Question about Cars & Trucks

Open Question

Need turn signal assembly 86 g2 - Cars & Trucks

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No power to coil with ignition on. Power at pin 30 all the time and pin 86 with ign on. negative at pin 87. 12v at pin 85.turn key on power at coil for 2 sec. Power at cavity 3 at comp. Fuel pump ok. Code...


Mike, I don't know what you are working on, Chrysler? Chevy? Chrysler and Jeep have an Automatic Shutdown Relay for power to the coil. But the only thing I know that gets a 2 second signal with key in on, is the fuel pump relay. The pcm sends a 2 second signal to pin 85 or 86 of the FP relay with key on to prime the fuel system. Do you need a wiring diagram?

Mar 16, 2015 | Cars & Trucks

1 Answer

1991 Honda Accord Front turn signal assembly


You will need to remove the plastic steering column cover to access the turn signal assembly. Once in there, the signal assembly is held on by a few screws with one electrical plug attached.

Sep 15, 2011 | 1991 Honda Accord

1 Answer

Where is the turn signal flasher located on a 86 Camaro ?


Hello Tom.

The turn signal flasher is mounted to the right of the steering column, under the dash.
Here is a diagram to help you.
This view is from the back side of the instrument panel looking downward.
kiltylake_220.gif

If you need further assistance in locating this, please ask me in a comment.
Thank you for using FixYa.
KL

Mar 10, 2011 | Chevrolet Camaro Cars & Trucks

2 Answers

How do you replace the front turn signal on a 2005 Buick Terraza?


Changing front, right turn signal on 2005 Buick Terraza: Open hood; when facing the front of vehicle, the right turn signal is on the passenger side (left). The headlight assembly needs to be removed to easily reach the turn signal. On my vehicle, there is a 10 mm screw on the left side. Remove it. There is L-shaped pin on the right side of the headlight assembly. Swing the pin counter-clockwise (to the left). Pull the pin straight up to remove. The headlight assembly is now loose, but there is a pin snapped in a socket on the back of the assembly that still holds the assembly. Pull the headlight assembly hard and straight to the front of the vehicle. When it snaps loose, the assembly is now held just by the rubber gasket surrounding the assembly. You need to gently work the right side of the gasket out of the grill cowling. The assembly should pull straight out. The wires are long enough to lay the headlight assembly in the engine compartment. Finally, the turn signal is now accessible. Twist the light holder counter-clockwise and pull out the light holder. Change the bulb. Do not punch your man-card for credit until you have successfully reinstalled the headlight assembly. It goes back in a little easier the second time. Once you have put the L-pin in place, the screw back, and successfully tested the lights, you can now punch your man-card.

I give the mechanical engineers and designers a D-minus instead of an F only because I was successful on the first try. No light bulb on anything commonly used by people should be this hard to figure out.

Sep 07, 2010 | 2005 Buick Terraza

2 Answers

I need to replace the front turn signal light socket on a 2000 Chevy Venture, but i don't know how to get it out and i can't find a replacement. How do i get it out?


There are detailed instructions in the the manual. If you do not have a manual, here is how to do it (directions assume removing drivers-side headlight assembly and viewing the area from the front of the van): Remove the thumb screw on the left side of the headlight assembly as well as the thumb screw on the top of the head light assembly. The third thumb screw simply anchors the turn-signal assembly to the head light assembly. Initially, just loosen that screw. The whole assembly is now loose but still held in by two plastic posts on the bottom of the headlight assembly and two plastic posts on the end of the turn-signal assembly closest to the fender/wheel area. Pull the whole assembly kind of up, out, and down. It takes a bit of juggling but it will come out. Once the whole assembly is out you can separate the turn-signal assembly from the head light assembly and put the headlight assembly back in place. To separate the assemblies remove the third thumb screw (if its too tight to remove by hand you will need a Torx screw driver of size T-30; if you don't have a Torx a small flathead screw can work); also, you will notice the hidden clip that is the final anchor holding the turn-signal assembly to the head light assembly. Use a flat-head screw driver to release it. Now the units should be separated. To remove the turn signal bulb socket from the turn-signal assembly, simply turn it counter-clockwise while pressing down on the safety clip and pull it out of the back of the turn-signal assembly. The owners manual lists the type of bulb. It should be an amber 3157. The bulb pulls straight out of the socket.

Replace the bulb. Place the socket back into the turn-signal assembly (turn it clockwise until the safety clip snaps). Replace the Headlight assembly (two thumb screws and the two plastic alignment posts anchor it), but do not tighten the screws until the turn-signal assembly is in place. Replace the turn-signal assembly by first aligning the plastic posts and then anchoring it to the head light assembly with the third thumb screw. Make sure everything is aligned properly and tight all the thumb screws. An experienced person can probably make this change, start to finish, in 15 minutes. First timers will probably take 30 minutes as it takes some time to understand how the designers anchored everything.

Good luck and thank you for using Fixya

Mar 07, 2010 | 2000 Chevrolet Venture

1 Answer

How to change 4 runner front blinker light. there's a phillips screw under the hood I have removed but there is another fastener in the lower portion of the blinker housing I cannot locate.


Remove or disconnect the following:
  • Connector
  • Screw
  • Claw fitting
  • Front turn signal lamp assembly
  • Front turn signal lamp plug assembly
  • Front turn signal lamp bulb as shown
6191f4c.gif
c741133.gif
To Install:
  1. Install or connect the following:
    • Front turn signal lamp bulb
    • Front turn signal lamp plug assembly
    • Front turn signal lamp assembly with screw
    • Connector

Oct 01, 2009 | 2004 Toyota 4Runner

1 Answer

How do i install a new front turn signal bulb on my 2000 pontiac montana


You have to remove the headlight assembly to remove the turn light assemble. There are two mounting bolts that hold the headlight assembly to the frame that needs to be removed and one mounting bolt that holds the turn signal light assembly on the headlight assembly that needs to be removed. Once all three bolts (black plastic in colour with a wing nut) have been removed the headlight and turn signal assembly can just be removed. Take note that the assembly has a guild slot to be guild in place back when re installing the head light and turn signal assembly. Good luck and hope this helps. Keep me posted and I'll try to explain in a different way if i was un clear, Harder to explain then doing the job it self. 

Jul 20, 2009 | 2000 Pontiac Montana

1 Answer

Need to take out


Disconnect the battery. Remove the steering wheel. Remove turn signal switch,Remove the buzzer switch with needle nose pliers. Then insert the key(make sure it is not in place beforehand) and place in lock position. remove lock cylinder retaining torx screw. Then with key in place, pull out the assembly straight out.Disconnect the electrical connector from the bulkhead connectorand remove retaining clip. attach some wire to the connector to help with installation and pull harness through column. Installation is reverse.

Jul 06, 2009 | 1984 Chevrolet Camaro

3 Answers

86 toyota pickup fuse box diagram


When I use my turn signal in my 1986 toyota pickup every 5-6 uses it blows the fuse and my blinkers, backup lights, gas gauge and temp gauge stop working. What is going on

Jan 07, 2009 | 1986 Toyota Pickup 4WD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

27 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...