Question about Cars & Trucks

1 Answer

Just had my 95 jimmy smogged, passed was running great. While driving it it stalled at an intersection. It started up and ran a mile or to and stalled again.Did this 4 tmes now it wont start

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 5,617 Answers

Any codes?

Posted on May 19, 2017

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 Rav 4 periodically stalls at low idle, intersections


Start with the throttle body. I use brake clean and a toothbrush. Clean the plate and were it sits. Wouldn't hurt to spray down the MAF sensor, if it has one. Once you do it, it will take a few seconds to start. Once started, rev it up and spray inside the throttle. Keep it running. Most times this is a $4 fix.

Aug 20, 2016 | Cars & Trucks

1 Answer

Where is OBD 1 connector location for 1993 Nissan SE-V6 4x4 pick up?


Try disconnecting your battery for 2 minuets then reconnecting the battery . This probably will turn the light off.. then see how long it takes to come back on.. I had Mitsubishi that we never could find out what turned the light on.. The dealer even checked it and could not find the problem (did not even charge us) .. When we would turn off it would stay off for a couple of days.. so to smog it we would turn it off, smog it and worry about it in 2 years..Car ran great, always passed smog eaisly and got over 30mpg and went 200,000 miles..

Aug 20, 2014 | Cars & Trucks

1 Answer

Won't pass smog when it should...


Just because the car seems to run well, does not mean the emissions are within spec. For example, you could be running a little rich and the car will start and run great, but the exhaust is not within code.
What you can do is take it to a "smog shop", that is a repair shop with the proper equipment to diagnose the problem. If the testing is simply the reading of the on board computer codes, then most any place can read those, but you need an experinced mech to know what to do about it. May need an exhaust gas analyzer to physically sample and analyse the gasses. For the actual test, as long as the computer says all is fine, usually, you're good to go.
If the computer looses power any saved run data will be lost and must be re-accumulated to pass the smog test. A few hours to a day is usually enough run time to accumulate enough data.

Dec 04, 2013 | 1999 Saturn SL

1 Answer

2004 PT Cruiser Turbo won't pass smog test because computer monitors haven't completely reset after battery failure. It's been driven 235 miles and only 2 monitors remain unset (oxygen and


The system has to see a wide range of conditions before a smog test can be done. On most brands you have to drive at least 50 miles, at various speeds including stop and go, let it idle for 5 - 10 minutes, and run at freeway speed for at least 25 miles. It also has to reach normal operating temp of 195 degrees.

Apr 22, 2013 | 2004 Chrysler PT Cruiser

1 Answer

My 1999 jeep grand cherokee stalls when i am coming to a stop. it starts right back up and runs normal.


change your crankshaft position sensor if it still does it then change your camshaft postion sensor

Mar 02, 2013 | 1995 Jeep Grand Cherokee

1 Answer

My 95 626 with a 2.0 4 spd won t pass smog. i changed plugs, wires, distributor,cap and rotor. when cold it will idle,but as soon as it s warm it starts idling rough and sometimes will die.it won t pass...


you may be having trouble with the catalytic converter its not very hard to change
but before you do any thing take your car to auto zone or advanced auto hook it
up to the portable computer and see what the computer wants you to do its easy
to use and its free to use

hope this helps you
good luck
bob

May 10, 2011 | Mazda 626 Cars & Trucks

1 Answer

What is the drive cycle for a 1998 Aurora, Battery was disconnected and need to reset sensors. Will not pass or fail smog test. Was told that i needed to do a Drive Cycle to reset the sensors?


This means you must drive the car long enough for all of the self-tests to run. Depending on the test it could be a single start and run to many cycles and many miles. Usually after about 50 miles of driving you have completed most tests.
I'm not sure where you are located, but in Ohio you can ask and have the car run on the dynamometer and compete your smog test this way.

Oct 11, 2010 | 1998 Oldsmobile Aurora

1 Answer

Ticking noise coming from engine, loss of power, runs very rough!


check inj thay do click but not very load but becuase it might be it damaged it is doing this

Aug 10, 2009 | 1996 GMC Jimmy

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...