Question about Cars & Trucks

Open Question

I have a Schwinn srb-1800 recument bike and the left pedal will not turn?

We have taken it apart and the magnetic brake will not release from the wheel.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 195 Answers

SOURCE: parking brake pedal goes to floor

Hello;
The parking brake cables may be stretched and in need of adjustment. Follow the cables along to a nut. Then you can tighten the adjusters up on both sides until you have the proper tension. Also make certain none of the brackets are bent or broken that the cables ride through.
Thanks;
RPM Northwest

Posted on Jan 19, 2009

Ad
  • 5 Answers

SOURCE: Left turn signal stops flashing when brake pedal is depressed.

there is a ground problem, most likely in the tail unit itself, but a ground problem is hard to find and easy to fix. reground the system, the turning unit, and the problem should stop. About the hazards, I don't know...... some times in older cars, that is the way it works. because the brake and hazard element in the bulb is the same and the old cars used a break in the power, but the new cars use a break in the ground. any way, chase the ground down first, it is usually the cause.

Posted on Feb 12, 2009

csmock132
  • 4669 Answers

SOURCE: 98 Chevy c2500 rear brake lock up

No axle gease at all on the shoes. Or brake fluid? Have you tried loosening the adjustment a turn.

Posted on Jun 14, 2009

  • 1 Answer

SOURCE: Hissing noise when releasing brake pedal

Sounds like your brake booster but can't be sure until I know what kind of truck or car you have....

Posted on Jun 27, 2009

  • 1 Answer

SOURCE: left from brake caliper sticks at times wheel gets real hot

You brake HOSE may have deteriorated, and is not allowing fluidto drain out of the caliper piston. I found out after a piston, caliper, two disks. The wheel would LOCK UP it got so bad.

Posted on May 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2003 Chevy Trailblazer brake pedal not releasing. When turning and brakes tapped briefly they continue to brake until complete stop. When stopped and foot off brake 10 sec delay before pedal releases


Sounds like your ABS unit on its way out.
with the engine off, pump the pedal till its hard. keep your foot on the pedal pushed down and start the engine. your pedal should become light and continue down to the "floor".

Jan 12, 2015 | 2003 Chevrolet TrailBlazer

1 Answer

What causes the break light swich to push, ive took apart the swich and can push it and break lights worked but when i put swich back on with clip it dose not work when i hit the break peddel


nothing, It doesn't work like that, when your brake switch is mounted , correctly , your pedal has a bracket on it that pushes the switch plunger in so brake lights are off. when you push brake pedal in, to stop vehicle, the switch plunger (spring loaded) comes out to turn brake lights ON ! get it ? when you release pedal it pushes plunger in, to turn lights OFF !

Jan 15, 2013 | 1997 GMC Sierra

1 Answer

Hummer H3 airbag light wont go off


Airbag light on in a Hummer H3 Dashboard???Here is the fix...
Start the engine of your car, set the parking brake, hold the regular brake pedal down with your right foot. Push down the parking brakepedal to its fully-applied position with your left foot. Now while you are still holding the regular brake pedal down. Quickly release the parking brake, Pull the bottom edge of the lever, located above the parking brake pedal, with the parking brake
symbol, directly rearward to release the parking brake. Make sure pedal snaps hard all the way back releasing the parking brake... If this doesn't work the first try, try it 3-5 times and it shall work... The airbag light will go off...


NOTE: The parking brake pedal is located to the left of the regular brake pedal, near the driver's door.
&

The parking brake lever is located above the parking brake pedal, with the parking brake symbol.

May 28, 2012 | 2006 Hummer H3

2 Answers

I have a 2004 Land cruiser and changed the right rear brake cyl and brake shoes . What is the proper procedure to bleed the rear brake system. Thank you for your help.


  1. Check the fluid level in the reservoir after bleeding each wheel. Add DOT3 fluid, if necessary.
  2. If the master cylinder was disassembled or if the reservoir becomes empty, bleed the air from the master cylinder as follows:
    1. Disconnect the brake lines from the master cylinder.
    2. Slowly depress the brake pedal and hold it.
    3. Block off the outlet plug with your finger, and release the brake pedal.
    4. Repeat 3 or 4 times.

  3. Bleed the brake starting with the one furthest from the reservoir and then the next furthest, etc.
  4. Depress the brake pedal several times, then loosen the bleeder plug with the pedal held down.
  5. At the point when fluid stops coming out, tighten the bleeder plug to 11 Nm (8 ft. lbs.), then release the brake pedal.
  6. Repeat until all the air in the fluid has been bled out.
  7. Repeat the procedure to bleed the air out of brake line for each wheel.
  8. Check the fluid level and add DOT3 fluid if necessary.

Aug 07, 2011 | 2004 Toyota Land Cruiser

1 Answer

My break light swithes on sometimes without me even pressing the breaks. The break light also sometimes stays on even when I have taken my feet off the break. I have tried changed the break light switch...


Did you adjust the brake light switch correctly? To adjust the brake light switch, first press the brake pedal down a few inches, then pull the switch plunger rod out of the switch toward the brake pedal arm, as far as you can without using excessive force. Next, return the brake pedal to the pedal stop position against the pedal stop and pull the brake pedal toward the rear to push the brake light switch actuating plunger rod into the switch housing limited by the travel of the brake pedal arm rear travel stop position. This procedure automatically adjusts the brake light switch correctly.
If the brake lights still don't turn off with the brake pedal released, check the brake pedal arm for sticking or binding that is preventing the brake pedal arm from returning fully to the pedal stop when the brake is released.

Feb 21, 2011 | 2002 Audi A4

3 Answers

My brake lights don't turn off, even when the engine is off.


Most vehicles brake lights work whether the engine is on or not. Check that the brake pedal is returning properly. See if there is a sensor under the dash that is engaged when pushing on the brake pedal. It may be on the pedal mechanism or on the front firewall. It may need to be pulled on. This will probably require a repair to correct the issue as it will probably happen repeatedly.

Mar 13, 2010 | 2005 Dodge Grand Caravan

1 Answer

Left turn signal stop when I apply brake. Then


i think the bulb is backwards or wiring is crossed

Aug 14, 2009 | 2000 Honda Odyssey

1 Answer

98 Chevy c2500 rear brake lock up


No axle gease at all on the shoes. Or brake fluid? Have you tried loosening the adjustment a turn.

Jun 14, 2009 | 1998 Chevrolet C1500

1 Answer

Brake lights


That plastic piece is the brake light switch.

Jan 12, 2009 | 1984 Honda Accord

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76673 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...