Question about Pontiac Cars & Trucks

Open Question

How to repair glove door on pontiac g8 - Pontiac Cars & Trucks

Posted by on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 12449 Answers

SOURCE: Fuel door won't open on a 2008 g8 pontiac

Fuel Fill Door Description and Operation
The fuel door latch actuator shares the circuit with the driver door latch assembly. The body control module (BCM), upon receipt of a lock switch lock or unlock signal, will switch the appropriate door lock actuator, as well as a fuel filler door release actuator control circuits to battery positive voltage. The opposing side of the door lock and fuel filler door release actuators is connected to ground by the I/P fuse block through the other door lock actuator control circuit and the doors, along with the fuel filler door release, will lock or unlock as commanded.
Circuit/System Testing

  1. Ignition OFF, disconnect the harness connector at the fuel door release actuator.
  2. Test for less than 1 ohm between the control circuit terminal 1 and ground.
  3. ?‡'
    If greater than the specified range, test the control circuit for a short to voltage or an open/high resistance.

  4. Test for less than 1 ohm between the control circuit terminal 2 and ground.
  5. ?‡'
    If greater than the specified range, test the control circuit for a short to voltage or an open/high resistance.

  6. Connect a test lamp between the control circuit terminal 1 and control circuit terminal 2.
  7. Ignition ON, command the doors to LOCK and UNLOCK by using the door lock switch. The test lamp should illuminate while commanding the LOCK and UNLOCK states.
  8. ?‡'
    If the test lamp remains OFF during either command, test either control circuit for a short to ground.

  9. If all circuits test normal, test or replace the fuel door release actuator.
Component Testing
  1. Ignition OFF, disconnect the harness connector at the fuel door release actuator
  2. Install a 15A fused jumper wire between the control terminal 1 and 12V. Momentarily install a jumper wire between the control terminal 2 and ground. The fuel door release actuator should perform the LOCK/UNLOCK function.
  3. ?‡'
    If the function does not perform as specified, replace the fuel door release actuator.

  4. Reverse the jumper wires. The fuel door release actuator should perform the UNLOCK/LOCK function.
?‡'
If the function does not perform as specified, replace the fuel door release actuator.


Remove the rear compartment side trim (right) panel. Refer to
Rear Compartment Side Trim Panel Replacement .

Posted on Apr 06, 2016

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the map sensor location on a 2008 pontiac g8 3.6L LY7


Should be on the left side of engine, center, top

Nov 10, 2016 | 2008 Pontiac G8

1 Answer

I'm trying to turn on my fog light for Pontiac g8 2009


Pull the switch that turns your light on to your driver seat. I got a g8 to and it took me a while to figure it out.

Feb 21, 2016 | Pontiac Cars & Trucks

3 Answers

Driver window does not work ,i bought a new switch its not that , i checked window moter not that checked fuses not sure about that but the one listed yes i checked


If the switch, the motor, and the fuse are ok I would look for faulty or broken wiring. As far as I know there are no extra inline fuses in the window circuits.

Feb 04, 2016 | 2009 Pontiac G8

2 Answers

Where is the fuel vapor canister located on a 2008 pontiac g8


i beleive its under the hood or under the vehicle

Feb 24, 2015 | 2008 Pontiac G8

1 Answer

Locations of fuse box and relay switches for a 2009 pontiac g8


On this website (link below) you find fuse box diagram, description and location for Pontiac G8 (2009)

Pontiac G8 2009 fuse box diagram Auto Genius

May 04, 2014 | 2000 Pontiac Grand Prix

1 Answer

Cigarette lighter not working on my pontiac g8


Don't change fuses unless blown. Usually, in the G8, the aux power F14 20 amp fuse blows before either the F22 or the F13. I bet that's what is blown in yours--it's usually what blows in mine.

Apr 05, 2013 | 2009 Pontiac G8

1 Answer

Pontiac G8 makes a rumbling noise during acceleration


MOST GM PRODUCTS HAVE A 5 YEAR 60,000 MILE WARRANTY. IF YOU FALL IN THAT AREA MAKE THEM FIX IT FOR FREE. IF YOU DONT THIS CAR HAD EXHAUST ISSUES CHECK FOR LOOSE HEAT SHIELDS.

Feb 22, 2013 | 2009 Pontiac G8

2 Answers

How do you remove the factory floor mats from a 2009 Pontiac G8?


Usually, you have to pull the seats and console, and trim panels for total release.

Sep 02, 2010 | 2009 Pontiac G8

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

42 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8557 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...