Question about Cars & Trucks

1 Answer

2006 E450 disconnected and reconnected battery and now wrench and engine light come on and no acceleration,,,,what to do?

Posted by on

  • Bill George
    Bill George May 17, 2017

    Put key in ignition Push gas pedal to floor......let off Turn key on as if you were gonna start it up don't...push gas to floor.....let off Turn key off Turn key on and start

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 2,372 Answers

I found a couple things for you to try.
1. after a new battery is installed you need to keep the car running until it reaches operating temp. Once it gets there for a few minutes turn the AC on full blast to teach the idle pattern.
2.

Posted on May 17, 2017

  • Bill George
    Bill George May 17, 2017

    Put key in ignition Push gas pedal to floor......let off Turn key on as if you were gonna start it up don't...push gas to floor.....let off Turn key off Turn key on and start

  • Joanne Barrette
    Joanne Barrette May 18, 2017

    Thank you Bill...we have tried both solutions to no avail...we are baffled...we tried the instructions in the manual of what to do after reconnecting the battery and nothing...I guess we will have to get the codes off it but we can't drive it to a service garage(no acceleration)...at a loss...thanks again

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

When I tried to change battery alarm and all lights went on. How to install new battery in Nissan xtera 2006?


Disconnect the negative cable first and then the positive cable and remove the battery. The lights/alarm will go out when battery is disconnected and may come back on when reconnected. Use door lock key fob to shut alarm/lights off if they come back on when battery is reconnected

Jul 09, 2015 | 2006 Nissan Xterra

1 Answer

How do I change the starter for my 2006 Chrysler Sebring touring


You'll need a set of metric sockets and end wrenches. Then disconnect the positive battery cable. Wrap the terminal you removed from the battery in a rag and secure it away from the battery. Follow the positive battery cable down to the engine block. It will most certainly be connected to the starter. Remove the cable and any other small wires. Make a diagram showing where to reconnect them. Remove 2 14 mm bolts from the starter to bell housing. Remove starter. Reverse the procedure to install new one.

Jan 26, 2015 | 2006 Chrysler Sebring

1 Answer

Why is the wrench light on the dash, no DTCs, and runs fine?


try disconect baterry for % mins while battery disconnected ,switch headlights on to discharge computer box capacitors .......so it loses fault memory........reconnect switch ignition on and wait 30 sec before starting .........see if light re appears afterwards .good luck

Aug 19, 2014 | 2006 Ford Mustang V6

1 Answer

Removed battery cables on my 2006 Freestyle. After cleaning I replaced the cables and when I started the car it now has check engine code and wrench light on gauges on as well and the car will not...


Tom, you will have to get the code read to see what the problem is. The one other thing to try is disconnect the + cable on the battery and let it sit for 10 minutes before hooking it up again to reset the computer.

Oct 24, 2013 | 2005 Ford Freestyle

1 Answer

How do i reset computer ? Tail light was stuck on killing battery and i removed fuses now engine light in dash is on and does't start


Hello simply disconnect the battery terminals wait a minute or two then reconnect this is the way the computer is reset be sure to use proper size wrench for battery terminals.

Feb 16, 2011 | 2005 Chevrolet Uplander

1 Answer

How do i reset change oil light after oil change


This is n easy fix.
Just take and disconnect your positive battery cable for a moment, and then reconnect it.
This should remedy your lite problem. If it does not that you have something else amiss.

Happy Motoring.

The Wrench

Oct 10, 2010 | 2006 Hummer H3

2 Answers

2006 Saturn Vue Check Engine Light


Disconnect the battery wait 10 minutes, then reconnect it.

Jul 12, 2009 | 2006 Saturn Vue

2 Answers

Check Engine Light


I had the problem with the engine light and the ESC light on. At the same time the car would not accelerate. I disconnected and reconnected the battery and works fine now.

Aug 13, 2008 | 2006 Hyundai Sonata

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

35 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...