Question about Cars & Trucks

Open Question

The lock stays in the unlock position until I pull out the batteries

Posted by on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 21 Answers

SOURCE: 2008 Tarus X headlights flash till battery runs

sounds like a door sensor and or alarm issue. Your car should still be under waranty.

Posted on Aug 11, 2010

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Resetting convenience features after battery replacement


put key in drivers door lock, rotate and hold in unlock position until all windows open. then rotate and hold in lock position until all windows close.

Dec 15, 2013 | 2009 Volkswagen Tiguan

1 Answer

Camry rear seat won't unlock


The plastic pull on the top of the seat may have been screwed down too much. If that happens, it will not allowing the lock mechanism to fully unlock. Unscrew the top plastic pull a little at a time and at the same time reach around and pull the lock leaver up until it is in the full unlock position. You should then be able to pull the plastic lever up normally and fold down the seat.

Nov 06, 2013 | 2001 Toyota Camry

1 Answer

1988 CADI Eldorado Barrites, 4.5 liter v8: locked keys in car, call locksmith, put air bags in door for space in order to slide his metal stick in to unlock, pull the handle, push the electric door lock...


You most likely have a central locking system that will stay locked until you can unhook the battery. This is sounds like a similar problem I had with my 95 BMW.

Mar 15, 2011 | 1988 Cadillac Brougham

1 Answer

94 VW Golf horn stays on with fuse pulled, I just got this car and tried to install a new battery when I connect it the horn sounds.I checked the fuse panel and pulled # 13 that was for the horn and it...


What your hearing is the factory alarm not the horn. Connect the battery when the alarm sounds go to the drivers door lock with the key and lock and unlock the door until the alarm goes off . Then reinstall the fuse for the horn.,

Feb 15, 2011 | Volkswagen Golf Cars & Trucks

1 Answer

My keyless entrey will not work has new battery?


Hi, please try reprogramming the fob using these procedures, and thankd for using FixYa:
Close all doors
2. Insert key into ignition
3. Hold down the power UNLOCK button on the driver's door panel, continue to hold down
until instructed to release in step 9.

4. Perform steps 5 through 8 in a fairly rapid succession.
5. Turn the ignition to the ON position (as far as you can go without starting the engine.)
6. Turn the ignition to the OFF position.
7. Turn the ignition to the ON position (as far as you can go without starting the engine.)
8. Turn the ignition to the OFF position.
9. Release the power UNLOCK button on the door panel. The vehicle should respond by
door locks locking and unlocking automatically. (If locks do not cycle after you let go,
not before you let go of the unlock button, then the vehicle has not entered programming
mode and you must start procedure over. Remove key from ignition, open drivers door
and return to step 1 ). If the locks do cycle automatically then proceed to step 10.

10. Hold down the LOCK and UNLOCK buttons on the remote until the doors lock and
unlock. This may take up to 30 seconds.

11. Repeat step 10 NOW for each additional remote. (Including any existing remotes).
12. Turn the ignition to the ON position to exit the programming mode.
13. Test remote(s).

Jan 14, 2011 | 2003 GMC Sierra 1500

1 Answer

I changed batteries in my 2003 GMC Sierra key fob


1. Close all doors
2. Insert key into ignition
3. Hold down the power UNLOCK button on the driver's door panel, continue to hold down
until instructed to release in step 9.

4. Perform steps 5 through 8 in a fairly rapid succession.
5. Turn the ignition to the ON position (as far as you can go without starting the engine.)
6. Turn the ignition to the OFF position.
7. Turn the ignition to the ON position (as far as you can go without starting the engine.)
8. Turn the ignition to the OFF position.
9. Release the power UNLOCK button on the door panel. The vehicle should respond by
door locks locking and unlocking automatically. (If locks do not cycle after you let go,
not before you let go of the unlock button, then the vehicle has not entered programming
mode and you must start procedure over. Remove key from ignition, open drivers door
and return to step 1 ). If the locks do cycle automatically then proceed to step 10.

10. Hold down the LOCK and UNLOCK buttons on the remote until the doors lock and
unlock. This may take up to 30 seconds.

11. Repeat step 10 NOW for each additional remote. (Including any existing remotes).
12. Turn the ignition to the ON position to exit the programming mode.
13. Test remote(s).

Mar 06, 2010 | 2003 GMC Sierra 1500

1 Answer

Battery went dead in 2007 Chevy Silverado truck. Now, remote does not work. Replaced battery in remote and it still does not work.


Make sure you have one working ignition key and all remotes for the vehicle.

1) Close all vehicle doors.
2) Insert the key into the ignition.
3) Hold down the power UNLOCK button on the driver’s door panel-continue to hold down until instructed to release in step 9.
4) Perform steps 5 through 8 in fairly rapid succession.
5) Turn the ignition switch to the ON position (as far as you can go without starting the engine).
6) Turn the ignition switch to the OFF position.
7) Turn the ignition switch to the ON position.
8) Turn the ignition switch to the OFF position.
9) Release the power unlock button on the door panel. The vehicle will lock and unlock the doors automatically.
10) Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until the door locks and unlocks. This step may take up to 30 seconds.
11) Repeat step 10 NOW for each additional transmitter (including any existing transmitters).
12) Turn the ignition switch OFF then to the ON position in order to exit the transmitter programming mode.

Feb 28, 2010 | 2007 Chevrolet Silverado 1500 2WD

1 Answer

Short..think its in door locks Kills battery in day and half when put pos cable on...doors unlock


PUT A AMP METER IN LINE WITH TE POSITIVE BATTERY CABLE. AND SEE HOW MUCH IT IS DRAWING THEN START PULLING FUSES UNTIL YOU FIND THE CIRCUIT THAT IT IS IN THEN REPAIR IT...

Nov 07, 2009 | 1993 Chrysler Lebaron

1 Answer

Cant get back door to stay closed . The lock is stuck in locked position I think and the door is open. When I go to close it, it is'nt staying closed. Had to duck tape it to stay closed. LOL! I keep...


It sounds to me ( correct me if I'm wrong ) like the door latch on the side vertical edge of the door is in the LOCKED POSITION. In order to unlock it perform the following. First electrically with the LOCK button UNLOCK the locks. Now with one hand hold the OUTSIDE DOOR HANDLE IN THE OPEN POSITION, while at the same time FLIPPING OPEN THE LATCH. All Done . Now you can close the door. Hope this helps

Jun 27, 2009 | 1997 Chevrolet Lumina

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

11 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...