Question about Cars & Trucks

Open Question

What color is the wire that controls reverse code po736

Posted by on

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 22 Answers

SOURCE: reverse light wire code or color?

PLEASE UNDERSTAND that if you mess with any of the lighting on this vehicle it could cause the control module for the lighting system to malfunction and go out and this part the last time I replaced one was$970.00.

Posted on Sep 12, 2009

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2006 Pacifica touring and the following error codes: po700, po562, po736; po732, po731 and po,720 and po480. Can you tell me what I need to fix this?


With that many codes and those specific codes I would suggest finding a reputable transmission shop. I suspect either a wiring issue or a bad trtransmission control module. A good shop should be able to determine which in just a couple hours or so.

Oct 27, 2016 | 2006 Chrysler Pacifica Touring

1 Answer

Transmission 42le wount shift in to drive cod po731 and po736


go to that link , you'll get all universal codes description .


http://www.obd-codes.com/trouble_codes/



hope to help.

Nov 12, 2015 | 1996 Dodge Intrepid

1 Answer

Wiring for reverse switch on a 2008 ford expedition


You probably didn't do anything to the wiring ,relay contacts maybe stuck closed ,Check the relay or have it check for DTC'S
Transmission Control Module (TCM) Diagnostic Trouble Code (DTC) Chart DTC Description Action P1910 Reverse Lamp Control Circuit/Open Go To Pinpoint Test U . P1911 Reverse Lamp Control Circuit Low Go To Pinpoint Test U . P1912 Reverse Lamp Control Circuit High Go To Pinpoint Test U .
Principles of Operation
The transmission control module (TCM) sends gear status information to the PCM over the communication network. When the transmission is in REVERSE (R), the TCM energizes a relay which supplies voltage to the reversing lamps.

Oct 18, 2017 | Cars & Trucks

1 Answer

Pulled this code off my 05 lancer po736 what does it mean


Here is the definition for the code.

P0736 MITSUBISHI Description This diagnosis monitors actual gear position by checking the torque converter slip ratio calculated by Transmission Control Module (TCM) as follows:

Torque converter slip ratio = A x C/B

A: Output shaft revolution signal from revolution sensor
B: Engine speed signal from Engine Control Module (ECM)
C: Gear ratio determined as gear position which TCM supposes
Possible causes - Low transmission fluid level
- Dirty transmission fluid
- Shift solenoids
- Transmission mechanical problems
- Transmission hydraulic control circuit
Read more: http://engine-codes.com/p0736_mitsubishi.html#ixzz27FemXvl5

Sep 22, 2012 | Cars & Trucks

1 Answer

What is the code po736


Hi Greg:
DTC P0736 - Reverse incorrect gear ratio

The clutch pressure control (PC) solenoid 2 flows fluid to the 3-5-R clutch when commanded OFF and exhausts fluid when commanded ON. The clutch PC solenoid 2 regulates the transmission fluid pressure to the 3-5-R clutch. The transmission fluid pressure (TFP) switch 1 Opens (High) under fluid pressure and closes (Low) when no pressure is present. The transmission control module (TCM) calculates gear ratio based on data from the automatic transmission input speed sensor (ISS) and the output speed sensor (OSS). The TCM compares the known transmission gear ratio to a calculated gear ratio for each commanded gear.

Circuit/System Verification:
Operate the vehicle to induce a shift from second to third gear while observing TFP Switch 1. Perform this action 2 times. The TFP Switch 1 should change states from Low to High. If the TFP Switch does not change states and no other DTCs set, replace the control solenoid (w/body and TCM) valve assembly. If any other DTCs set, diagnose that DTC first.
Operate the vehicle to obtain sixth gear 2 times and then check for DTCs other than DTC P0736.If any other DTCs set, diagnose that DTC first. If no other DTC sets, continue on with diagnostics.
Operate the vehicle by shifting from Park to Reverse, then while in reverse, operate the vehicle with the calculated throttle position greater than 8% for 5 seconds, perform this maneuver a minimum of 3 times. If the DTC P0736 resets, go to Component Testing.

