Question about Cars & Trucks

Open Question

Function knob not working model TSSTTVDG01 - Cars & Trucks

Posted by on

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why wont my 2001 ford windstar blow out of vents ? only on defrost?


Air Flow Control
Air flow control is accomplished in the following manner:
  • Primary control is through the function selector knob , mounted on the heater function selector switch, which is part of the heater control .
  • The function selector knob has the following positions: OFF, PANEL, PANEL/FLOOR, FLOOR, FLOOR/DEFROST and DEFROST.
  • The heater function selector switch combines a vacuum selector valve with an internal electrical switch.
  • The vacuum selector valve directs source vacuum to various vacuum control motors (18A318) . Refer to the System Airflow Schematic and Vacuum Control Charts.
  • An internal single-pole electrical switch is also controlled by the selector. The switch controls the electrical supply to the heater blower motor switch (18578) .
  • The position of the function selector knob determines the manner in which the system will operate.
  • Each position of the function selector knob is detented for positive engagement.
  • You probably have a vacuum leak , Pull heater control panel an check for vacuum . A broke vacuum hose or The vacuum selector valve is bad ! Or check for a vacuum hose in the engine compartment being off somewhere !

Mar 08, 2015 | 2001 Ford Windstar

1 Answer

Change gear knob


This is an "it depends" answer. It depends on the type of gearshift knob and its installation. If your vehicle is equipped with a manual shift and the shift lever is little more than a steel rod sticking up from the console, then it is easy to replace.

To replace it, simply do this:

1. Set the parking brake
2. Take the car out of gear
3. Center the gearshift
4. Place a piece of cloth around the gearshift knob to prevent damage
5. Place a ViceGrip (R) or pair of pliers around the cloth on the gearshift knob and gently begin turning the knob to the left
6. Spin the knob off the shaft

Remember, though, this works only if the gearshift knob does not have another function combined. For example, you might find a reverse gear actuator on the top of the gearshift knob or you might find a reverse actuator button on the front face of the gearshift knob. This type of combined function gearshift knob is usually found on automatic transmissions.

If you want to remove the gearshift knob from this type of shift, see the service manual and obtain the tools you will need as this type of gearshift knob is much more complex to remove and involves many different systems that have to be addressed before the knob will come off.

It is better to leave this type of fix to trained technicians.

If you need further information or if you would like to see information on automotive safety please visit this site: Safecar infoCar safety Insurance Magazine

Nov 12, 2014 | Cars & Trucks

1 Answer

1997 Ford Taurus front defrost not working


. Air won't blow out of the floor or center vents just defrost ? Do you have manual or automatic climate control ?
Air Flow Control
Air flow control is accomplished in the following manner:
  • Primary control is through the function selector knob mounted on the A/C-heater function selector switch, which is part of the integrated control panel.
  • The function selector knob has the following positions: OFF, MAX A/C, A/C, PANEL, PANEL/FLOOR, FLOOR, FLOOR/DEFROST and DEFROST. The A/C-heater function selector switch combines a vacuum selector valve with an internal electrical switch.
  • The vacuum selector valve directs source vacuum to various vacuum control motors (18A318). Refer to the Vacuum Control Diagram , System Airflow Schematics and Vacuum Control Chart .
  • Two internal, single-pole electrical switches are also controlled by the A/C-heater function selector switch. The combination of these electrical switches controls the electrical supply to the A/C clutch and heater blower motor switch (18578).
  • The position of the function selector knob determines the manner in which the system will operate.
  • Each position of the function selector knob is detented for positive engagement.
  • Vacuum Control Motors The vacuum control motors (18A318):
    • are located on the A/C evaporator housing, A/C recirculation air duct and heater air plenum chamber (18471).
    • direct system airflow to the vehicle interior as determined by the remote climate control module or manual override.
    • The five-passenger seating configuration has an additional vacuum control motor mounted on the heater air plenum chamber to control airflow to the rear seat A/C register (19893).


vacuum control motor-i4bq0ig33y1522pr2d2rrkk3-2-0.gif

Jul 09, 2017 | Ford Cars & Trucks

1 Answer

The lights inside dashboard knobs & multi-function display went out


I'm not sure what model Toyota you have, but in a Camry, the cause is most likely a blown fuse. This is a 10A fuse labelled "Gauges" located behind a cover in the dash panel

Dec 13, 2011 | Toyota 4Runner Cars & Trucks

1 Answer

Why wont my turn signals and wipers work?


The turn signals, wipers, and head lamps are controlled by multi function knobs on the steering column. Due to constant use their internal metal contacts can wear and corrode, preventing proper operation. You may be able to open the knobs and clean the contacts, if this doesn't work the unit must be replaced. Removal of the unit, which consists of the knobs on both sides of the column, requires removal of the steering wheel and should only be done by a trained professional.

Feb 28, 2011 | 2005 Kia Sorento

2 Answers

My 2006 C280 was due for service B , and I just did the oil change only. How can I reset service B message on the car computer ?


Reset process should be listed in the owners manual.

Should be something like turn car to on(not running) press trip button twice, turn to off and hold trip button till it resets.

Apr 19, 2010 | 2007 Mercedes-Benz ML320 CDI

1 Answer

1984 ford mustang - windshield wipers only work when pushing on the knob, but not when turning the knob. help???


the electrcial contacts in the mulit function switch are probably coated or oxidized. try to take switch apart and clean it thoroughly

Dec 16, 2009 | 1984 Ford Mustang

2 Answers

No heat


THE AIRDUCT EXCHANGE FUNCTION IS NOT WORKING , IT MAYBE THE CONTROL SWITCH ITSELF .WHAT TYPE OF VEHICLE IS IT

Aug 12, 2008 | 2005 Chevrolet Malibu

1 Answer

The ac won't work right


The first knob controls the temperature. Turning it counterclockwise will lower the temperature, clockwise will raise it. Pressing the button will turn on the circulate function (recirculates the air from the cabin).
The second knob controls the fan speed. Counterclockwise will reduce the fan speed, clockwise will increase it. Pressing the button activates the A/C compressor (allows colder temperatures).
The third knob controls the flow direction. Each picture indicates where the flow will go. Pressing the button activates the rear defoggers (in some models, it will also activate the heated side mirrors).

Jul 06, 2008 | 2008 Mitsubishi Lancer GTS CVT Sedan

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...