Question about Mercury Cars & Trucks

Open Question

How do I get to blend door actuator in 2005 Mercury Montego to replace it

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1 Answer

SOURCE: Blend door

ok first put you front seat down and back raise steering wheel . now lay on you back with you head in the drivers floor board. look up see 2 screws remove them and the panel they hold on . look to left main wire harness needs to be moved to the right , up and behind it is th blend actuator 7/32 socket to remove it then manually turn the white peg , total labor 30 min

Posted on Dec 15, 2008

  • 356 Answers

SOURCE: Change the oil on a 2005 Mercury Montego

Go to a automotive store and tell them you have a 2005 Mercury Montego and what engine it has if there is more then one model and get an oil filter and the oil. Put the car up on ramps and secure it making sure it won't roll back or fall while you are under it. get under the engine and look for the oil pan which should have a bolt in the bottom of it where you can drain the oil. Drain the oil in a proper container and then put the drain plug back in the pan. Then find the oil filter and unscrew it and remove it.. It could be full of oil so watch out and make sure the pan is underneath the filter. Wipe the base where the oil filter screws on and make sure the gasket from the old filter is not still on the engine. Get your new filter and take your finger and put it in one of your new containers of new oil and spread that on the gasket of the new filter. Screw on the filter until the gasket touches the base and then turn only a little more then a 1/4 to 1/2 turn tops. Do not over tighten the filter. Find out what oil the vehicle needs (probably 5-30) and look for the oil cap on a valve cover under the hood. It probably takes 5 quarts but check for sure in your manual or ask when you are at the automotive store. Put the oil in and put the filler cap back on. Now go start the vehicle and make sure you have oil pressure by either the oil pressure guage showing pressure or the oil pressure idiot light goes off and while running check under the car for any signs of leaks. If no leaks then back the car off the ramps and shut the car off on a level surface. Let it sit 10 minutes and check for leaks underneath the car and check the oil dipstick to make sure the proper level of oil is in the engine. Then you are set.

Always check your air filter when changing oil to make sure it is clean as that helps your engine run better and you save gas in the process. Good luck

It is also best to change oil when your engine is warmed up as well.

Posted on Mar 28, 2009

  • 236 Answers

SOURCE: Where is the blend door actuator located? Is it a

buried in the dash, about an 8 hour job.

Posted on Oct 13, 2009

  • 1 Answer

SOURCE: blend door actuator needs replacing does the

no it doesnt ... check out heatertreaters.net if you have to replace the blend doors .... but the actuator is directly behind the glove box...remove the glove box take out 3 screws and remove actuator and replace.....waa laa

Posted on Nov 25, 2009

  • 248 Answers

SOURCE: What do I have to remove to access blend door actuator

very lenghty process. too long to describe here....go to Bonneville Forums read the text and follow linked there at the bottom....very good and detailed....I'm doing that right now,,,,it is a bugger,

Posted on Apr 16, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of passenger side blend door actuator on 2006 mercury mountaineer auto controls, 6 cylinder


Temperature Blend Door Actuator - RH, EATC Removal and Installation
  1. Remove the RH floor console finish panel.
  1. Lower the glove compartment.
  1. Disconnect the RH temperature blend door actuator electrical connector.
  2. Remove the 3 RH temperature blend door actuator screws.
    1. Remove the RH temperature blend door actuator.
2006 2010 Ford Explorer NO Heat Passenger Temp Actuator Replacement same as mountaineer

Jun 19, 2017 | Mercury Cars & Trucks

1 Answer

Blend door actuator replacement 2005 2006 2007 mercury montego


Remove the glove box liner and you should be able to access it from there.

Apr 01, 2016 | 2005 Mercury Montego

1 Answer

I replaced the blend door actuator on my 2005 Tahoe on the rear A/C unit and it moves the actuator to its full range and then won't move?


In most cases once you replace the actuator, you have to calibrate it with a scan tool thru the computer.

Feb 18, 2013 | 2005 Chevrolet Tahoe

1 Answer

2005 mercury mariner clicking behind dash


This is the actuator for the AC/Heater systems temperature control blend door actuator motor drive, the blend door is sticking and the motor gears are jumping teeth. Very soon you will need to have this problem repaired as you will loose the ability to control the air temperature at the register air outlets.

Nov 06, 2012 | 2005 Mercury Mariner

1 Answer

Replace fuel filter on 2005 montego


You may need a certain tool for ford fuel lines to get the clips to come off. This job should only take about 10 min. locate the fuel filter,usually an in line. clip off either end to stop the flow of gas. quickly change one end at a time. replace with new clips.

Oct 14, 2012 | 2005 Mercury Montego

2 Answers

Heater blows cold air


Hi!
If the Temp. Selector Control is set to Heat and blows cold air, your Blend Door Actuator may be stuck or it is inoperative. The actuator is not fixable, if it fails, it must be replaced. Follow the instructions to remove and replace it.
  1. Disconnect battery negative cable from battery and properly isolate to prevent accidental reconnection.
  2. Remove the instrument panel.
  3. Disconnect the electrical connector from the blend door motor/actuator.
  4. Remove the four screws holding the blend door actuator to the plenum.
  5. Remove the temperature blend door actuator.
BLEND DOOR ACTUATOR CONNECTOR e8349ea.jpg

BLEND DOOR FASTENING SCREWS 9744710.jpg

Show your appreciation with a - 4 THUMBS - rating for answering your FREE question. Thank you for using FixYa.

Oct 07, 2010 | 2003 Mercury Grand Marquis

2 Answers

2003 mercury grand marquis LS heater does notr blow hot air, blower blows but cold air comes what is the problem


The blend door is stuck in cold position. That usually happens because the blend door actuator has failed.

You will need to test and replace the blend door actuator.

To replace the actuator you will need to take apart the dash and remove completely the instrument panel,d isconnect the connector, remove the four screws, remove the temperature blend door actuator and replace it.

The replacement is not a job for beginners, since you have to take apart the dash to access the actuator.

Regards.


Nov 18, 2009 | Mercury Grand Marquis Cars & Trucks

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

fordexpert

Level 3 Expert

5501 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...