Question about Cars & Trucks

Open Question

I did my metric in 2010 i want to rewrite where can apply ?

I am located in honeydew,Randburg . thank you

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Cylinder head bolt tension for 2010 Mitsubishi FN64F 6M60-3AT2


The term you mean is actually torque. Cylinder head torque is usually specified in foot pounds, or in the metric world, newton meters. It describes how much twisting force should be applied to tighten the head bolts.


www.engineaustrailia.com.au/products/diesel-engine-parts/mitsubishi

Apr 20, 2017 | Mitsubishi Cars & Trucks

1 Answer

2010 impala high beams do not come on, light on dash comes on, replaced bulbs still don't work, checked all fuses, look good


High Beam Headlamp Operation
Battery voltage is applied at all times to the coil and switch sides of the HIGH BEAM PCB Relay located in the underhood fuse block. When the headlamp dimmer switch is placed in the high beam position, the headlamp dimmer switch signal circuit to the BCM is pulled low signaling the headlamp high beam request. In response to this signal, the BCM applies ground through the high beam relay control circuit energizing the high beam relay. With the high beam relay energized, battery voltage is applied through the switch side of the relay, the left and right high beam fuses, and the high beam supply voltage circuits illuminating the high beam headlamps. At the same time the BCM sends a GMLAN serial data message to the instrument panel cluster (IPC) requesting the IPC to illuminate the high beam indicator. Ground for the left headlamp is provided at G101 and the right headlamp at G100.

Nov 23, 2016 | 2010 Chevrolet Impala

1 Answer

Hub nut size on 2010 equinox...1 5/16????


metric size usually 32MM, but could vary between 30-35MM if it was replaced with an aftermarket one.

Apr 07, 2016 | Cars & Trucks

1 Answer

How replace sensor1 bank1 Honda odyssey 2010


disconnect the plug then use a 7/8" or equivalent metric wrench to un-screw the sensor from the exhaust. sometimes you have to heat the exhaust around the sensor to get it un-seized.

Apr 21, 2015 | 2010 Honda Odyssey

1 Answer

How to locate 2010 dodge journey evap. system to fix po441 code


Code P0441 is for evaporative purge performance and may be a false code which can be corrected by a newer computer flash update. This would be a free service at the dealer due to a -Rapid Response Transmittal- so call a dealer and have them run your VIN number to see if may apply due to build date of vehicle.

Apr 21, 2014 | 2010 Dodge Journey

1 Answer

Rear hub assembly 2010 hub assembly


cheaper to let shop fix. because you need tools like jack stands torque wrench,arbor press need basic mechanic tool set like all metric and standard type wrenches and socket sets.you need almost $1000.00 tools to do your own work.

Nov 08, 2012 | 2010 Dodge Avenger RT

3 Answers

Where is the evap vent valve soleniod located on Chevy impala 2010


The evap vent valve is locate behind the left rear tire,You will need to remove the tire and the plastic covers, the vent valve is located on the top of the filler pipe, filler pipe is the pipe in which you fill your gas tank.

the valve sits atop the pipe near the top, i will enclose a diagram picture to help you locate it. you can also test valve with a battery when you remove it. the valve should allow you to blow air through it and then when power is applied to valve it should close and no air should flow through it.hope this is helpful. good day.
4_12_2012_11_00_04_pm.gif

Apr 12, 2012 | 2010 Chevrolet Impala

1 Answer

Peugeot 207 spark plug size


8 mm according to my Pugeot and Mercedes reference.

I would have a complete set of 3/8" Metrics 12 pt sockets on hand to be sure at the time of doing the job as sometimes our manuals are not exact due to the many variables.

It shows a thin walled 12 point metric. I know my BMW uses a 10MM thin walled for the irridium plugs.

You can find the tool mentioned on eBay, it has a special clip to retain the plug as you extract & insert it.
Mercedes M156 engine, Peugeot 207 and 307, Renault 1.2 16v SPARK PLUG SOCKET 8MM Item #120884075060.

Good luck!

Mar 27, 2012 | Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...