Question about Cars & Trucks

Open Question

2003 nissian alitma 2.5 won't turn over tryed to turn crank shift and will not move???

Wheel wheel Fly wheel will not turn

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 78267 Answers

SOURCE: When you press the shift

If the light is continuing to flash the 4X4 is not engaged, most likely the motor that engages it on the transfer case is either stuck or defective.

Posted on Nov 28, 2008

Ad
  • 4 Answers

SOURCE: Steering wheel and shift lever locked, key wont turn.

Try a different key if possible, sometimes key wears down.

Posted on Jan 16, 2009

  • 14036 Answers

SOURCE: cant move transfer case shifter from 2 to 4 wheel drive

go to car wash spray back wheels enough to remove dirt.

Posted on May 02, 2009

  • 3600 Answers

SOURCE: my fly wheel to the air conditioner dont move on

There is no fly wheel on the AC compressor, however there is a clutch assembly that in gages and dis in gages when the Ac is turned on, if it does not spin when the A/C is no it is most commonly caused low refrigerant in the Air conditioning system. The system will have to be tested for leaks and repairs made and maybe a low pressure switch replaced in order to fix this.

Posted on Sep 28, 2009

  • 244 Answers

SOURCE: when clutch pedal depressed clutch does not move

in a car this 'new' prob. hydraulic. check clutch fluid reservoir- should be near brake fluid res.- will be smaller- if fluid is low, or empty- may be clutch master cylinder, or clutch 'slave' cylinder is leaking. check for leak under car, should smell like 'brake' fluid. if your brake master- both reservoirs are to the full line, and there's fluid under car, close to where clutch master is located, or near front of , or side, of tranny- then it's a clutch problem of some kind (as if you didn't already know this!!) relatively new vehicle (by my standards!), should have hydraulic clutch.
do you mean- when you depress the clutch pedal, it goes to the floor, and you can't shift into any gear??
should have asked this first! front wheel drive or rear? i'll guess front wheel drive. may have hyd. fluid leak in master or slave. (apologize for 'terms', but as 'male & female connectors', it's traditional, non-racist and non-sexist nomenclature!!) gotta' be careful, in the 21st century!! if there are, as i stated previously, 2 similar reservoirs, close to each other, then you prob. have hydraulic clutch. may need 'master' rebuilt, or replaced, or 'slave' replaced-it can be rebuilt, but prob not cost effective!
sorry to be 'long-winded/ texted', good luck!

Posted on Oct 23, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Key won't turn, won't shift from Park


My 2003 Saturn l200 2.2 ecotec did this when the battery was dead. Put some juice on the battery, then the car came out of park, and I was able to remove the key. To the car, there's a vast difference between a sluggish battery and a dead battery. It may have enough amps to crank it, but it wont start w/out full output from the battery.

Apr 12, 2013 | 2004 Chevrolet Cavalier

1 Answer

2000 olds alero cranks then makes a metal grinding sound and won't start


You need to have your flywheel: replaced.Your starter motor engages against the fly wheel at the back of the motor. Every time your motor stops it tends to be in the same few positions (just the way things work) so there is more stress on some parts of your fly wheel than others. Because of this the teeth wear out on the fly wheel which means the starter can correctly engage on the fly wheel which is the grinding noise.

Jan 18, 2013 | 2000 Oldsmobile Alero

1 Answer

My steering wheel locks up when I put it in park, and when I try to restart it, it won't crank. The key won't turn. What do I need to do?


grab the steering wheel and turn it left or to the right and sometimes you might have to put a little effort in it but one way the steering wheel will move about 1-2" and as you are moving it with one hand take the other hand and turn the key and it should turn a lot easier.this is a common thing and if you can try to have the wheels straight and try not to use the steering wheel to get in or out of the vehicle and the wheel should not lock and make it so hard on you.you have to use both hands at the same time one moving the wheel and the other one turning the key but start moving the wheel in the in direction that it moves the most then turn the key.

Jun 17, 2011 | 1999 Toyota Sienna

1 Answer

1998 ford f150 xlt floor shift wont move to shift to 4 wheel low or high


your going to have to get under it to see if it is gummed up. Spray penetrating oil liberally on those connecting rods and try to move it. Remember,,,,no matter what your manual says or the dealer that squawks about 4 wheel on the fly... come to a stop, put it in neutral then shift in to 4 wheel.

Dec 31, 2010 | Ford F-150 Cars & Trucks

1 Answer

Im replacing timing belt on 92 camry 30 v6 w/auto trans. i cannot breakloose he crankshaft balancer/pulley bolt. Are the threads lefthanded?is there any easy way to loosen this bolt without the crankshaft...


the fly wheel access is right there at the starter. it is a little piece of metal.remove it to gain access to the fly wheel or get someone to hold the crank pulley.you will also need a wheel pulley to remove the crank pulley

Jun 27, 2010 | 1991 Toyota Camry

1 Answer

I cannot get the timing marks on Crank and fly wheel alinged


to be honest it not as easy as it sounds to line them both up,,,,you may need to use a locking stud to do this,, and i have seen engines that just wont line up even to half a tooth out,,, but they run just fine anyhow, its all down to just how good the pullys were cut and marked

Feb 16, 2010 | 1994 Volkswagen Jetta

1 Answer

I have a 2009 CRV, and a bout once every 10 start ups when I turn the key to start the car I will hear a squirting sound, and it sounds like it is coming from the ignition. When this happens I generally...


Without hearing it I would only be guessing, however I believe starter solenoid is a good guess.
When you turn the key the first position it applies power to the vehicles ignition coil and other operational components. The second position applies power to the starter solenoid which moves the starter gear against the fly wheel so the starter motor can crank the engine to start the combustion process. If the solenoid does not move the small gear against the big gear you will hear the starter motor running with no resistance producing a high pitch whine. Some of the gears could be missing on the fly wheel but it would not start unless you physically moved the vehicle forward to manually move the fly wheel.
Therefore, I would have the starter (starter and solenoid are usually together) checked or replaced. If you have some mechanical knowledge you could do it yourself with minimal tools. I believe turning the key back is not helping you. You just need to turn off the ignition and try to start it again. Sooner or later the solenoid will fail completely and not work at all. I would not want to be stranded so I would fix it soon but it could work intermittently for a while.

Jan 13, 2010 | 2003 Chevrolet Impala

1 Answer

1993 4X4 BLASER 4WHEEL DRIVE


Your blazer is equipped with a shift on the fly four wheel drive. That means that at speeds less than fifteen miles per hour you can shift into or out of four wheel drive by simply pushing the four wheel high button. If you wish to shift into four wheel low. Stop, put the transmission into park or neutral, and push the four wheel low button. Same procedure for shifting back out. Never shift into or out of four wheel low while moving. And be careful in four wheel low. At full throttle your still barely moving, you don't want to blow your engine up!

Dec 31, 2008 | 1994 Chevrolet S-10 Blazer

3 Answers

Can,t get truck out of 4x4 low range


try putting your truck in neutral and then shifting into 2 wheel drive shift on the fly does not apply to 4 low only 4 high and on electric shift models it wont shift unless your ****** is in neutral.

Aug 26, 2008 | 1999 Ford F250 Regular Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

78267 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14405 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...