Question about Cars & Trucks

1 Answer

Finding a glass buld cover - Cars & Trucks

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Cars & Trucks Master
  • 1,830 Answers

What is a glass buld cover? Do you mean bulb?

Posted on May 15, 2017


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I changed headlight bulb but it won't light

1. Never touch the lamp glass with bear hands
2. Visual inspect the connector
3. With a multimeter check the voltage on the connector
3.1 If you have aroubd 12 VDC cabling is ok and you need a new buld
3.2 If not check the cabling connection

Nov 02, 2014 | 2005 BMW 325Ci Convertible

1 Answer

Replace right front turn signal bulb

You may be able to access it from the engine compartment, or from under the car. There's a twist-out buld socket - (twist about an 1/4 quarter turn to the left) - then pull striaght back. If not accessable that way remove the light cover/lens and then the light unit - there should be enough slack in the wires to pull the assembly forward alittle to remove buld socket.

Aug 01, 2014 | 2007 Cadillac DTS Sedan

1 Answer

Replace auto glass

The original oil is best as non genuine will cause problems. Talk to a auto specialist for exact advice.

Apr 26, 2013 | 1995 Lexus Sc 400

1 Answer

Changing the headlights

Try not to touch the buld as you do the installation. There is a access cover in the back of the head lamp. This gives you access to the headlamp. Now when you get to the light buld and socket turn counterclockwise.Then the light bulb wil come out of its socket.From here disconnect the electrical connection.Now for the installation connect the electrical socket to the headlamp bulb.Install the buld in the socket,by rotating socket clockwise locking the retaining tabs to the housing,install cover test the light and you are done2_29_2012_7_31_02_am.gif

Feb 28, 2012 | 2004 Chevrolet TrailBlazer

1 Answer

I have a 2003 Nissan Altima that I have had a new buld put inby the dealer, by myself and By Firestone all in the past 6 months. It is the Left front headlight that this problem occurs. what do I need to...

Most likely, the bulb is not the problem. You probably have a bad connector for the bulb.
AutoZone lists the connectors for your headlamps as follows:

Low beam Connector Part Number 84781
High Beam Connector Part Number 84792

Also, when replacing the bulb, bevery careful to not touch the glass. The tiny amount of oil from your fingerprints can cause "cool spots" on the bulb and cause the glass to crack when the bulb gets hot. If you do accidently touch the glass, Clean it thouroghly with rubbing alcohol and a lint-free,oil-free, piece of cloth. The alcohol wipes from a first aid kit work very well.

Jan 23, 2011 | 2003 Nissan Altima

1 Answer

When i changed the front light buld for the low beam i turn it on and then it smokes and its no more good

if you read the instructions it told you to not touch the bulb or the grease/sweat from your fingers would melt onto and screw up the bulb. try it again and either leave the glass part alone or wear some clean soft gloves.

Dec 10, 2010 | 1997 Honda Accord

1 Answer

Right rear brake light out

Open the back hatch and (if no screws on the outside of light cover) and look for a "door" or door panel that covers the inner side of the lights. Once this is off, find the brake light buld, twist and pull,or just pull out depending on bulb type. Put new bulb in, put door/cover back on, check brake light.

Oct 19, 2010 | 1998 Ford Explorer

1 Answer

Interior overhead light no longer goes on when the door opens or stays on

there should be a little bulb under the cover pop it off and get a new bulb take old buld so parts place can compare

Jan 29, 2010 | 2001 Chevrolet Blazer

1 Answer

Cannot remove front head lamp on car

rotate the buld socket while pulling back on it

Jun 07, 2009 | 2000 Ford Focus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

12 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

79077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

13685 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides