Question about Cars & Trucks

Open Question

I can't pull out the pressure balancing unit from the brace fitting in the wall

Posted by on

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 193 Answers

SOURCE: removing of power steering pressure hose

The brace is there to stabilize and hold the power steering hose. When the pump is in operation, if the hoses weren't locked down they would jump all over the place and do damage to themselves.

If you need to remove the bracket, go ahead. Just be sure you put it back on.



Hope this helps.


If you would like to correspond further with me on this or any other issue, please feel free to do so.
Bill
ASE Master Technician

Posted on Nov 26, 2008

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I get the old harmonic balancer off.


A puller is often required. Parts stores sell balancer removal pullers for not very much. Usually there is just enough room to fit the puller onto the balancer and pull it off. Sometimes the inner fender wheel liner must be pulled off and set aside.

May 10, 2015 | Cars & Trucks

1 Answer

How do you replace the crankshaft front dampener


Remove all belts/serpentine belt. Remove crank bnolt if it has one. Use 1/2 impact wrench for this operation. Fit harmonic balancer puller and pull off. If no bolt ,fit puller and pull off. It will be keyed so installing new unit will be reverse to removal

Feb 03, 2013 | 2001 Chevrolet Malibu

2 Answers

It is hard to turn on both sides how do i change my steering pump


Have you checked the fluid level and belt tightness?
It is easy to change the pump.
There is the small high pressure hose and the larger return hose, a pivot bolt, and the adjustable hold down bolt.

Aug 13, 2010 | 1998 GMC Sierra

1 Answer

Looking for low pressure ac connection


The low pressure side of the ac unit is the big aluminum pipe coming from the compressor, it usually goes back along the fire wall to the passenger side of the car, it has a small cap with an "L" on it, It is the only place that the filler will fit. Check it out , Hope this helps.

Aug 01, 2010 | 2002 Lincoln LS

1 Answer

1996 Honda Odyssey. Loud vibration from heater fan behind dash. What is the best way to get to the fan / shroud ?


just above passengers feet area, pull the blower out, 3 or 4 bolts,most likely it has debris and leaves, making it out of balance. its also a good time to replace the cabin air filter. the cabin filter, you will need to remove the glove box, brace and cut a plastic brace out, the plastic brace was there for support when the dash was made, but now, it is no longer is needed

Oct 22, 2009 | Honda Odyssey Cars & Trucks

1 Answer

I need to replace my timing belt on my hyundia elantra 2003 with 1997 cc engine


Dear Friend
Removal: Support engine: remove -engine mounting, auxiliary drive belt, water pump pulley, crankshaft pully bots & crankshaft pully, timing belt covers....turn crankshaft to TDC on No 1 cylinder, ensure crankshaft sprocket, camshaft sprocket, oil pump sprocket & balancer shaft sprocket timing marks lighned. Pls note: Timing marks on camshaft sprockets should align with cylinder head uppter face, dowl pins on camshaft sprockets should face downwards....Slacken tensioner botl. Move tensioner away from belt & tighten bolt.
Remove: automatic tensioner unit bolts, automatic tensioner unit, timing belt, crankshaft bolt, crankshaft sprocket, crankshaft sprocket guide washer...slacken balancer shaft belt rensioner bolt, move tensioner away from belt & lightly tighten bolt...Remove balancer shaft belt.

Installation:
ensure timeing marks aligned.Note: Timing marks on camshaft sprockets ahould align with cylinder head upper face, exhaust sprocket mark is on recess but inlet sprocket mark is on tooth. To check oil pump sprocket positionded sorrectly: remove blanking plug from cylinder block, insert 8mm diameter Phillips screwdriver in hole. ensure screwdriver is inserded 60mm from face of cylinder block. If screwdriveer can only be inserted 20mm-turn oil pump sprocket 360". Inset screwdiver again.
Fit balancer shaft delt in anti-clockwise direction starting at crandkshaft sprocket....Slacken balancer shaft belt tensioner notl, turn tensioner clockwise to tension belt. Tighten bolt to 15-22 Nm... Applu thump pressure to belt at tentioner, belt should deflect 5-7mm. If not: Repeat tensioning procedure.... Install - chankshaft sprocket guide washer & crankshaft sprocket.
Thighten crankshaft centre bolt, tightening torque:110-130Nm. Please note, ensure crankshaft sprocket guide washer is fittet correctly. oil threads & contact face crankshaft botl before fitting.

Sep 21, 2009 | Hyundai Elantra Cars & Trucks

3 Answers

Oil pressure light came on engine is knocking like no oil is


hi what what engine?
if it's knocking then most likely damage has been done to the bearings

May 27, 2009 | 1999 Oldsmobile Alero

1 Answer

Removing of power steering pressure hose


The brace is there to stabilize and hold the power steering hose. When the pump is in operation, if the hoses weren't locked down they would jump all over the place and do damage to themselves.

If you need to remove the bracket, go ahead. Just be sure you put it back on.



Hope this helps.


If you would like to correspond further with me on this or any other issue, please feel free to do so.
Bill
ASE Master Technician

Nov 23, 2008 | 1999 Chevrolet Malibu

1 Answer

Low oil pressure


I believe your sending unit is located on the top of the block, towards the fire wall. You can get an inexpensive pressure test gauge and put in place of your sending unit. It should be a 1/4" NPT fitting. Does the pressure gauge fluctuate between low and high RPM? If so, chances are that your oil pump may need to be replaced.

Jun 29, 2008 | 1984 Chevrolet Camaro

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

13 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...