Question about Cars & Trucks

Open Question

Can fire ant bite cause a rash with pimple like eruptions on my arm-bicep under the original bite x 3.this is most unusual. can this happen @ day 4.the 3 original bites are almost healed up.

Posted by on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


SOURCE: clutch bite really low got

leaky slave or master cylinder,

Posted on Jul 19, 2008

  • 117 Answers

SOURCE: clutch is at high biteing point

The cables on these models are self adjusting so it could be stuck but more likely the problem is a worn clutch that needs replacing.

Posted on Apr 08, 2009

  • 77947 Answers

SOURCE: Self ADjusting Clutch Cable

Your car uses a hydraulic clutch, they are self adjusting and there is no way to adjust them provided, when the pedal engages near the top of its travel this means the clutch disk is worn out.

Posted on May 05, 2009

  • 1486 Answers

SOURCE: 2002 2.0L Passat petrol: Clutch biting point problem

your pressure plate is damaged.Replace cutch asseberly

Posted on Jun 12, 2009

  • 450 Answers

SOURCE: clutch bites high up on pedal movement

check clutch master cylinder rod adjustment and pedal height should be just higher than brake pedal. could try and bleed system also.
most hydraulic clutch systems have high take up points, adjust master cylinder rod, check for free play at top after adjusting if all that is O.K. then clutch plate may be nearly worn out but not slipping at this stage.

Posted on Jul 29, 2009

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

I am having a adverse reactions to Lidocaine patches....violent red breaks out from my knees to my stomach and new break out at arm pits......PLEASE HELP

not from this site
you should be back with the doctor to have the medication changed as that is where you get medical help

Oct 28, 2016 | Cars & Trucks

1 Answer

My mk 4 spit is turning over and firing with the ignition key open but shuts off as soon as I let the key go. Any ideas?

I'm thinking it's the switch itself since it does fire in the 'start' position. The contacts in 'run' position may have become worn, hence no current supply to ignition.. This is not unusual if the ignition key is combined with several others, placing extra weight on the mechanisim. This happens with air cooled Porsche 911's and older liquid cooled VW's..

Apr 30, 2015 | Triumph Spitfire Cars & Trucks

2 Answers

My mazda 3 diesel is surging when I first start her. What could be the problem?

It sounds like you might have a small fuel leak allowing the system to loose prime over time. check for wet fittings and pipes between the high pressure pump and the injectors.

Jul 26, 2014 | 2010 Mazda 3 1.6

1 Answer

Why did the wires to the alarm system burn?

water is a great conductor and probable caused short --thats why water and electricity dont mix

Aug 06, 2017 | Toyota Cars & Trucks

2 Answers

My son had a 1992 ford probe that had an engine fire 2 days ago( it's totaled), he had just gotten a new battery and had it installed at auto zone just a few days earlier, the firemen that put out the fire...

I doubt that Auto Zone could be held responsible. A lot could have taken place under the hood in a few days. And there's no way to really tell what caused the fire. Plus, if it was a total loss, how could anyone determine where the fire originated?

Dec 22, 2010 | 1992 Ford Probe

2 Answers

Unusual starting problem, Nissan sentra '96 GXE 179K

Probably not because the tool reads if the injector is getting pulsesw, not if it is sealing correctly when off. I'd try to take a look at the spark plugs to see if any have fuel on them after you crank once in no-start. "On the floor" likely would take longer because injectors are adding fuel while you are trying to remove it.

Mar 22, 2009 | 1996 Nissan Sentra

2 Answers

Is the engine busted? 2000 Chevy Blazer

no idea
take it to an accredited service center for a proper diagnosis and quote
initial cause was probably a lack of pre use inspection

May 24, 2017 | 2000 Chevrolet Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

15 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

77947 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14405 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides