Question about Chrysler Cars & Trucks

1 Answer

Where is the fuel injector rail located, in order to hook up pressure guage on '99 Chrysler lhs

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Chrysler Master
  • 14,411 Answers

1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

I am looking to replace a leaking fuel injector rail for 1993 fifth ave chrysler new yorker p/n 4554109

The rail is most likely not the problem, the fuel injector "O" ring seals are likely the problem in the rail.

Mar 04, 2017 | Chrysler Fifth Avenue Cars & Trucks

2 Answers

1999 chrysler 3.5 lhs fuel not going to injectors

Then your fuel pump is not working, or your fuel filter is blocked. You will probably have to check your fuel pump circuit if you have no fuel pressure in the fuel rail, where the injectors sit. There is a fuse for the pump, usually in the under hood fuse/relay block. That is probably also where the fuel pump relay is located. You should hear or feel this relay click when the ignition key is cycled from off to on. Also, when the key is turned to on, you should hear the fuel pump in the gas tank turn on for about 2 seconds. This will put the pressure in the gas in the fuel rail, for starting the engine. If you don't hear the pump turn on for that 2 second period, it is probably a bad fuel pump. But know the fuse is good first.

Sep 25, 2015 | Chrysler Cars & Trucks

1 Answer

Where is the fuel pressure regulator located on a 99 regal gs supercharged

should be on the fuel rail, take the plastic engine cover off and you should see the injector rails on either side of the supercharger, got to be real close to the line towards the firewall

Nov 10, 2013 | Buick Regal Cars & Trucks

1 Answer

99 Chrysler Sebring just died like it was out of gas but the tank is half full.

Have you checked base fuel pressure at the injector rail with a gauge ?
The fuel pump or one of the relays may have failed.

May 18, 2013 | Cars & Trucks

1 Answer

Won't start,has spark, has fuel

Are you sure the injectors are spraying if the pressure is zero ?
Have you checked the fuel pressure regulator ?
Are the spark plugs dry ?

Dec 12, 2012 | 1998 Cadillac DeVille

1 Answer

1998 dodge dakota will not start?? the sending unit the only thing sending fuel to the fuel injectors? Thanks

There is a fuel pump in the gas tank that pumps gas up to the fuel rail on the engine going through a fuel filter along the way(usually on the inside of the frame rail drivers side). The sending unit has more to do with telling your fuel guage what level of fuel is in the tank. You also have a fuel pressure regulator before it gets to the injectors that keep the required pressure in the fuel system to make the fuel injectors work optimally. Best thing you can do is get a fuel pressure guage and see what the pressure is up near the motor where there is a fitting on the fuel rail that looks like an overgrown tire air fitting.

Good Luck

Dec 19, 2009 | 1998 Dodge Dakota

2 Answers

1996 LHS running gas out of exhaust.

Have you checked the spark plugs and wires? It could be you have one or more cylinders that are not firing and so the unburned fuel has to go somewhere (out the exhaust).

May 19, 2009 | 1996 Chrysler LHS

2 Answers

Cranks but no start

Sounds like the carb is dirty. I would check that before spending a lot of money of other things.

May 31, 2017 | 1990 Lincoln Town Car

1 Answer

Trouble starting

Do a bleed down test on the fuel pump pressure, hook up the test guage at the injector rail service schrader valve port and run engine for a moment , then turn it off and note the fuel pressure, wait a couple of hours, pressure should not drop more than 5 PSI, if it does replace pump and filter.

Aug 03, 2008 | 2006 Ford F-150

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts


Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides