Question about 1998 Chevrolet Blazer

1 Answer

I changed oil filler neck on a 1998 chevy blazer It will not lock in .How does it lock in?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 3,497 Answers

If I remember correctly, they are a light press fit with a "swedge" in the inside to secure it......you may have to epoxy it in place..
This is what I use... its comes in different "setting times" ....you should be able to purchase this at walmart, home depot, Lowes, hardware store...etc..it wil work..


DEVCON 2 TON EPOXY 84fl oz SYRINGE Walmart com

Posted on Aug 02, 2017

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 2920 Answers

SOURCE: Chevy Blazer 1992 Oil Pump Change

you have to drop the oil pan to get to it...once the oil pan is off there are 2 bolts that holdthe pump in place,,,you will also need a new screen for the new pump.

Posted on Jan 03, 2009

  • 132 Answers

SOURCE: 1998 chevy blazer oil leak

Yes you should be able to change it by yourself. It is pretty simple. It will save alot of money

Posted on Jan 30, 2009

davesmith_37
  • 94 Answers

SOURCE: cylinder 2 misfire on a 1998 chevy blazer

check your plug wires for tears and dont overlap them

Posted on Feb 27, 2009

  • 290 Answers

SOURCE: 1998 Chevy blazer radio wiring diagram

http://www.the12volt.com/installbay/stereodetail/435.html

Posted on Apr 03, 2009

jim9813
  • 124 Answers

SOURCE: Replacing fuel filler neck on 2000 Crown Vic

Good news, no the tank doesn't have to come down. However, there needs to be less than 3/4 tank. Jack it up and set on a jack stand, remove the wheel, four screws housing to pipe, filler pipe sensing hose from filler pipe, screw retaining the cap, four retaining screws from filler pipe, screw from filler pipe retainer, slide into the tank until it can be rotated and pulled out through the fender. lube the tank grommet with clean oil and reverse the removal for install.

Posted on Aug 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Must pump gas very slow to fill tank. 2001 chevy blazer s10


sounds like the ball check valve is stuck take a rubber hose stiff if you can find one and run it down filler neck with a little force to loosen the ball see if that helps

Aug 17, 2013 | 2001 Chevrolet Blazer

1 Answer

I have a 2002 Chevy blazer and it has a problem filling up the tank. It acts like it is full even when it is empty. What do i do to fix this


the vent tube in the filler neck is either plugged or disconnected, remove the filler neck to check it, lack of ventilation causes the gas to foam in the filler neck and triggers the filling nozzle

Nov 07, 2010 | 2002 Chevrolet Blazer

1 Answer

Instructions on how to remove fuel pump for 95 chevy blazer 4x4


Removal & Installation
To Remove:


  1. Properly relieve the fuel system pressure.
  2. Drain the fuel tank through the filler pipe.
  3. Support the fuel tank.
  4. Remove or disconnect the following:

    • Negative battery cable
    • Filler neck
    • Shield and tank straps
    • Fuel lines and vapor hose from pump and tank
    • Electrical connection from fuel pump
    • Fuel tank
    • Fuel pump/sending unit assembly by turning the locking ring (located on top
      of the fuel tank) counterclockwise using a spanner wrench
    • Fuel pump from the fuel lever sending device

To Install:


  1. Install or connect the following:

    • Fuel pump in tank with new seal around opening
    • Tank and connect fuel lines and vapor hose
    • Tank to the frame

      1. Torque to: 33 ft. lbs. (45 Nm)

    • Shield
    • Fuel filler neck and clamp
    • Negative battery cable

  2. Refill the tank.
  3. Run the engine and check for leaks.






View of the in-tank fuel pump assembly.
7924jg21.gif




prev.gif next.gif

Sep 23, 2010 | Chevrolet Blazer Cars & Trucks

3 Answers

Needs fuel pump


Removal & Installation To Remove:
  1. Properly relieve the fuel system pressure.
  2. Drain the fuel tank through the filler pipe.
  3. Support the fuel tank.
  4. Remove or disconnect the following:
    • Negative battery cable
    • Filler neck
    • Shield and tank straps
    • Fuel lines and vapor hose from pump and tank
    • Electrical connection from fuel pump
    • Fuel tank
    • Fuel pump/sending unit assembly by turning the locking ring (located on top of the fuel tank) counterclockwise using a spanner wrench
    • Fuel pump from the fuel lever sending device
To Install:
  1. Install or connect the following:
    • Fuel pump in tank with new seal around opening
    • Tank and connect fuel lines and vapor hose
    • Tank to the frame
      1. Torque to: 33 ft. lbs. (45 Nm)
    • Shield
    • Fuel filler neck and clamp
    • Negative battery cable
  2. Refill the tank.
  3. Run the engine and check for leaks.
View of the in-tank fuel pump assembly. 7924jg21.gif

prev.gif next.gif

Sep 18, 2010 | 1997 Chevrolet Blazer

2 Answers

I need to remove the fuel pump from my 99 chevy blazer , is there an access panel or does the fuel tank have to dropped?


