Question about Cars & Trucks

Open Question

Clicking noise in somewhere in engine won't start or stay running idle unless I'm giving it gas?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

USfalcon
  • 175 Answers

SOURCE: Corolla repair manual

can y tell me what enigne size ?

Posted on Mar 23, 2009

mrgreenz
  • 962 Answers

SOURCE: 1997 Mazda Protege: Engine has clicking noise when idling.

Check to see if the valve lifters are not making the noise. Turn on the engine and rev it up to about 1500 rpms and see if the clicking is coming from the valve cover area.

Posted on Apr 05, 2009

ronaldo_ross
  • 1056 Answers

SOURCE: after re-connecting battery on 2000 Galant engine

Yeah thats what they meant, just don't idle it too high. If the problem don't go away, read it with an OBDII scanner. That will give you what the problem is.

Posted on Jul 03, 2009

  • 18 Answers

SOURCE: engine starts but will not idle, i give it gas but will not sustain in running afyer 2 seconds engine dies

check all spark plugs and wires also check mass air flow senser located on intake tube if all is still in good working condition check the throttle position sensor if that is good then it may be your fuel pump please update when possable.

Posted on Aug 07, 2009

  • 4 Answers

SOURCE: starts but dies as soon as i let off the gas wont

replace the gas filter just follow the gas line of the carb it should be easy to find

Posted on Feb 07, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My Durango starts if I give it gas and stalls when I let off the gas won't idle, help what to look for?


My car dies when I let off the gas - CarGurus




www.cargurus.com > Questions > Dodge > Durango












CarGurusDec 5, 2012 - My car dies when I let off the gas - I have a 2000 Dodge Durango SLT, I bought a month ago. I noticed it had a slow start but it still started and ran fin... ... Also, the oil pressure was high until it could idle by itself then it was back to normal. ... sometimes if you give it more gas it stays running but now it won't ...




dodge dakota idling and dying - CarGurus




www.cargurus.com > Questions > Dodge > Dakota












CarGurusApr 12, 2011 - dodge dakota idling and dying - My dakota will start then idle down and die. I can pump the gas and it will stay running but if i hold the peddle down or . ... thatdies on me at stop signs and when I take my foot off the gas pedal. .... and truck pops..misses and runs like crap and wont stay on unless i give it gas, ...




Truck starts but won't stay running...?? - Dodge Dakota Forum




www.dodgedakota.net/boards/v8/4240.html











Aug 9, 2003 - 21 posts - ‎20 authors

Dec 21, 2015 | 1999 Dodge Durango

1 Answer

Car wont stay running when foot off gas


sounds to me like your catalytic converter may be clogged.

Feb 17, 2014 | Ford Escape Cars & Trucks

1 Answer

My 97 Dodge ram Van won't stay running.


Unless the vac leak is very large, it would not keep the engine from idling.
The computer controls idle speed by regulating how much air enters the intake thru the throttle body by use of the idle air control valve.
The throttle body could be gummed up, or the idle control valve may be faulty.

Feb 19, 2013 | Cars & Trucks

1 Answer

My 03 chevy monte carlo has a po102 code and I know the mass flow sensor connector is bad but will this cause the battery to drain for no reason? I hear a clicking noise coming from the gove compartment...


If you have a light in the glove compartment that might be staying on. I would start pulling fuses one at a time until the clicking stops. Pull a fuse, still clicking, put it back and pull another. Repeat until you find the circuit causing the problem. That will narrow down where you need to look.

May 13, 2017 | 2003 Chevrolet Monte Carlo

1 Answer

98 Expedition..5.4L 4WD..coded bank 1 bank 2....O2 sensors..LEAN....replaced both..no change..still same codes..now it won't stay running. Tried to code again..won't run long enough to get a c


Really sounds like a vacuum leak. Lean code could still be accurate. Screaming idle usually means air is getting into engine. Ruptured EGR diaphragm would vent air. Brake booster could vent air. A lot of air will show lean mix.

You may have to use different methods to test vacuum. Some use vacuum gauge to test egr and lines which dead end into solenoids. Other tests use water spray or propane gas to draw in and change rpm. You are at a disadvantage if engine does not run.

Crankshaft sensor helps set fuel volume for given rpm. Might not be counting all the rpm's, but would not account for fast idle.

Aug 06, 2017 | 1998 Ford Expedition

2 Answers

99 Ford Escort ZX2 2.0L Car will start but won't stay running unless you keep giving it gas


I had the same problem. My car sat for a few days and when i went to start it i heard an extremely loud pop (kind of like a backfire). After that it would start and sound fine, but die 2 seconds later. Thank god my bf is a mechanic he knew instantly that the pcv valve hose that connects to the intake manifold unplugged itself. He plugged it back in and it runs fine now. I didnt however get a check engine light, but i only tried to start it twice before he fixed it because i was scared it jumped time.

Feb 26, 2012 | Cars & Trucks

1 Answer

My car start but shutt off inmedialty


If you have not done so pull the engine codes or have someone do it.
The codes will give you a good idea where to start otherwise the first place I would check is replacing the Crankshaft Position sensor. This is not only very common for them to fail but I have 1994 Laredo and 1996 Laredo and both had the same trouble at exactly the same time. In addition I replaced the Intake Air Temp sensor, coolant temp sensor and idle air control valve on the 1994. The clicking is probably relays and is more than likely normal.

Dec 13, 2011 | 1996 Jeep Grand Cherokee

1 Answer

It won't stay running when put into gear


check for engine vacuum leaks and clean the throttle body and idle speed control air bypass valve, also have the system tested for stored trouble codes, below is how to do that test manually. go to the link.
http://check-engine-light-codes.blogspot.com/2006/03/gm-1983-95-vehicles-obd1-codes-self.html

Aug 08, 2009 | 1989 Pontiac Firebird

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...