Question about Cars & Trucks

Open Question

I have a 2001 chevy venture and I need to replace the crankshaft position sensor and cannot find it

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
shop242
  • 214 Answers

SOURCE: 2000 Chevrolet Venture multiple codes stalling and rough idle

Look for broke/ shorted wires on Crank sensor.. thanks

Posted on Mar 17, 2009

Ad
  • 135 Answers

SOURCE: Need to replace both crankshaft position sensors 2001 Cadillac

4.6 the twocrankshaft position sensors are located on the front of the block just above and to the left of the oil filter. not hard to replace.

Posted on May 19, 2009

ZJLimited
  • 17970 Answers

SOURCE: crankshaft position sensor location

1990 Chevrolet Cavalier 2.2L TBI 4cyl
The Crankshaft Position Sensor is located under hood, center, rear engine area, below ingnition coil pack and DIS module, mounted in engine block.

87c675c.jpg

Fig. 1: View of the CKP sensor-to-crankshaft reluctor relationship

Crankshaft Position (CKP) Sensor
A magnetic crankshaft sensor (Hall Effect switch) is used which is remotely mounted on the opposite side of the engine from the DIS/IC module. The sensor protrudes in to the engine block, within about 0.050 in. (1.27mm) of the crankshaft reluctor.

I really hope help you wuth this (rated this help). have a nice day, good luck.

Posted on Sep 25, 2009

Testimonial: "Awesome. Thanks."

emissionwiz
  • 77499 Answers

SOURCE: replace a crankshaft position sensor on a 1996

1st I need to know what engine you have, 4.0L or 5.2L V8.

Posted on Oct 02, 2009

  • 248 Answers

SOURCE: where are the camshaft and crankshaft position

crankshaft sensor is and the hormonic balance pulley and cam sesoor should b and the front of the motor toward the top. But to b sure u should get a book for u vehical

Posted on Mar 09, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace the crank shaft position sensor on a 2001 chevy Tracker V6 Lt 2.5L


Get underneath the vehicle and look at where the engine joins the transmission case.

The crankshaft position sensor will be located on the bottom or side .. usually towards the bottom..

It will be held in place with either a screw or small bolt. Undo the screw/bolt and withdraw the sensor. It's a straightforward job.

Photo below is a generic image of crankshaft sensor:


26063149-yytlcu2b3evmxr44xdn3gosb-1-0.jpeg You'll see the electrical lead/connector. Just disconnect the connector and remove the retaning screw/bolt

Jan 21, 2016 | Cars & Trucks

1 Answer

How do you replace crankshaft sensors on a 2000 chevy venture


Why would you change a crank sensor

It failed a test?

How was it tested?

No parts get changed just for something to do

Dec 22, 2012 | 2000 Chevrolet Venture

1 Answer

2001 Chevy Venture hard to start and grey smoke.


In the older cars, before all the emission laws added so much electronic garb, black smoke meant a fuel problem and grey smoke indicated a problem with internal engine parts like piston rings. Hope this helps.

Aug 02, 2012 | 2001 Chevrolet Venture

2 Answers

Were is the crankshaft position sensor located on 2001 chevy mali


It mounts in the side of the block near the crankshaft,it fits in a hole,going into the engine block.,look on the inside of the engine compartment ,on the firewall side,left of the pulleys,down low.

Mar 22, 2010 | Chevrolet Malibu Cars & Trucks

1 Answer

Engine problem


Re check the wire harness and pay attention to the crankshaft sensor. I hope that's a good start for now and good luck.

Apr 07, 2009 | 2001 Chevrolet Venture

1 Answer

2001 cheve venture (service engine soon) trouble light on


If ou fixed whatever happened during the oil change, the light will cycle off after about 3 drive cycles.

The check enine light just tells you that you are not meeting emissions right now. Only be concerned if it's flashing. That means you are sending unburned fuel to your catalytic converter whih will overheat and self destruct.

Look for a vacuum hose disconnected and check all the onnections to sensors such as, vehcile speed control sensor, mass air flow sensor, crankshaft position sensor, camshaft poition sensor, throttle position sensor, etc. Good luck.

Feb 27, 2009 | 2001 Chevrolet Venture

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14398 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...