Question about Cars & Trucks

1 Answer

Do i need to take off any pulleys to get my cylinder heads off my 2003 3.1 chevy malibu

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    Visited the website for 3 consecutive days.


    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 154 Answers

Why do u want to remove heads???? if you don't know what you are doing... please don't mess with it you WILL be looking BIG dollars for someone who knows how...

Posted on May 16, 2017


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How to remove and replace the ignition lock cylinder on a 2003 malabu indash

Remove covers and there should be a little pin you push in which allows the barrel and keys to come out.( use a piece of wire to hold the pin in).

Jul 28, 2014 | 2003 Chevrolet Malibu

1 Answer

Po301 on chevy mzlibu 2003

code po301 refers to cylinder 1 misfire detected===causes--engine mechanical fault ( head gasket , cracked head , bent/burnt valves) ---wiring (HT lead, distributor cap or individual coil)--ignition / fuel ( injector and wiring)ECT/MAF sensor---ECM
Go for the cheapest fix first.

Jun 25, 2014 | 2003 Chevrolet Malibu

1 Answer

Serpentine belt 1999 chevy malibu is slipping off cranshaft pulley

Make sure that the belt is fully seated in ALL pulleys, if it still slips off, then you have a pully that is bent, or out of alignment.

Dec 04, 2013 | 1999 Chevrolet Malibu

1 Answer

Redoing head gaskets on 2003 Chevy Malibu. Can't

you can call Auto Zone or go to their web site and get the right specs,I've always use their web site

Oct 31, 2012 | Cars & Trucks

1 Answer

Overflowing from expansion tank on a 2003 chevy malibu

Have a cylinder leakage test performed to check your head gasket. It dosn't have to overheat to have a head gasket problem. A leakage test checks if looseing combustion gases to the cooling system which would presurise the system higher than normal which causes the tank to overflow.

Sep 30, 2012 | 2003 Chevrolet Malibu

1 Answer

Replace power steering pulley on 200 chevy malibu

GM power steering pump pulleys are a pressed on type with an"interference" fit-the hole is .001" smaller than the shaft.You need a puller/installer tool.I bought one for about 30 bucks at NAPA,you might be able to rent one at an auto parts store.The tool clamps the pulley nose and has a screw to push the shaft out.(some Chrysler alternators use the same design).

Sep 06, 2012 | 2000 Chevrolet Malibu

1 Answer

My 2003 Chevy Malibu 6 cylinder seems to be losing power from time to time. I've noticed it uses a LOT more gas than it use to even on very short trips. When driving even on a flat road it seems t

Check with the auto parts store to see what the fuel sensor looks like, It should be accessible and I have seen those go on the smaller chevys like aveo.
Look up on internet replacing gas recirculation sensor on google

Aug 12, 2017 | 2002 Chevrolet Malibu

1 Answer

2003 Chevy Malibu where is the coolant temperature switch

2.2L (L61) Engine
The Engine Coolant Temperature (ECT) sensor is located just to the left of the exhaust manifold in the thermostat housing between the two coolant pipes.

3.5L (LZ4) & 3.9L (LZ9) Engine
The Engine Coolant Temperature (ECT) sensor is located on the left cylinder head at the rear. It is just above the transaxle mounting bolts.

Hope helps (remember to rate and comment this answer).

Sep 19, 2011 | 2003 Chevrolet Malibu

1 Answer

Where is the head gasket on a 2002 chevy malibu

the head gasket is between the cylinder heads and the engine block

Sep 14, 2010 | 2002 Chevrolet Malibu

1 Answer

1997 Malibu torque Specifications

exhaust to cylinder head nuts 11 ft lbs
exhaust to cylinder head studs 97 in lbs
flywheel 22 ft lbs

Please rate this a fixya if this answers your question. Thanks!!


Sep 12, 2008 | 1997 Chevrolet Malibu

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

14445 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides