hold rear wash and rear wiper buttons simultaneously for 5 seconds (untill all leds illuminate.) all leds should light up for 5 seconds, rear wiper and intermittent rear wiper button leds will flash alternatly during calibration... after 60 seconds if only rear wiper button led is flashing, cal. is complete

Jun 18, 2009 | 1998 Plymouth Voyager

1 Answer

98 honda accord A/c panel lights went off. Now only blower works.


you are going to need to replace the climate control panel...

Apr 05, 2009 | 1998 Honda Accord

2 Answers

Replaced battery,now rear wiper control lites are flashing.


The procedure for re-setting the HVAC control panel on a 1998 Dodge Grand Caravan follows:
With ignition on but not running
1. turn knob to air vents
2. turn fan knob to ON
3. temperature setting on COLD (2X) {I have dual temp controls}
4. hold top(rear wiper) and bottom (rear wiper with wash) buttons pressing down together until all the buttons cycle through (this will require 1 to 2 minutes of continuous pressing)
Hopefully, this also applies to 1997 version. I learned this from a very helpful local Dodge service adviser

Jan 21, 2009 | 1997 Dodge Caravan

3 Answers

Focus remote key fob not working


this info would cost you £30.+ at ford Radio Frequency Programming Instructions:
  • Insert the ignition key and turn from position II (Ignition) to position 0 (All off) and back four times within three seconds.
  • Remove the ignition key. The locking control system is now in "learn mode" for the next 20 seconds and the red warning system LED (By the clock) stays on continuously to indicate this.
  • During the 20 seconds press one of the transmitter buttons. The remotes signal and code number is learned by the locking module and is indicated by flashing the warning system LED.
  • Wait until learn mode times out (20 seconds) or switch the ignition back to ON.nfrared Programming Instructions:
  • Put your key into the ignition and turn to position 1 (Radio). After approximately 10 seconds the red alarm control LED (next to the clock) should illuminate. As soon as it comes on remove the key from the ignition - the LED should remain lit.
  • Point the remote's "eye" at one of the front door sensors and press the rear button until the light on the transmitter illuminates (Keep the button pressed)
  • With the rear button held in press the front button 4 times then release both at the same time. The control lights in both clock and fob will flash 4 times to indicate programming complete.
  • Turn the ignition back on to exit programming mode

Nov 28, 2008 | 2000 Ford Focus

2 Answers

Cruse controll


Pull up on the brake pedal. If that does not work check your brake light bulbs (LED brake lights will also keep your cruise control form working). Finally check all of the fuses. This system needs at least 3 different fuses to work properly.

Aug 05, 2008 | 1998 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...