Question about Cars & Trucks

Open Question

My 2010 1600 Rocam Bantam battles to start when cold, as if the choke is not on. When warm, it starts first time.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: I have ford bantam 1.6i rocam 2006 model. It Doesn't start, It doesn't pump the petrol, the is no power to fuel pump

Refer to your manual there is a switch that deactivated the fuel pump in case of accident, there is a switch by the pasangers feet that if in the up position is activated to stop the fuel...

Posted on Aug 30, 2012

emissionwiz
  • 75108 Answers

SOURCE: diagram how to replace fan belt on ford bantam rocam engine 1.6

Here is the diagram I show.
9_28_2012_8_40_43_pm.jpg

Posted on Sep 28, 2012

  • 3 Answers

SOURCE: ford bantam rocam 1.6i speedo,temperature gauge and rev counter not working

Sometimes when the batery of vehicle goes flat or when u fit a new car batery to the bantams they love to give that problems like gauges not working rpm not working speedo not working and cluster display is dead, u disconect the batery termanils and for example fit positive termanil and arc. Or short til that blue spark occur then u swop around negative on and arc positive,leave the ignition switched on arc til gauges move!! Don't ask me why but that happend to me! A autoelek friend of mine showed me this! NB don't tri this with vehicles with a lot of elektric featers it can cause demage to ecu (engine control unit)

Posted on Oct 16, 2012

  • 98 Answers

SOURCE: hard starting, rough idle when cold, then smooth running when warm

Need year/make/model/mileage of vehicle to provide a more specific set of troubleshooting steps.

When was the last tune up? Hard starts when cold are usually caused by fouled spark plugs, worn plug wires, or weak ignition coils. Fuel systems are not as effected by temperature changes as the ignition components.

Posted on Nov 28, 2012

SOURCE: Hi i have 2004 1.6 ford bantam rocam that wont start, all the dashboard light come on but thats it! Checked all the normal suspects, new starter, battery all fuses check and replaced the crank angle s

firstly,check that the car has spark and petrol,from there you can be assured that it is a electrical problem

Posted on Jul 13, 2013

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where are the speed sensor situated on a Ford Bantam 1.6 rocam


It is plugged into the transmission where the speedo cable would go in older cars.

Jun 22, 2016 | 2008 Ford Bantam 1.6i

2 Answers

How do I fix a Bantam that wont start?


no idea but change the mass air flow sensor on or in the inlet manifold

Jan 03, 2016 | 2005 Ford Bantam 1.3i

1 Answer

Why is my ford bantam 1.3 cranking but not starting?


probably the immobilizer has been activated
check fob key battery
reset the immobilizer using a scan tool on the ECM

Oct 09, 2015 | Ford Cars & Trucks

1 Answer

Will a 1.6 Ford Bantam Rocam motor fit onto a 1.3 Ford Bantam Rocam gearbox, and is the engine mounting brackets the same


same engine, same year only difference is bore size so there is every chance that it will fit.

Jan 25, 2015 | Ford Cars & Trucks

1 Answer

My ford bantam 2008 model rocam 1.6i xl does not start after accident when I bridge fuel pump it does start. please help


check for the reset button not sure where its located at on your vehicle if you have the owners manual it should show location most the time the button will trip after a accident or even a hard bump

Sep 26, 2014 | 2008 Ford Bantam 1.3i

1 Answer

Ford 1 3 rocam engine


bantam?
most cars, MPI injection the injector form a sandwich.
between the fuel rail, and the intake front tunnel tubes.
so remove the rail,
step s
remove battery neg lug, so some, odd person dont try to start car.
depressurize the fuel system per FSM.
then remove injector conn plugs.
the unbolt rail. bingo.

the FSM covers this, ask ford parts counter for this book.

The Ford Bantam is a coupe utility vehicle ("bakkie", "pickup", or "ute") produced by the Ford Motor Company in South Africa. It spanned into three different models and was produced in South Africa for the local market.

be safe.

Jul 09, 2014 | 2005 Ford Bantam 1.6i

1 Answer

Ford bantam does not start


Check the reset switch near yo icu. reset it if off

Mar 16, 2013 | 2005 Ford Bantam 1.3i

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...