Question about Cars & Trucks

1 Answer

EZGO Electric. Motor runs but will not go in forward or reverse.

Can hear motor spinning. Past several times driving there was a "pop" when put in reverse, but it worked fine. Then suddenly would not go reverse or forward?

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

  • Contributor
  • 7 Answers

It sounds like you may have a sheared keyway or pin on the input shaft to the differential. It is highly unlikely that all of the teeth could be stripped from the pinion gear. If you pull the motor loose the problem should be very easy to find.

Posted on May 15, 2017

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

The car has an automatic transmission and all of a sudden i had no reverse had no slipping or nothing the drive gears work fine no slipping grinding nothing shifts through all gears just fine


It may just need servicing/adjusting.

Your reverse gear is actually first gear ... when you select reverse another 'cog' fits into the toothed wheels to change the direction of first gear ... to give you reverse...

It may be a sticky valve or just a bit of adjustment (workshop job..) that is required.

What you can try ..

Start the car ... move the lever through all the positions several times (foot on brake..). Keep your foot on the brake and then put it in reverse and rev the car. Hard!

Try doing it several times.

An auto transmission works on valves opening and closing. Reverse gear - in comparison with the forward gears - is seldom used. The reverse valve can 'stick'. Try forcing it to open ... frighten it ... but keep your foot on the brake...

Jan 18, 2016 | 2001 Chrysler PT Cruiser

2 Answers

Battery is good but when I turn it on it just clicks won't start,maybe after 20 times it starts


Without hearing the sound it makes - it's kind of hard to diagnose.

The engine starting process consists of turning the key to start, the starter motor's rotor moving forward to engage the engine's flywheel, and then the starter motor 's "rotor" spinning until you move the key from "start" to "run". You can hear the starter motor spinning - but one usually can't hear the rotor moving forward to engage the flywheel. As a result, you hear the odd spinning sound - which is the starter rotor spinning. The engine never actually turns over because the rotor never engages the fly wheel. If this is the case, then it is very likely that your starter needs to be checked and / or replaced.

Good luck!

Nov 09, 2011 | 1994 Buick LeSabre

1 Answer

What will cause my car to run rough with little power while in reverse or drive when in park it runs and idles good but it takes a long time to get up speed.


motor mounts and transmission mounts will cause it to be rough while in gear, try power brkaing while in forward and reverse, power braking consists of pressing on the brake while applying gas, if you hear a clunk and hear it you have bad mounts

Sep 03, 2011 | 1992 Chevrolet Cavalier

2 Answers

I have a 1999 chevy malibu and it jumps when i put it in gear but then some times it acts normal for a few days then starts jumping again when i put it in drive some times.


Check the engine mounts with the hood open. Have an assistant observe from the side if any of them are loose when putting the engine in R or D with the parking brake and hydraulic brakes on securely. If the engine mounts are good, they will not allow the motor to twist inside of the engine compartment very much, not more than an inch or two, and good engine mounts will not allow any clunking to occur when putting the car into 'gear.'

Jan 08, 2011 | 1997 Chevrolet Malibu

1 Answer

Power seat will not reverse - electric switch will drive seat forward but reverse setting will not do anything. Are there seperate motors for forward and reverse and is there a way to move the seat...


There are three motors. The one motor moves the seat forward and reverse, one for up and down and one for the tilt. So you may have a problem with the switch. It's possible the switch contacts inside have worn out.

May 15, 2010 | 1998 Dodge Ram 1500 4WD

2 Answers

EZGO golf cart won't go forward


Your batteries have died. The reason it will barely move in reverse is that current is being supplied to the motor is a direction that it spends very little time using. There is a slight change in the armature over time, and reverse tends to work better over time. Check the voltage when under load. (run jumper wires from the + and - of the battery bank. If it is a 36 volt cart and the voltage drops to below 36 volts, you do not have enoug current to run the cart. Plug in the charger and watch the ampmeter. If it goes up to about 20 amps, then it is charging. It should take a good charge after 10 hours. If the cart charges and only runs a short distance, the batteries need replacing.

Apr 09, 2010 | 1993 Acura Vigor

1 Answer

1999 Accord Automatic Transmission issue


im so sorry to say that Honda has a bad transmission line in the 98-02 accord models.. there were severe recalls on this very matter..I only got rid of my 99 accord V6 because the shop who changed my motor mounts crushed my transmission line and blamed it on me..if you had motor mounts or timing done or serpentine belt(i forgot if it has both or just 1),then check to see if transmission line is crushed it can be seen right underneath the battery..

Jun 24, 2009 | 1999 Honda Accord

1 Answer

The 4x4 wheel buttin wont light up, and the 4x4 wont engage


There is a small electric motor on the transfer case that shifts in and out of 4WD. Before you take it off, try resetting the switch. There is a relay in the driver side rear in front of the rear washer fluid reservoir. Hold the white button down for about 10 sec. I am pretty sure it flashes. If that does not work, pull off the electric motor and test it with 12v power. Most of the time they jump past where they are supposed to be. If you reverse the polarity, the motor will turn in reverse.

Jun 13, 2009 | 1991 Ford Explorer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

74945 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...