Question about Cars & Trucks

1 Answer

How can reset or secan car computer sysetem ?

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that gotĀ 5 achievements.


    Visited the website for 3 consecutive days.


    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 146 Answers

With a code scanner to read error codes. reset by disconnect battery for 5 minutes.

Posted on May 15, 2017


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How do I reset the computer to a 2004 crown victoria

I take it you changed the computer. Or why would you reset the computer that was in the car. If you replaced the computer with one specifically the same part number the computer should not need reset. If you are talking about resetting miles, that won't happen.

Oct 01, 2015 | Cars & Trucks

1 Answer

Computer reset on 2000 buick

Test the coil pack for cyl #3 first. A bad coil will cause the computer to give that code. To reset the computer remove both battery cables and touch them together for a minute or two, then reinstall them and then go drive the car for more than 20 minutes in traffic, stop and go so the computer will relearn inputs from all the engine sensors.

Jan 12, 2018 | 2000 Buick Century

1 Answer

Las bandas del motor chillan mucho< como puedo ajustarlas? por que no muestran un diagrama y metodo para el ajuste.

la solucion cuando las bandas chillan mucho es porque no estan bien ajustadas o muy viejas para ajustar las bandas revisa que el alternador tiene los tornillos para ajustar tambien el diagrama no te servira porque las bandas lla estan instaladas algunas veces cuando llueve y se mojan las bandas chillan mucho pero cuando se secan el chillido desaparece dos o tres dias despues buena suerte

Aug 25, 2011 | 1995 Isuzu Rodeo

2 Answers

Air conditioner only blows cool while driving. When car is idle it blows heat. Does this mean there is a leak in the line or is a new compressor needed?

sounds like a low charged to me the leak could be line or just about anything
including compressor look for residual oil on a/c sysetem will somtime indicate the leak
but sniffer the best tool to use to detect or have it dye injected and blacklighted

May 25, 2011 | 2005 Chevrolet Equinox

1 Answer

Oil is leaking in my denso a/c compressor

you will need to replace the compressor has i was never able to get replacment seals
also equipment needed to performed this repair is more then a replacment compressor
1--- have sysetem evacuated from remaining freon
2--- replace compressor per supliers information
add recomended oil if stated by supplier
replace affected o-rings or matting gaskets
3---have system nitrogen pressure tested for leaks
4---have it vacumed and recharged

May 21, 2011 | Toyota Passenger Cars & Trucks

1 Answer

Where is computer reset buttton for 2003 dodge stratus rt? I had heater core changed and everything worked fine until we took dash off and put it it wont start? It tries to but acts like not...

There is not a computer reset button installed on the car anywhere you need to have a computer that connects to the ecu on the car (the cars computer) with the computer attached you can reset codes or reset the computer.

Jan 16, 2011 | 2003 Dodge Stratus

1 Answer

Need to reset computer to start car or it won't start.

to reset the computer just take off a terminal on your car battery for 15 minutes, this will reset the system, if you have a standard stereo you need to remember or know the code incase it locks you out and asks you for one after.

Jun 20, 2010 | 2002 Nissan Sentra

1 Answer

My power steering went out while towing a trailer and now my brakes don't work either.....?

all on one sysetem the pump runns ur brake system to need to replace pwr steering system

Mar 28, 2010 | 2001 Chevrolet Silverado 2500HD

1 Answer

Codes need to be reset in my cars computer?

if you had it replaced it should have already been set however you can reset your cars computer by taking the positive battery cable off the battery and waiting 2-3 min and then touching the positive cable from the car to the negative cable which is still attached to the neg post on the battery for about 5 sec and the hooking it back up. that will reset the computer which would configure any new sensors. when the computer reads a bad code it bypasses that sensor so your car will run. it wont run to the best of its ability though - that's why you didn't pass an inspection. when you replaced the sensor the computer didn't notice because it already stopped reading that sensor when it went bad and doesnt know about the new one. when you reset the computer as i told you then it will read the new sensor and work properly.

Mar 30, 2009 | 2003 Honda Accord

1 Answer

Fuel sysetem

There is a lift pump in the fuel tank

Sep 05, 2008 | 1985 Ford LTD

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

16 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

77932 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14403 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides