Question about Cars & Trucks

Open Question

Wat is the torque setings on a huhadia atos 1.1 mains bigend and head

Posted by on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

  • 5 Answers

SOURCE: need torque setings and tightening sequence for

stage 1 20nm,stage 2 30nm and then 90* and another 90*

Posted on Jun 27, 2009

  • 365 Answers

SOURCE: im looking for torque settings for my 2002 jeep

try ringing an engine reconditioner, he should have those specs for you at no charge

Posted on Jun 14, 2010

  • 1796 Answers

SOURCE: mitsubishi canter truck 4d34 torque settings

Most manuals I found do not cover diesel engines. There is a Peter Russek manual for your truck which covers diesel engines. Click on the following link to check the manual
THIS ARE THE SPECS FOR A 04 MITSUBISHI LANCER. Identifying Fastener Tightening Specifications Table ITEMS SPECIFICATIONS Roll stopper bracket mounting bolt69 ± 10 N.m (51 ± 7 ft-lb) Shift cable bracket mounting bolt19 ± 3 N.m (14 ± 2 ft-lb) Select lever mounting bolt19 ± 3 N.m (14 ± 2 ft-lb) Speedometer gear mounting bolt4.0 ± 1.0 N.m (35 ± 9 in-lb) Backup light switch32 ± 2 N.m (24 ± 1 ft-lb) Interlock plate bolt30 ± 3 N.m (22 ± 2 ft-lb) Poppet spring32 ± 2 N.m (24 ± 1 ft-lb) Control housing mounting bolt19 ± 3 N.m (14 ± 2 ft-lb) Under cover mounting bolt7.0 ± 1.0 N.m (61 ± 9 in-lb) Reverse idler gear shaft mounting bolt48 ± 6 N.m (35 ± 4 ft-lb) Clutch housing-transaxle case mounting bolt44 ± 5 N.m (33 ± 4 ft-lb) Front bearing retainer mounting bolt19 ± 3 N.m (14 ± 2 ft-lb) Select lever mounting nut12 ± 1 N.m (104 ± 9 in-lb) Stopper bracket mounting bolt22.3 ± 0.3 N.m (16.1 ± 0.2 ft-lb) Clutch release bearing retainer mounting bolt9.8 ± 2 N.m (87 ± 17 in-lb) Differential drive gear mounting bolt132 ± 5 N.m (98 ± 4 ft-lb)

Posted on Sep 30, 2010

  • 360 Answers


Go to a auto parts store (Pep Boys, Auto Zone, Advance, O'Reilly's, etc. ...they all have vehicle specific manuals for sale that will have a section on torque values.

Posted on Dec 26, 2010

  • 1 Answer


Fiat uno mia 1100 toque settings

Posted on Jul 24, 2011

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I need torque settings on 2.2 ford ranger tdci 2012 head bolts, mains and bigend bearings

hi lourens.
not sure if this link will help but have a look.
do not go into anything that has the word fixya next to it as it will only bring you back here.
torque settings on 2 2 ford ranger tdci 2012 head bolts mains and big end...

Jun 07, 2017 | Ford Cars & Trucks

1 Answer

What is the tappet clearance and torque setting for hyundai atos 1.1 2007

valve clearance is inlet .02mm hot. exhaust .025 mm hot cyl head torque is cyl head torque stage1 30-35nm stage2 60-70nm stage3 run engine for 15 minutes. stage 4 tighten further 70-75 nm

Dec 15, 2016 | 2007 Hyundai Atos 1.1

1 Answer

Torque specifications for head bolts mains bolts bigends for toyota mark 2 engine number 1JZ-GE2491

go on line -typr in torque specifications for toyota 1jz engine and there will be a pdf spec sheet of all the vehicle torque settings.

Dec 28, 2014 | Cars & Trucks

1 Answer

Torque settings

depends on your engine. If it's a VW air cooled flat 4, the mains which also ties down the engine casings, is torqued to 35 ft lbs and the cyl heads to15 ft lbs.
On more modern engines the mains can be torqued to 65 ft lbs, the big ends to 45 ft lbs and the cyl head to anywhere between 30 to 45 ft lbs.
A common remark among mechanics is to turn them till they strip, then a quarter turn back. Don't follow this rule.

Nov 05, 2014 | Cars & Trucks

1 Answer

Torque setings on bigends and mains on 1kr yaris engine

Main caps:
225 kg cm and rotate ninety degrees more.
Connecting rod bolts:
155 Kg cm and rotate further ninety degrees.

Oct 30, 2013 | 2006 Toyota Yaris 1.0

1 Answer

What is the torque setting of mains, bigends and cylinder head of 1zz Toyota corolla 140i

- Connecting rod (big ends). Tighten bolts in several steps. 1st stage 29 NM, 2nd stage, rotate further 90 degrees
- Main cap bolts (crank shaft). Tighten bolts in several steps. 1st stage 44 NM. 2nd stage, further tighten 90 degrees.

Oct 06, 2013 | 2005 Toyota Corolla

3 Answers

Chana star 1000cc:Torque settings,main bearing,bigend bearing &cylinder head.


Aug 06, 2013 | Cars & Trucks

2 Answers

Engine torque settings mitsubishi 4d32

im looking for information by a 4d32 Mitsubishi , help!!!!!! thanks

Apr 03, 2012 | 1988 Mitsubishi Cargo

2 Answers

Flywheel bolts torque settings

Check with your local auto parts store. Or buy a repair manual

Jun 07, 2008 | 1999 Volkswagen Golf

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

77932 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14403 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides