Question about Cars & Trucks

Open Question

4way flasher switch is not staying down - Cars & Trucks

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Signal light flasher 2001 2500hdsilverodo


turn on your 4way flashers ,and go under dash and feel fore the clicking next to the fuse box they are on a separate system but the flashers are all located in the same place also look in the owners manual

Jul 30, 2015 | Cars & Trucks

1 Answer

The indicator lights have come up on the dash,showing BOTH lights are ON. I cannot switch them off whilst driving or stationary. i have disconnected the battery and left ot overnight. i can lock the c


i would try changing the flasher relay as a starting point , just a thought i did have a 4way switch go bad once so before getting new relay disconnect the 4way switch and see if that cures the issue , keep me posted if you wish

Jan 31, 2015 | Cars & Trucks

1 Answer

Hazard Flashers


Replace the multi- functioning switch. it operates the turn signals,4way flashers,wipers and headlights.those are very common problem

Jan 03, 2014 | 2001 Jeep Grand Cherokee

1 Answer

Side lights,third brake light and dash lights come on when I press brake but no bottom brake lights. Then when I switch the lights on the side lights and third brake light stay on and when I press the...


sounds like a bulb is not seated properly in a socket in the back..check all the lights and groundwires too..starting with all the 4way flashers..then running lights.

Jan 25, 2013 | Cars & Trucks

1 Answer

2004 oldsmobile alero. How do you replace the blinker flasher


The signal light flasher is a big problem on most of these cars, the flasher is built inside of the 4way hazard light switch.
To replace the signal flasher you will need to replace the hazard light switch.

It sounds crazy but it is ture, replace the hazard switch and problem is solved, to replace the switch, you will need to pop off the ring that sits around 4way switch and then with small picks or screw driver gentle push tabs in and pry out, make sure to align switch so that the top is at the top when installing new one.

once switch is out of the dash you will then unplug the connector and its out, take new switch and plug in connector and make sure it goes in with the top at the top ( take note of the old switch before removal so that the new one goes in the same way)then slide new one into dash and it locks in, next is to install ring. most times this is the problem area, the ring, put a small mark on the top of ring so that you install it the same way otherwise it will not go in correctly. good day.

Jun 30, 2012 | Cars & Trucks

1 Answer

LEFT TURN &4WAYS WORK NO RIGHT TURN SI98 BUICK PARK AVE


The first thing is to replace the flasher, the 4ways and signals use diffrent flashers, after replacing the flasher or changing it with the 4way flasher and see what happens. if this doesnt help then you may have a bad signal switch, a good trick is to turn on the signal and watch it as you move the lever around, pull back a little or lift it more and pull down a little, sometimes the switch contact goes bad and by moving the lever without take signal off will make it flash and if that happens then the signal switch is bad even if the 4ways work this still means a bad switch, the 4ways are wired through diffrent contacts then each signal, good luck.

Mar 17, 2011 | 1998 Buick Park Avenue

1 Answer

Right forward and rear turn signals stay on solid even with key off and out


YOUR CAR USES A ELECTRONIC TURN SIGNAL FLASHER .IT CONTROLS THE 4WAY AND TURN SIGNALS SOUNDS LIKE THE FLASHER CONTACTS ARE BURNED FAST .REPLACE THE FLASHER UNIT.

Jan 09, 2011 | 1996 Ford Explorer

2 Answers

Brake lights and turn signals quit working


The first thing to do is check the fuses, the fuse may have blown, maybe to a short or bad bulb, start with the fuses and also make sure the 4way hazard lights switch is off.

Jun 26, 2010 | 1995 Mercury Grand Marquis

3 Answers

My blinkers will not blink they stay solid


THE INDICATOR RELAY NEEDS TO BE REPLACED

Jun 15, 2009 | 1993 Jeep Cherokee Country

2 Answers

2000 Pontiac Grand Am Flasher Relay


It's part of the hazard/4way flasher switch assy.

Nov 07, 2008 | 2000 Daewoo Leganza

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...