Question about Cars & Trucks

Open Question

I need reset program for printer pantum p1000

Printer pantum p1000

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 Ford Freester engine running but will not drive code P1000


P1000 fault code is a misnomer because it is not really a fault code. When this code is flashed in your dash panel, it just shows that the reset cycle of your engine computer is not completed yet. Normally, if you are resetting the code, you would disconnect the battery (-) terminal for 1 minute and reconnect. However, on some engines like Ford, the previous code is not totally erased yet so that this P1000 code will show up.

Nov 08, 2016 | Ford Cars & Trucks

1 Answer

What do codes P0411, P1000


P1000 code means the codes were cleared or the battery was disconnected
Powertrain Control Module (PCM) Reset Description All OBDII scan tools support the powertrain control module (PCM) reset.
The PCM Reset allows the scan tool to command the PCM to clear all emission-related diagnostic information. When resetting the PCM, a DTC P1000 will be stored in the PCM until all the OBD II system monitors or components have been tested to satisfy a drive cycle, without any other faults occurring. For more information about a drive cycle, refer to Drive Cycles .
The following events occur when a PCM reset is performed:
  • Clears the number of Diagnostic Trouble Codes (DTCs).
  • Clears the DTCs.
  • Clears the freeze frame data.
  • Clears diagnostic monitoring test results.
  • Resets status of the OBD II system monitors.
  • Sets DTC P1000.

P0411 Secondary Air Injection System Incorrect Flow Detected

neither of these could cause a no start or no crank problem . Is the battery good an do you have good connections on the battery ? Do the headlamps show bright when on ?

Oct 14, 2015 | 1997 Lincoln Continental

2 Answers

My car won't start and is showing a p1000 code . What does this mean?


P1000 is a manufacturer specific fault code:

Ford P1000: OBDII Monitor Testing Not Complete.
Jaguar P1000: Engine control module (ECM) - internal error.
Kia P1000: System diagnosis incomplete.
Land Rover P1000: Engine control module (ECM) memory erased - no codes stored.
Mazda P1000: OBDII Drive Cycle Malfunction.

So depending on the manufacturer of your car would depend on the meaning of a P1000 code!

Jan 21, 2015 | Cars & Trucks

2 Answers

P1000 code how do I remove this code


Hi, now it depends, I take you have a code reader? if so you should have a code reset? If the car is as you said, remove and clean injectors, I know its a pain, but as the car is not running this is the only way to clean them.
I hope this helps. What code reader are you using to know its code: P1000

Apr 06, 2014 | 1998 Jaguar XK8

1 Answer

I have a 2003 jaguar x-type awd but i been having the code p1000 i been driving my car for more than 200miles and i cant get any monitor to be reset as ready and im not able to pass my emission test c


code p1000 refers to system readiness test not complete. There are no causes for this listed so the problem will be in the CPU program that is not progressing through the tests that it does after starting the car. Possible way to overcome this is to use a scanner to reset the program as it is obviously corrupted compare this problem to a PC that turns on and before starting the task bar stops in a loop that says installing settings.

Mar 21, 2014 | Jaguar X-Type Cars & Trucks

1 Answer

P1000


This code, really isnt a fault code, P1000 refer at readiness monitors not set since last reset. needs more drive cycles to finish emission self tests.

Hope helps.

May 07, 2013 | Ford Cars & Trucks

1 Answer

P1000 code


P1000 is a default, it show that the PCM has been reset and the PCM has not had time to verify all the reading need.
It also a good way for those that have an intermittent Code light not to pass their inspections if they think just by resetting the PCM will get them by, As P1000 although is not a fault, you still can not pass (in states with inspections)

Hope this helps; also keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using Fixya, and have a nice weekend.

Nov 19, 2011 | 1998 Ford Explorer

2 Answers

P1000 problem loss of power after 10 minutes


P1000 is not really a fault code, if there are no there are no other codes stored then perform the following:

Disconnect the positive terminal on the battery, hold the terminal to the chassis for 2 - 3 seconds, this defuses the ecu and drains stored data thus clearing P1000.

Now wait 10 minutes.

Then reconnect battery.

Start car *without touching gas pedal*

Leave car idling for a good 5 - 10 minutes then jump in and go on a minimum 12 mile drive, you will need to perform a few normal driving conditions, fast, slow, stop, pull away etc so just a normal day to day trip to the town would suffice.

Hopefully this will sort it, if not report back

Regards

Lloyd


Aug 20, 2010 | 2002 Jaguar X-Type

2 Answers

I used an SCT livewire tuner and it came up with a trouble code of P1000. What does this code mean?


P1000 code means "testing incomplete". You can not reset this code, drive the vehicle and code should clear when the system recovers all testing data.
This can occur when the battery is disconnected for an extended period of time.

Nov 08, 2009 | 2006 Ford Mustang

3 Answers

What dose the code p1000 mean and p1645


P1645 EVAP Solenoid Output Circuit
P1000 Scan not complete. meaning it didnt finish scanning

Sep 14, 2009 | 2002 Jaguar X-Type

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

37 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...