Question about Mitsubishi Cars & Trucks

1 Answer

Yes,this is Rusty again ,how do i check my wiper moter to know if its good or bad on the mitsubishi

Or, could it be the switch,it squirts water on windshield,but thats all

Posted by Anonymous on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Top Expert:

    An expert who has finished #1 on the weekly Top 10 Fixya Experts Leaderboard.

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

  • Mitsubishi Master
  • 21,367 Answers

If you connect 12Volts directly on the motor, it will either work, meaning you probably have a blown fuse or it will be dead so will need new brushes or replacing.

Posted on May 16, 2017

Testimonial: "Thank You so much."

  • 1 more comment 
  • JonSnell Electronic
    JonSnell Electronic May 16, 2017

    Might be but if you go straight to the motor and work backwards you will soon find the fault.

  • Anonymous May 16, 2017

    it was a short, I traced it down, thank you very much JonSnell

  • JonSnell Electronic
    JonSnell Electronic May 17, 2017

    My pleasure.

×

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Front wipers stopped working....checked fuse ok...replased moter still does not work....


use a voltmeter and stop guessing, please.....
do you have 12vdc to the motor?
id bet not, so work backwards from there./
the FSM covers all this, get one
or login to alldata.com an read the wiper schematic.
fues that look good can be bad, again, that DMM voltmeter switched
to low ohms NEVER lies when you test a fuse
it reads 0 ohms good, zero ohms. if infinity its bad. (hair line cracks in fuse)

Feb 01, 2014 | 2007 Honda Odyssey Touring

1 Answer

Wipers not working..2003 Lesabre


Due to your first sentence, your problem sounds like it is in the actual switch. If it were a bad motor you would have experienced it stopping in the "on" position.

Mar 17, 2012 | 2003 Buick LeSabre

2 Answers

Front windshild wiper is not working but back ones are. what is my problem?


The fuse could be blown, or the motor could be bad, or the switch may be bad, or the wiring in between.

Oct 12, 2010 | 2001 Ford Windstar

2 Answers

I have a 1987 cadillac eldorado. The windshield wiper module went out yet again. The past itself is discontinued. I am not extremely car savy, and since the part is no longer being made, would like to know...


just a thought, try contacting auto recycling center(scrap yard) quite often you can find someone who can rig up something for ya, i know from experience with having to deal with unavailble parts in my years

May 23, 2010 | 1987 Cadillac Eldorado

3 Answers

Wipers do not work. i replaced the wiper switch and checked the fuses ,The red wire to the wiper moter has power ,how do I know if the wiper moter is defective?


there are usually two hot wires going to the wiper motor .. also a ground strap that may be bad ... one of the hot wires is always on if the key is on ... that for homing the wiper blades when you turn them off .. the other power input is from the wiper control circuit .. its only on if the wiper switch is turned on .. if you have power on the homing input then that wont do anything unless the wipers are not in home position .. if you have power to the "run" wire of the motor and the ground is good then the motor should run unless its defective .. you can put a jumper cable from the ground of the wiper motor to the engine block or battery neg, to check if the ground wire is causing the trouble .. that happens frequently in some models but not sure about your E250 ...

Oct 04, 2009 | 2002 Ford E250

1 Answer

My Kia 2003 rio front windscreen water not working


Take off the pipe at the pump then use the washer switch and see if the water sprays out. To check if the pump is working you will need someone to use the switch while you hold your hand on the pump you should feel or hear the pump working. If the pump is going but no water spraying blow back through it and try again. If it dosent work then you will probably need a pump.

Sep 15, 2009 | Kia Rio Cars & Trucks

1 Answer

Screen washers(front and rear) not working


Quick test since you can hear pumps running: Open hood. Look for a rubber hose going up from engine compartment to underside of hood. This should split somewhere if there are two washer jets on your hood, or else they go to your wipers and squirt directly off them, right? There will be a spot close to where this hose leaves the eng. comp. and joins with the hood that uses a splice connector. You can disconnect the hose here with some wiggling, and hit the squirters again to see if water is at least coming out of this primary hose. Yes? Good then the clog is at the jet end, or squirter end. Use a tiny piece of wire, like a bread tie without the insulation, and poke into the hole of the jet and try to clear out the dirt, or mineral deposit, dried soap scum, whatever. Now squirt again. Should start to clear out, or use compressed air and blow through jet. If your clog is not at the squirting end, follow the hose down to the little pump at the side/bottom of your juice bottle. GOod luck, and don't use too much additive, it clogs easier. Also don't use tap water if you get a lot of scale from hard water. THis will clog, too. Good Luck, TT

Feb 11, 2009 | Ford Focus Cars & Trucks

1 Answer

380 ES Mitsubishi 2006 model door window control


It possably isnt the switch it maybe the motor itself if you open the door panel and disconect the moter run 2 wires to the main battery becarefull because when you do this the motor may or may not work if the window goes up or down when you do this then your moter is good if not replace motor otherwise switch your wires from one switch to anouther that you know is good and try to see if it works then your switch may be bad.. do to the drivers window being used the most the switch or motor will go bad sooner then the others

Jan 25, 2009 | 1992 Mitsubishi Diamante

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

40 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8152 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...