Question about Dodge Ram 1500

Open Question

Torque setting and pattern for tighting on a 3.7l Dodge Ram 1500

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 840 Answers

SOURCE: passanger side mirror replacement on 04 dodge ram 1500?

very easy take the mirror inside cap off if you can not get to the 3 bolts then you will have to take trim panel off to take trim panel off look for plastic caps take them out and unscrew them then pop out the bottom of the door and pop the sides out then lift up and out should be loose enough for the bolts now/ 10mm bolts 3 Please rate my response thank you very much

Posted on Feb 02, 2009

Ad
  • 1 Answer

SOURCE: 1998 dodge ram 1500 v85.2 towing capacity?

according to the owners amnual the max towing weight for a 1999 ram 1500 quad cab wit automatic transmission is 7600 lb.
with either 5.2 or 5.9 v8. for a reg cab it is 8000 lb.

Posted on Jul 23, 2009

outdoorsman5
  • 631 Answers

SOURCE: 1999 Dodge Ram 1500 Pickup error code p0171

This code means that system to lean, bank 1.
some of the possible causes to make this code set are
1. intake or exhaust leak,
2. problem with the air system.
3. MAF (Mass Air Flow sensor)VAF sensor (Volume air flow sensor)
4. fuel pressure/pump
5. injector(s)
6. HO2S (Oxygen sensor)

Posted on Sep 16, 2009

wilsodfarm
  • 986 Answers

SOURCE: torque specs. for outer tie rod ends for 2006

Tie rod end is 35 ft. lbs. Pinch bolt for the lower ball joint - 105 .I hope this helps you

Posted on Oct 06, 2009

Testimonial: "thanks for the help"

  • 15 Answers

SOURCE: what are the front axle nut torque specs for a

185 ft.lbs

Posted on Oct 10, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I need to know the torque specs for these wheels


Are you talking about lug nuts? Your owners manual says 130 ft lbs.
Use criss/cross pattern and tighten in increments, like 45 ft lbs first for all, then 90 ft lbs and finally 130 ft lbs. You get the picture.

Jan 10, 2016 | Dodge Cars & Trucks

1 Answer

How much torque for each head bolt in a 2004 Dodge ram 1500 3.7 liter


Install the cylinder heads. Use new gaskets and tighten the bolts, in sequence, as follows:
  1. Step 1: Bolts 1-8 to 20 ft. lbs. (27 Nm)
  2. Step 2: Bolts 1-10 verify torque without loosening
  3. Step 3: Bolts 9-12 to 10 ft. lbs. (14 Nm)
  4. Step 4: Bolts 1-8 plus 1 / 4 (90 degree) turn
  5. Step 5: Bolts 9-12 to 19 ft. lbs. (26 Nm)


26002143-2qxw3km0vcnqu3setvnduoab-2-1.gif

Dec 10, 2015 | Dodge Cars & Trucks

1 Answer

Torque specs for upper and lower ball joints and inner and outter tierods 2001dodge ram 2WD


Just get them tight? I have never nor have I seen anyone torque a front end part in the last 15 - 20 years.

Sep 08, 2013 | 2001 Dodge Ram 1500 Truck 2WD

1 Answer

What are the Tourque settings for a 2000 dodge ram 1500 with a 5.9L motor?


The torque specs for what nut or bolt? Each has it's own rating. Some may be as low as 5 ft lbs, some may be as high or higher than 100 ft lbs

Mar 14, 2011 | 2000 Dodge Ram 1500 Truck

1 Answer

Torque procedure on american axle 11.5


Tight tight rtight tight and so on alternating criscross pattern

Sep 29, 2009 | 2007 Dodge Ram 3500 Quad Cab Laramie

1 Answer

2005 dodge ram need to find out drive pattern to


http://www.discountedwheelwarehouse.com/Vehicle_Bolt_Pattern_Reference.cfm i think this ste link will do the needful for u

Jun 15, 2009 | 2005 Dodge Ram 1500

1 Answer

Need to the torque specs for a 1999 Dodge Durango


Head Torque sequence Step 1: torque to 50 Ft/Lbs Step 2: torque to 105 Ft/Lbs recheck final torque in sequence.

Torque intake manifold: Step 1: 12 inch/Lbs, (hand tight) Step 2: 72 inch/Lbs, (6) Ft/Lbs Step 3: 12 Ft/Lbs
torque intake plenum: Step 1: 24 inch/lb (hand tight) Step 2: 48 inch/lb (4) Ft/Lbs Step 3: 84 inch/lb (7) Ft/Lbs (To torque bolts, start in center using crisscross pattern)

Apr 07, 2009 | 1999 Dodge Durango

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...