Question about Jaguar Cars & Trucks
It does , but it comes in the fuel pump casing , not on the Injectors tube
Posted on Aug 16, 2017
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
the fuel pressure regulator is on the end of the fuel rail it is held on by a torx screw relieve the fuel pressure using the schrader valve on the fuel rail remove regulator holding screw and replace new regulator be carful not to damage o-rings on new regulator
Posted on Nov 02, 2008
Is it the 3400 v6 or the 2.2l four cylinder? If it the v6 then what you have to do is first know where it is. It located on the end of your fuel rail on the driver side of the car. There will be a plastic hose coming off the top of the regulator, unplug it. You then have to undo your fuel line that runs into the bottom of the regulator. You have to use a wrench to get it off, not sure what size it is. Once you undo the fuel line the next step is to unbolt it from the fuel rail. There will be two screws that run in the side of the fuel pressure regulator that are facing the driver side of the car and are threaded in towards the passenger side of the car, just undo those two screws and the regulator should come off. Just repeat the process backwards to put it back on.
Posted on Jan 09, 2009
another engineers wet dream. think of it this way . what is normally in the intake when the engine is running.. answer vacume, hence the regulator gets its vacume without a hose connected to it as its already in a full time vacume chamber.no hose required . ps be carefull to seat the regulator and o rings securely into the housing befor you reattach the secureing metal clip.
good luck chris
Posted on Mar 23, 2009
SOURCE: Jaguar x type 2004 front bumper
Front bumper removal is quite easy. To start with there is 4 10mm bolts one by each headlamp ( with the bonnet open) remov them. There is 3 T30 screws that hold the under tray to the subframe and there is also a small corner trim that is on the bumper side of the front wheel arch here is 3 T30 screws holding them on on each side. Finally remove the front wheel arch lining so you can get acsess to the inside of the bumper. You will then see a 10mm bolt towards the top of the bumper that is reversed to you. Remove then the bumper should then just pull away.
Becareful not to damage the fog lamp harness upon removal
Posted on Apr 24, 2010
FULLY PRESS THE BUTTON THAT SAYS MODE AND THE CLOCK WILL FLASH PUT 24HR AND TYPE IN THE TIME THEN PRESS MODE AND WILL RESET
Posted on May 01, 2010
Tips for a great answer:
May 20, 2017 | Jaguar X-Type Cars & Trucks
Apr 03, 2016 | Jaguar Cars & Trucks
May 22, 2015 | 2000 Jaguar S-Type
Mar 18, 2014 | 2001 Jaguar S-Type
Jul 03, 2012 | Jaguar XJ6 Cars & Trucks
Jul 03, 2012 | 1994 Jaguar XJ12
May 18, 2012 | 2000 Jaguar S-Type
Hello.I presume you mean P2296 which will be the fuel pressure regulator 2 Control Circuit High
Possible Causes are:
Oct 09, 2011 | 2004 Jaguar X-Type
May 11, 2010 | 2002 Jaguar X-Type
Jul 04, 2009 | 2000 Jaguar S-Type
Jan 26, 2018 | Jaguar Cars & Trucks
45 people viewed this question
Usually answered in minutes!
Step 2: Please assign your manual to a product: