Question about Cars & Trucks

Open Question

Torque setting for h100 main bearing ,big end bearing and cly. Head torque

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
joecoolvette
  • 5660 Answers

SOURCE: cly head torque settings

There are four bolts on top, and four bolts on bottom.
At the Top, starting from the Left side, the bolts are numbered ->
6, 2, 3, and 7.
At the Bottom, starting from the Left side, the bolts are numbered ->
5, 1, 4, and 8.

Sequence for tightening, of course, is to go from 1 through 8.
The best way to torque engine head bolts, is to tighten in a three stage tightening sequence. The bolts are finally tightened to 33 Foot Pounds,
and an additional turn of 90 degrees. Not trying to insult your
intelligence in any way, but I would like the additional 90 degree turn,
to be clear.
There are 360 degrees in a circle. If you go halfway, you have gone 180
degrees. If you go one-fourth the way, you have gone 90 degrees.
When you are getting ready to torque this final 90 degree turn, look to
make sure the end of your torque wrench has a clear path, so that you
will not be stopped somewhere along the way.

I advise torquing the head bolts to 15 lbs first. Then 25, then 33. Then go back one more time, for the additional 90 degree turn. Seems like a lot of hassle, but it's easy to warp this head. Remember, if you are not using some type of permatorque head gasket that has teflon, Like a Felpro Blue for example), after the engine has reached operating temperature Once, you have to go back, and retorque the head.

Posted on May 17, 2009

Ad
michael_grey
  • 365 Answers

SOURCE: engine bearing torque settings big end and main bearing

4 cylinder correct?
1bac25a.jpg

Posted on Jun 20, 2009

  • 167 Answers

SOURCE: WOULD YOU KNOW THE TORQUE SETTINGS FOR MAIN

Mains Stage 1 83nm
Mains Stage 2 167nm

Big ends Stage 1 29nm
Big ends Stage 2 45 - 60 degrees

Hope this helps

Posted on Jul 10, 2009

  • 115 Answers

SOURCE: cylinder head torque settings for a toyota 1493cc

If you have a vehicle application for the motor you can get a Haynes or Chilton manual from your local auto parts store. They usual run around $30.

Posted on Sep 04, 2009

  • 1 Answer

SOURCE: i need to know the torque settings for 850cc reliant robin

go to
http://mankymonkeymotors.co.uk/Trikespageimages/relianttorquesettings.html

a target="_new" href="http://www.leafletflyers.co.uk/">Leaflet Distribution in Croydon</a>, Leaflet Distribution in Balham, <a target="_new" href="http://leafletflyers.co.uk/Leaflet-Distribution-Streatham.htm">Leaflet Distribution Streatham</a>.

Posted on Aug 08, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I need the big end torque on the Rocam engine please


A cheap shop manual will have this and much more. If you are in this deep you probably need one.

Sep 05, 2016 | 2000 Ford Ka

1 Answer

Torque settings on a yaris 1.3 16v big ends,mains,flywheel,cylinderhead


Toyota Yaris Main and Big end Torque settings:
Tighten the main and big end bolts in sequential order and in two steps.
Main bearings. Stage 1.
22 ft lbs.
Stage 2.
44 ft lbs

Big end bearings.
Stage 1.
11 ft lbs.
Then Rotate bolt head a further by 90 degrees

Head bolt torque must be done in 3 steps:
1st 22 ft lbs
2nd 43 ft lbs
final 47 ft lbs
use this sequence of tightening:
9 - 3 -1 -6 -8
7 - 5 - 2 -4 - 10

Flywheel spec:
65 ft lbs

Jul 15, 2016 | 2007 Toyota Yaris

1 Answer

Hi i have daewoo matiz 800cc can you help me by giving me the torque settings for the big end bearing caps please


You are looking for the torque settings for big end bearings and main bearings on a daewoo matiz?
Main bearings torques on a Daewoo Matiz 800cc (1999)
Stage 1: 25-30 Nm
Stage 2: 55-60 Nm
Big End Bearings…

Mar 09, 2016 | Daewoo Cars & Trucks

1 Answer

Torque settings on Hyundai h100 big end bearings


It is a great website.. If you are games lover and love to play games word cookies game download is the most easiest way to get latest games hill climb racing 2 anytime you need to follow just few simple steps five nights at freddy’s 4 | hotmail login

Jun 08, 2015 | 2008 Hyundai H100 2.6iD

1 Answer

Torque settings for chevy spark 800cc


Write your answer...hi I need torque settings for 800cc Chevy spark 2005model Big end and mains barring 3cylimder

Jul 11, 2012 | Cars & Trucks

1 Answer

Hyundai h100 2008 2.5d crankshaft and big end torque settings


which torque of crank bearing rod for Hondai H100

May 26, 2012 | Hyundai Cars & Trucks

2 Answers

WOULD YOU KNOW THE TORQUE SETTINGS FOR MAIN BEARING AND BIG END BEARING CAPS FOR ISUZU 4JG2 ENGINE


Mains Stage 1 83nm
Mains Stage 2 167nm

Big ends Stage 1 29nm
Big ends Stage 2 45 - 60 degrees

Hope this helps

Jul 10, 2009 | 1994 Isuzu Trooper

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...