Component Testing:
Perform the line test procedure.
Inspect the check ball 5 for possible sticking or damage. If you found a concern with this check ball, repair the concern.
Inspect the shift select valve 3 for sticking or damage. If you found a concern with the shift select valve 3, repair or replace the valve or valve body.
Inspect the R-1 (Low and Reverse clutch) assembly for wear or damage. If you found a R-1 assembly concern, repair or replace the R-1 assembly as necessary.

Hope this helps; also keep in mind that your feedback is important and I`ll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using FixYa, have a nice day.

Dec 29, 2011 | 1996 Dodge Caravan

2 Answers

I bought a 1998 mitsubishi eclipse and the check engine light came on we hooked up the machine to diagnos it and we got 2 codes po700 and p1784 . we are wondering what the codes mean and how to fix the...


DTC 1784: LOW-REVERSE PRESSURE SWITCH
1.Remove transaxle relay from connector. Turn ignition on. Install scan tool and observe low-reverse pressure switch condition. Apply battery voltage to transaxle relay connector terminal No. 8. If low-reverse pressure switch stays off, go to next step. If low-reverse pressure switch turns on, go to step 4 .

2.Raise vehicle enough to allow drive wheels to spin freely. Test low-reverse clutch hydraulic pressure. See HYDRAULIC PRESSURE TESTS under TESTING. If low-reverse clutch pressure test is not within specification, internal transaxle failure exists. If low-reverse clutch pressure test is within specification, observe scan tool.

3.If low-reverse pressure switch turns on, trouble code is intermittent. Check wire harnesses and connectors for damage or poor connection. If low-reverse pressure switch does not turn on, replace solenoid and pressure switch assembly. Recheck trouble codes. If trouble code resets, replace TCM.

4.Check and repair wiring harness between transaxle relay connector and solenoid and pressure switch assembly connector. If wiring harness is okay, check wire between TCM connector terminal No. 10 and solenoid and pressure switch assembly.

5.If wire between TCM connector terminal No. 10 and solenoid and pressure switch assembly is okay, check TCM and solenoid and pressure switch assembly connectors. Repair connectors as necessary. If connectors are okay, recheck trouble codes. If trouble code resets, replace solenoid and pressure switch assembly. Recheck trouble codes. If trouble code resets, replace TCM.

P0700-The Transmission Control Module (TCM) monitors the malfunction of sensors and actuators relating to transmission control. When the TCM detects a malfunction with the control, a signal is send to the Engine Control Module (ECM) to trigger the Engine Light or Service Engine Soon light. The ECM stores the P0700 code and it means the TCM detected a malfunction with the transmission controls.

I would try disconnecting he battery and letting it sit for 5 minutes, then hook it back up to see if they return-the 700 code is probably related to the 1784 code, that seems to be your main issue.

Jun 06, 2011 | 1998 Mitsubishi Eclipse

1 Answer

1999 grand car. not shifting out of gear ,service engine light 0n


Try cleaning the throttle body. Does it do it more when it is warm outside?

Jul 03, 2010 | 1999 Dodge Caravan

1 Answer

Reverse light wire code or color?


PLEASE UNDERSTAND that if you mess with any of the lighting on this vehicle it could cause the control module for the lighting system to malfunction and go out and this part the last time I replaced one was$970.00.

Sep 10, 2009 | 2004 Volkswagen Touareg

2 Answers

Transmission codesp0700 and po736


visit http://www.troublecodes.net/neon/ for all code interpretations.

Rate this fixya.

Jul 11, 2009 | 2002 Dodge Neon

1 Answer

Reverse parking light wire color coding for Honda civic 02


Check the wires with the car in reverse and the key turned on, use a meter. On cars the black is usually the ground but you need to check to be sure.

Mar 28, 2009 | 2002 Honda Civic

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...