  1. Properly relieve the fuel system pressure.
  2. Drain the fuel tank.
  3. Support the fuel tank.
    1. Remove or disconnect the following:
    2. Negative battery cable
    • Filler neck from the tank
    • Shield from tank and tank straps
    • Fuel lines and vapor hose from pump
    • Electrical connection from fuel pump
    • Fuel tank
    • Fuel pump/sending unit assembly by turning the locking ring (located on top of the fuel tank) counterclockwise using a spanner wrench
    • Fuel pump from the fuel lever sending device
  • To install:
    Install or connect the following:
    • Fuel pump in tank with new seal around opening

    NOTE The fuel pump strainer must be in a horizontal position when the fuel sender is installed in the tank. When installing the sender assembly, make sure that the fuel pump strainer does not block full travel of the float arm.


    • Tank and connect fuel lines and vapor hose
    • Tank to the frame. Torque the fasteners to 33 ft. lbs. (45 Nm).
    • Shield
    • Fuel filler neck and clamp
    • Negative battery cable
    1. Refill the tank.
    2. Run the engine and check for leaks.
    6207c87.gif
    View of the in-tank fuel pump assembly

    Oct 13, 2009 | 1999 Chevrolet Blazer

    1 Answer

    HOW DO I REPLACE THE FUEL PUMP ON 2003 CHEVY S10 PICK UP


    Removal & Installation To Remove:
    1. Properly relieve the fuel system pressure.
    2. Drain the fuel tank through the filler pipe.
    3. Support the fuel tank.
    4. Remove or disconnect the following:
      • Negative battery cable
      • Filler neck
      • Shield and tank straps
      • Fuel lines and vapor hose from pump and tank
      • Electrical connection from fuel pump
      • Fuel tank
      • Fuel pump/sending unit assembly by turning the locking ring (located on top of the fuel tank) counterclockwise using a spanner wrench
      • Fuel pump from the fuel lever sending device
    To Install:
    1. Install or connect the following:
      • Fuel pump in tank with new seal around opening
      • Tank and connect fuel lines and vapor hose
      • Tank to the frame
        1. Torque to: 33 ft. lbs. (45 Nm)
      • Shield
      • Fuel filler neck and clamp
      • Negative battery cable
    2. Refill the tank.
    3. Run the engine and check for leaks.
    1e2538e.gif

    Jun 26, 2009 | 1998 Chevrolet S-10 Pickup

    3 Answers

    How much will it cost for a mechanic to change oil pan gasket on my 1998 chevy blazer 4wd big v6 engine?


    Gasket = $35 (permatex rubber)
    Labor - my manual says 3 hours.
    You'll have to be responsible for figuring out the labor price per hour depending on where you are located.
    In MI, a garage is about $50/hr, and dealership = $85/hr
    CA might be $95/$150/hr.

    Parts are minimal on the job - its all labor.
    Figure in about $20 for shop supplies... gasket remover, sealant, rags, etc.

    Thanks for using FixYa - a FixYa rating is appreciated for answering your FREE question.

    Jun 02, 2009 | 1998 Chevrolet Blazer

    3 Answers

    Can't find the oil filter on 1998 chevy blazer


    there is a black cover right under the front of the blazer tha says oil filter acess

    Mar 21, 2009 | 1998 Chevrolet Blazer

    1 Answer

    1998 chevy blazer oil leak


    Yes you should be able to change it by yourself. It is pretty simple. It will save alot of money

    Jan 30, 2009 | 1998 Chevrolet Blazer

    2 Answers

    2004 and 2001, are parts interchangeable?


    Yes they are as long as the Motors are Similar.

    Jan 22, 2009 | 2004 Ford Crown Victoria

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    21 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts

    yadayada
    yadayada

    Level 3 Expert

    76846 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22246 Answers

    Ronny Bennett Sr.
    Ronny Bennett Sr.

    Level 3 Expert

    6918 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...