Question about Cars & Trucks

Open Question

Flashers & turn signals not working on John Deere 3203 tractor. All bulbs are good. There are NO fuses or relays in the fuse panel for flashers

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 373 Answers

SOURCE: turn signals wont work but flashers do

Hi.
On your 98 Dakota.
Is equipaded with a single Flasher.
If you replace all ready.
Check the FUSE # 10, 15 amp..
On the Fuse box. left side of Dash.
and the FUSE D 25, amp. On engine compartment Fuse box.
Check the proper funtion of the HAZARD switch.
Bacause if the Hazard switch is bad the turn signal don't will work. Match the OLD flasher with the New one.

If after of this still not work.
Remove the steering wheel cover, locate the Turn signal switch connector and with a TEST Light check power with the Key ON
12v. to the RED wire and PINK wire..
If you found 12v. check the connection with the switch.
If the connection is good. you will need to replace the turn signal switch.
But if you don't found 12v. You need to look a an open circuit.
And fix it..

I hope this help on your problem..
Thank you for use fixya...

Posted on Sep 01, 2008

  • 3 Answers

SOURCE: 98 Jeep Wrangler turn signals and flashers don't work

The tail lights on the 98 use the screws that hold the light to the body of the jeep to ground the lights. Chances are the wholes that the screws/bolts goes into have a coating of rust around them and are stopping the lights from grounding. This may not be the solution but you need to eliminate this from your list.

Posted on Mar 25, 2009

  • 1986 Answers

SOURCE: Brake/turn signals/flashers not working, fuses ok, what now?

There should also be a unit called the electronic flash module / unit. It should be somewhere under the driver's side dash.. unfortunately I do not know where in particular

Posted on Aug 13, 2009

localwonder
  • 6784 Answers

SOURCE: turn signals and emergency flashers do not work

The turn signal flasher assembly is located under the driver's side of the instrument panel, on the front of the fuse panel, or under the center section of the instrument panel in the relay/flasher block. This is ,basically, the controller for your turn signals.

Click here to view a picture of the flasher switch.

Posted on Nov 22, 2009

alicantecoli
  • 22095 Answers

SOURCE: No brake lights - good bulbs, good fuse, Flashers

renew the brake light switch it has two circuits inside it

Posted on Sep 17, 2010

Testimonial: "I can't believe how quick the response was, and it verifies what I suspected. I wanted another opinion before I purchased a new switch, Thanks!"

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What would cause turn signals,and flashers to stop working,and bulbs are good


bad earth to the ofending lights, burnt out flasher unit, worn switch. all assuming youv checked the fuse fisrt, after that check the flasher unit which should be in or near the fuse box and it will look like a rely so make sure youv got the manual or guide book befor you start pulling out the relays

Jul 30, 2014 | 1997 Mercury Mountaineer

1 Answer

My car signal stop funtion


have you checked the turn signal relay! It is above your left leg under the fuse access. under dash. do your emergency flashers work, because the relay is a combination relay for e-flashers and turn signals. if the flasher unit is ok, you may have a bad bulb or a short to ground.

May 17, 2014 | 1997 Dodge Grand Caravan

1 Answer

Blinkers dont work. flashers work


Most GM the blinkers and flashers have seperate relays. But if see your flashers work you know the bulbs are good. So there is one thing out of the way.

The turn signal relay should be a two prong relay on the interior fuse panel. The hazard relay would be one with three. The hazard relay may be on a "convienience" center which is usually tucked way up under the dash.

Sep 23, 2011 | 1994 Chevrolet Cavalier

1 Answer

TURN SIGNAL AND FLASHERS DONT WORK. CHECK BULBS ALREADY THEY ARE GOOD. WHERE IS THE FLASHER RELAY LOCATION .


I would recommend that you check your fuses, and the relay is in the fuse panel.

Mar 28, 2011 | 1992 Dodge Caravan

3 Answers

I have a 2000 ford explorer and both my 4 way flashers and turn signals are not working


check the fuses and both flasher cans,if not working then,u need to check the blinker switch

Dec 23, 2010 | 2000 Ford Explorer

1 Answer

Have a 1988 chevy truck; blinkers don't work. fuses are good, bulbs good. don't have power coming from fuse panel. flasher relay has been replaced


did u change the correct flasher?there are 2 flashers,the regular turn signal one and the 4way flashers,make sure u changed the right one,,,

Jul 07, 2010 | 1988 Chevrolet C1500

1 Answer

1998 taurus - turn signals were working - pushed the hazard lights button - hazards did not work and also now turn signals do not work


Check the fuse/relay panel for a blown fuse/relay. Also look at the turn signal flasher and the four way flasher located in fuse/relay panel for problem. If the fuses are good replace the flashers to correct the problem. Hope this will help you.

May 20, 2010 | Cars & Trucks

1 Answer

New bulbs, turning signals do not work...


Check the flasher located in the fuse/relay panel. Also check for a blown fuse as well. Remember this if the 4 way flashers are not working the turn signals will not either. To test the flasher before you remove it, turn the turn signal switch to either side and with your finger touch the top of flasher. If you feel a click from flasher then it's good and you will have another problem in the wiring. Hope this will help you.

May 15, 2010 | Cars & Trucks

2 Answers

1993 Dodge Shadow...left turn signal won't flash


If the fuses are good and the front and rear bulbs are good, change the flasher for the turn signals, even tho the right is working. If that doesn't fix the problem, it might be in the turn sgnal switch on the steering column.
If both bulbs are good for the backup lights and fuses are good, then the backup light switch, which is screwed into the side of the transmission has to bad.

Apr 12, 2009 | 1993 Dodge Shadow

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...