Question about Nissan Cars & Trucks

Open Question

NISSAN 1400 TORQUES IN NEWTON METRES MAIN BEARING , CONORODE BEARING AND CYLINDER HEAD.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
NismoMaster
  • 146 Answers

SOURCE: torque settings for cylinder head nissan sentra

Tighten in sequence to 29ft.lbs then tighten in sequence to 58ft lbs. then loosen all bolts. Then tighten in sequence to 33ft lbs. then tighten each bolt in sequence 90 degrees then tighten each bolt again 90 degrees

Posted on Jul 26, 2009

Ad
  • 115 Answers

SOURCE: cylinder head torque settings for a toyota 1493cc

If you have a vehicle application for the motor you can get a Haynes or Chilton manual from your local auto parts store. They usual run around $30.

Posted on Sep 04, 2009

drsinister69
  • 2317 Answers

SOURCE: What is the right Torque Specification of the

Cylinder heat bolt torque:
Torque sequence --------- front | 7 3 1 5 | | 8 4 2 6 | --------- Step 1: Torque all bolts in sequence to 14 Ft/Lbs Step 2: Torque all bolts in sequence to 29 Ft/Lbs Step 3: Torque all bolts in sequence to 36 Ft/Lbs Step 4: in the sequence, loosen the cylinder head bolts three turns. Step 5: Tighten short bolt to 15 - 32 Ft/Lbs Step 6: Tighten long bolt to 30 - 36 Ft/Lbs Step 7: Tighten all bolt to 175- 185 degree note: Do not loosen all of the cylinder head bolts at one time. Each cylinder head bolt must be loosened and the final tightening prior on the next bolt in the sequence.
Main bearing torque:
Torque sequence: Step 1: torque bolts to 91 Ft/Lbs with the exception of the rear main bearing cap Step 2: torque rear main bearing cap bolts to 88 Ft/Lbs Step 3: torque brace bolts to 40 Ft/Lbs
Connecting rod torque:
Torque sequence Step 1: Torque to 29 Ft/Lbs Step 2: Turn an additional 90 degrees

Posted on May 18, 2010

  • 9 Answers

SOURCE: main bearings and big end bearings tension specs

This site has all the torque specs you should need make sure this is the correct engine.

http://www.davidfarmerstuff.com/C6Z06-Torque.pdf

Posted on Dec 27, 2010

  • 1 Answer

SOURCE: I am busy with an

timing marks

Posted on May 19, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

FORD torque


the info that i have are for engine codes wl and wl2 (turbo) are
stage 1 27to 32 newton metres
stage 2 plus 90 degrees

Feb 16, 2018 | Ford Cars & Trucks

1 Answer

Main bearing cap bolt torque specs for a 1999 2.0 Ford engine


See #1; Main bearing diagram
See #2; NM conversion chart

  1. NOTE: The crankshaft must rotate freely; if necessary check and adjust the bearing clearances.Tighten the main bearings and connecting rod bearings.
    1. Tighten the main bearing bolts in two stages.
    • Stage 1: 25 Nm.
    • Stage 2: 60 degrees.
    1. Tighten the connecting rod bearing bolts in two stages.
    • Stage 1: 25 Nm.
    • Stage 2: 90 degrees.






# 2) Newton Meters conversion chart:
http://extraconversion.com/energy/newton-meters/newton-meters-to-foot-pounds.html

#1)
25730427-ddvrxh52bv4dwu240r4mw22m-2-0.gif saailer

Jun 05, 2015 | Ford Cars & Trucks

1 Answer

Model 1400. What are bolt torque settings?


get to auto zone and buy the book for that vehicle . you'll find all of them there . thanks.

Dec 05, 2011 | 1997 Nissan Pickup

1 Answer

How much n- m must i torque my nissan sentra 1400 gxi cylinder head


1.8L 4 cylinder

cylinder head bolt torque

bolts 1-10 ( large bolts )

step 1 21 ft lbs.
step 2 44 ft lbs.
step 3 loosen all bolts
step 4 21 ft lbs.
step 5 additional 50-55 degrees

bolts 11-15 small bolts

56-74 in. lbs

2.0L 4 cylinder

step 1 29 ft lbs.
step 2 58 ft lbs.
step 3 loosen all bolts
step 4 23-25 ft lbs.
step 5 additional 90-95 degrees
step 6 additional 90-95 degrees

Apr 30, 2011 | 2000 Nissan Sentra

1 Answer

What is the right Torque Specification of the cylinder head bolt,main bearing and connecting rod bearing for a 1997 Ford F 150 4.2 liter? Thank you...


Cylinder heat bolt torque:
Torque sequence --------- front | 7 3 1 5 | | 8 4 2 6 | --------- Step 1: Torque all bolts in sequence to 14 Ft/Lbs Step 2: Torque all bolts in sequence to 29 Ft/Lbs Step 3: Torque all bolts in sequence to 36 Ft/Lbs Step 4: in the sequence, loosen the cylinder head bolts three turns. Step 5: Tighten short bolt to 15 - 32 Ft/Lbs Step 6: Tighten long bolt to 30 - 36 Ft/Lbs Step 7: Tighten all bolt to 175- 185 degree note: Do not loosen all of the cylinder head bolts at one time. Each cylinder head bolt must be loosened and the final tightening prior on the next bolt in the sequence.
Main bearing torque:
Torque sequence: Step 1: torque bolts to 91 Ft/Lbs with the exception of the rear main bearing cap Step 2: torque rear main bearing cap bolts to 88 Ft/Lbs Step 3: torque brace bolts to 40 Ft/Lbs
Connecting rod torque:
Torque sequence Step 1: Torque to 29 Ft/Lbs Step 2: Turn an additional 90 degrees

May 17, 2010 | 1997 Ford F150 Regular Cab

1 Answer

2003 mazda 6 3.0 need the main bearing torque specs


I'm sending you the torque specifications for your main bearings and also your head bolts. I also sent you main bearing and cylinder head tightening sequence. I hope this will be useful2c713bf.giffce6623.gif
Main Bearings Torque specs. 40-43 Ft. Lbs.
Cylinder Head Torque specs. 56-60 Ft. Lbs.

Oct 05, 2009 | 2003 Mazda Mazda6

1 Answer

Differential Torque settings for 2003 Town Car


New cylinder head bolts are required and an angle guage,or you can make one up with card and a set square. Head bolt torque is 25Nm(newton metres)+60degrees + 60deg + 60 deg so it's a four step process.Con.rod bolts(big-end)28Nm,Inlet manifold 28Nm,Exhaust manifold 25Nm, Crank pulley 40Nm,Sump 5Nm and use locking compound (loctite)Timing cover 6Nm. Valve clearance,set inlets to .006" and ehausts to .010"(set approx.when cold then re-adjust while warmed engine is idling.

Feb 20, 2009 | 2003 Lincoln Town Car

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

77544 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...