Question about Hyundai Cars & Trucks

Open Question

1-3 Hyundai Getz 2005. Do hydraulic lash adjusters need to be installed in certain position

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 53 Answers

SOURCE: hyundai getz

if the speedo still works then it will need a spedo unit if the speedo doesn't work it is either the cable or the gear in the trans to check the cable unthread from trans and attach a drill to the cable innereds spin the drill if the speedo does not move replace the speedo cable

Posted on Oct 18, 2008

ghost4548
  • 776 Answers

SOURCE: hyundai getz radio

Here's a pic

5781d0b.jpg
Pops out, then remove 4 screws which mount the audio & instrument panel.7be2186.jpg

Posted on Jun 05, 2009

  • 1757 Answers

SOURCE: timing belt diagram for 2005 1300 hyundai getz

My sincere apologies for the delayed response.
I am personally going back to answer your unanswered questions.
I have only been a free contributor to this site for the past 4-months.

I do not know if you still need this information, but I am going ahead and answering it anyway. You may want to Print the Diagrams for future use.

CLICK
on the following LINK. It has the 2005 Hyundai Accent Timing which have Timing Belt Diagrams very similiar to what you will need.

If you would: Before Clicking: Let me know if this helped you, or if you have any additional information or questions. Feel Free to contact me at FixYa.com!

Again my apologies...
http://www.2carpros.com/car_repair_information/year/2005/make/hyundai/model/accent/2005_hyundai_accent_timing_belt_diagram_marks.htm

Posted on Mar 08, 2010

  • 4793 Answers

SOURCE: Hyundai 2004 Getz. Is there an adjustment within

pop the bonnet,kneel down in front of the headlight and you will see an adjusting screw,on top and to one side of the headlight(sometimes has a spring behind it)one does up/down the other does left/right.remember if the oncomming driver is effected by too high a beam you can be fined(lots)

Posted on Jun 17, 2010

alicantecoli
  • 22156 Answers

SOURCE: I have a 2005 Hyundai

dont think this vehicle has a fuel filter ,only a gauze inside the fuel tank on teh bottom of the sender/pump unit ,best advice i can give is that if it runs ok leave well alone you should never need to clean it out as modern petrol pumps in garages have micronic filters inside the delivery pumps .

Posted on Jan 23, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Adjust rocker arms on 1990 2.9 ford


this is from the AutoZone web site.

2.9L Engine
No periodic valve lash adjustments are necessary on this engine. The engine utilizes a hydraulic valvetrain to automatically maintain proper valve lash. However, some earlier models have an adjusting screw on the rocker arm, which is used when assembling the engine to properly preload the lifter. If the engine has been disassembled, and the valve train parts were not kept in order, or there is an audible sound from the rocker arms while the engine is running, perform the adjusment procedure below.
The following procedure should be performed on a cold engine.
  1. On the cylinder to be adjusted, position the cams so that the tappets are in the base circle area.
  2. Loosen the adjusting screws until a distinct lash between the roller arm pad and the valve tip can be noticed.

The plunger of the hydraulic tappet should now be fully extended under the load of the internal spring.
  1. Carefully screw in the adjustment screws until the roller arms slightly touch the valves.
  2. To achieve the normal working position of the plunger, screw in the adjusting screw 1 1 / 2 turns, equivalent to 2mm.


  3. here is the site address. scroll down the page & you will see your engine size - 2.9
SAVE 20 GET BONUS 10 GIFT CARD ON ONLINE SHIP TO HOME ORDERS OF 100 OR MORE

Feb 06, 2015 | Ford Cars & Trucks

1 Answer

Daughters 2002 Hyundai Getz is stuck in what i think is second gear.


Worn Clutch plate or thrust plate.

Check if hydraulic Clutch
if so check clutch fliud level . Could be a faulty clutch master cyclinder in hydraulic system.

Jan 15, 2015 | 2002 Hyundai Getz

1 Answer

How do I check the valve lash on my toyota 5k engine with hydraulic valve lifters?


it is not necessary and impossible to do so as the lash is taken up by the hydraulic lifter operation. There will be no adjusting screws on the rockers for the adjusting purposes. If it is making aclicking/tapping noise similar to loose tappets and the engine has done miles then it is possible that either the rocker shaft and rocker bushes are worn or the hydraulic followers need replacing.

Dec 10, 2014 | Toyota Cars & Trucks

1 Answer

How do i rest abs light on hyundai getz even though diagnostic testing says there are no errors


You need a diagnostic meter capable of shutting off the ABS light. Have a repair shop do it.

May 14, 2014 | 2005 Hyundai Getz 1.6

1 Answer

We have a ticking sound in the motor. what could it be and what should we do


Hi, this sound is usually caused by a failed hydraulic valve lash adjuster. The part should be replaced as soon as possible to avoid damage to the camshaft. The problem adjuster must be identified and the camshaft must be lifted to replace the lash adjuster. Depending on the location of the particular lash adjuster, the valve timing belt may also need to be removed. This is a job for a mechanic, but if you have some experience with camshaft work, you may be able to do it yourself. Please let me know if you have questions and thanks for using FixYa.

jturcotte_954.gif

Jan 30, 2011 | 2003 Hyundai Santa Fe

1 Answer

I need the engine valve spec for a 1984 chevy 6.2 diesel. We are adjusting the valves.


VALVE ADJUSTMENTS All gasoline and diesel engines in this guide use hydraulic valve lifters, which require no periodic maintenance or adjustment. However, in the event of cylinder head removal or any operation that requires disturbing or removing the rocker arms, the rocker arms must be adjusted in order to position the pushrods to allow the hydraulic lifters to maintain zero lash. Refer to the valve lash adjustment procedure under Rocker Arms, earlier in this Section.

Aug 21, 2010 | 1984 Chevrolet K1500

1 Answer

Tapping Noise at idle 1994 Dodge Dakota 3.9L 5 speed manual


for v-6....3.9L

These engines are equipped with hydraulic lash adjusters designed to maintain zero lash at all times.

for 4 cyl...2.5 sohc
Valve Lash
Non-adjustable Dry Lash 0.024-0.060 inch.

for v8,...5.2---These engines use hydraulic lifters. No provision for adjustment is provide

Jun 04, 2009 | 1993 Mazda RX-7

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...