Question about Chrysler Cars & Trucks

Open Question

I need help troubleshooting a a/c that won't cool properly in a 2006 Chrysler minivan. I did the key trick and got the following code.. sof 8.2 e . I checked clutch fuse, and freon bottle flagged red

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 1 Answer

SOURCE: fuse for stereo/cd in chrysler town and country minivan

Its in the box next to the battery and i had the same problem.The fuse is on the first line top.

Thanks

Posted on Mar 08, 2009

Ad
bunnydawg
  • 5158 Answers

SOURCE: power sliding doors

you need to locate the relay for the sliding door in the fuse panel and replace it

Posted on Mar 09, 2009

chrisK1997
  • 103 Answers

SOURCE: A/C compressor won't turn on

yes it could....could also be a bad low pressure switch or you may have a freon leak and lost all of the refrigerant

Posted on Apr 19, 2009

  • 543 Answers

SOURCE: how to replace rear brakes on a 2006 chrysler

take the wheels off the front,,remove the 2 bolts holding the brakes caliper to the caliper mount and pull off the caliper,then remove the old pads by popping them out, and the remove the 2 bolts holding the caliper mounting bracket to the hub and then remove the rotor,,,to either resurface it,,or replace it with a new one,,,the put the rotor back on(new one) install the mounting bracket and pads and press the caliper piston in with a pliers and then put it back onto the mounting bracket and then tighten all bolts,and do the other side,,pump up brakes and youre good to go

Posted on Oct 08, 2009

cool78259
  • 228 Answers

SOURCE: ac was working fine the

Check the low switch by the dryer or accumulator, its a long narrow cannister,

it will have a pressure switch attached to it or near it. put your, ac on high,

pull the molex off the switch and jump the molex with a wire or paperclip,

if the compressor comes on and the ac starts to cool, you will just need

to replace the low pressure switch, if the clutch does not come on,

check the low switch molex to see if there is 12vlts there. good luck!

Posted on Jun 28, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2006 town and country minivan running hot after replacing thermostat


Well Michele, you have several problems. First the cooling system, you have at least two problems, even if you replace the antifreeze the system can hold the correct pressure because of the leak; on top of that you have or a broken cable or a stucked valve on the heating system that means there is fluid trapped inside the system that should be flowing to the engine with the rest of cooling liquid. With the car off rey to move the temperature selector from cool to hot and try to hear if there is any sound of parts moving... Of you can here it, the cable/link is working but you have problem with the valve that's not openning, you need to replace it.

About the steering try to see if the leak is in a hose or in the pump(is attached to the engine, where you refill the steering fluid) in any case you need to take it to the shop to be replace/fix.

Feb 10, 2014 | 2006 Chrysler Town & Country

1 Answer

Chrysler town and country 2006, gave these codes P0700, P048.0 and P063.3. What do they mean?


code po700 refers to transmission control system/ MIL --malfunction====causes---wiring---TCM
As to the other codes they are specific to the manufacturer and will require determination from a service centre

Feb 09, 2014 | Chrysler Cars & Trucks

1 Answer

Car wont start..after i stuck wet keys in ignition


Give the key-hole a few days to dry out. There are electronics inside the key-hole that sense the key's position and the immobilizer chip within the key. If these short out, or any other circuits with them, the car won't start/run properly.

Jun 19, 2012 | 2006 Chrysler 300

1 Answer

How do I properly replace my 2006 Chrysler Sebring ac condenser? Can I use a condenser from a 2004 Chrysler Sebring?


You can replace the condenser easy enough

You won't be able to recover the refrigerant when
you start,so right there your breaking EPA Laws

Then you won't have gauges or a vacuum pump,
so you can not even work on the A/C System
to test or charge it !!

Jul 18, 2011 | 2006 Chrysler Sebring

1 Answer

How to get the ingnition tumbler out of a 2001 chrysler t&c minivan i have everything torn down but cant figure how to get it out


most igntion switches are removed by tuning the key to the on position and inserting a pin punch or similar tool 1/8" in diameter into the hole on the underside of the housing, pushing the locking pin in while pulling the switch out.

Apr 10, 2010 | Chrysler Town & Country Cars & Trucks

1 Answer

Minivan has no interior power or lights without key on


There are three possible situations I can think of. 1, there are usually switches on the main interior light that can be turned off to stop the lights from coming on when the door is opened unless the ignition is on. 2. There is a problem with the ECM or Alarm that was installed. 3. There is a fuse out. Check your fuses on the interior and under the hood of the vehicle.

Nov 20, 2009 | 1999 Chrysler Town & Country

1 Answer

2003 chrysler town & country speedometer stuck


sit in the drivers seat close the door. with the key off hold the trip odometer button in then while holding the button in turn the key on. if done correctly this will put the MIC (mechanical instrument cluster) into a self test. if the speedometer does not move like the rest of the gauges during this test the MIC must be replaced. if the speedometer does move it is likely your problem will be fixed, however, if the speedometer does move but it does not start working properly then further diagnostic will be needed.

Mar 19, 2009 | 2003 Chrysler Town & Country

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8575 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...