Question about Cars & Trucks

1 Answer

How do I remove my Bennche 700 Bighorns battery I disconnected the terminals but wont lift out what else do I do to remove it

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Habit-Forming:

    Visited the website for 3 consecutive days.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 146 Answers

Check around bottom of battery for bolt that holds batter retention bar in place.

Posted on May 15, 2017

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Removing the starter on a 2008 Saturn Vue XE 2.4L


Starter Motor Replacement (LE5 2.4L and LAT-2.4L)

Removal Procedure

1. Disconnect the battery negative cable. Refer to Battery Negative Cable Disconnection and Connection (With LAT-2.4L) ( See: Vehicle Lifting > Procedures > Lifting and Jacking the Vehicle) .

Zoom and Print Options
3. Disconnect the starter motor electrical connector (3).
4. Remove the starter solenoid BAT terminal nut (4).
5. Remove the battery positive cable terminal (1) and engine harness terminal (2) from the starter motor.

Zoom and Print Options
6. Remove the starter motor bolts.
7. Remove the starter motor from the vehicle.



Installation Procedure

1. Position the starter motor to the vehicle.

Zoom and Print Options

Notice: Refer to Fastener Notice ( See: Vehicle > Vehicle Damage Warnings > Fastener Notice) .


Important: Hand tighten all bolts before finalizing any torques.


2. Install the starter motor bolts.

Tighten the bolts to 43 N.m (32 lb ft).


Zoom and Print Options
3. Install the engine harness terminal (2) and the battery positive cable terminal (1) to the starter motor. Ensure that the battery positive cable terminal anti-rotation feature is aligned correctly.
4. Install the starter solenoid BAT terminal nut (4).

Tighten the nut to 15 N.m (11 lb ft).

5. Connect the starter motor electrical connector (3).

image-5snr4wklzrtsarf5gbfkw1ee-3-0.gif

image-5snr4wklzrtsarf5gbfkw1ee-3-2.gif

image-5snr4wklzrtsarf5gbfkw1ee-3-5.gif

Jul 08, 2017 | Saturn Cars & Trucks

1 Answer

Replace starter


Starter Replacement
Removal Procedure
Caution: Before servicing any electrical component, the ignition and start switch must be in the OFF or LOCK position and all electrical loads must be OFF, unless instructed otherwise in these procedures. If a tool or equipment could easily come in contact with a live exposed electrical terminal, also disconnect the negative battery cable. Failure to follow these precautions may cause personal injury and/or damage to the vehicle or its components.
  1. Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection .
  2. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information.
    alt="Object Number: 217186 Size: SH">
  3. alt="Click here for detailed picture of above image.">
  4. Remove the positive battery cable starter motor lead nut (1) from the starter.
  5. Remove the positive battery cable lead from the starter.
  6. Remove the starter solenoid terminal lead nut (2) from the starter.
  7. Remove the starter solenoid terminal lead from the starter.
    alt="Object Number: 217190 Size: SH">
  8. alt="Click here for detailed picture of above image.">
  9. Remove the starter motor bolts (2, 3).
  10. Remove the starter motor (1).

Sep 23, 2015 | 2000 Cadillac Catera

1 Answer

Where is the starter located on a 2008 pontiac g 6 4 cylinder


Disconnect the negative battery cable. Refer to Battery Negative Cable Disconnection and Connection. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle. Remove the "S" terminal connector from the starter solenoid. Remove the engine harness lead (2) from the starter
Remove the positive battery cable nut (2) from the starter solenoid. Remove the positive battery cable (3) and engine harness terminal (4) from the starter solenoid.
Remove the starter motor bolts. Remove the starter motor.
Has four engines possible in your G6 ,starter removal is simalier for all except one the catalytic converter has to come off.

Mar 30, 2015 | 2008 Pontiac G6

1 Answer

How do i change battery in 2006 seabring


REMOVAL The battery is accessible without removing the left front wheel and tire assembly..
1. Verify that the ignition switch and all accessories are OFF. 2. Turn the steering wheel to the full left position. 3. Disconnect and isolate the negative battery cable remote terminal from the remote battery post. WARNING: NEVER GET UNDER A LIFTED VEHICLE IF NOT SUPPORTED PROPERLY ON SAFETY STANDS.
4. Remove battery splash shield. Refer to the Body section of the service manual for the procedure. 5. Disconnect the heater blanket cord, if equipped.
316275.jpg Fig. 1 - Battery Location 1 - BATTERY HOLD DOWN 2 - BATTERY
6. Remove the short bolt from the battery hold down and remove the hold down Fig. 1 . 7. Disconnect the negative and positive battery cables from the battery. 8. Slide the battery toward rear of vehicle and lift out of the battery tray. 9. Remove battery from vehicle.

Jan 21, 2011 | 2006 Chrysler Sebring

1 Answer

1999 toyota avalon, starter location, or engine view diagram


it's under the battery. see instructions below for removing.

REMOVAL & INSTALLATION

  1. Disconnect the cable from the negative terminal of the battery.
  1. On some early models with cruise control, you may have to remove the battery.

    Also on some models with cruise control, remove the actuator cover and disconnect the wiring harness. Remove the three bolts and then lift out the cruise control actuator. Remove the bracket from beneath the actuator and put aside.
  1. Peel the rubber boot away and remove the nut and disconnect the negative battery cable from the magnetic switch terminal on the starter. Disconnect the electrical connector also located on the magnetic switch.

1f54e61.gif Fig. Remove the these two starter mounting bolts . . .
  1. Support the starter by hand and remove the two mounting bolts.
  1. Remove the starter from the transaxle.

Oct 04, 2010 | Toyota Avalon Cars & Trucks

1 Answer

How do I replace the battery on my 2004 pt cruiser?


Steps to replace the battery

Air Cleaner Removal

1. Loosen the air intake hose clamp (with a flathead screwdriver), which holds the intake tube to the air box lid.

2. Once the hose clamp is loosened, pop open the two spring-loaded clamps on the left and front side of the air box. The clamps help secure the lid to the air box. On the back of the air box lid there are 4 plastic slots, which match up with 4 corresponding tabs on the air box. In order to unhinge the lid from the air box, slide the lid away from you about an inch and gently lift the lid up. Ensure that the lid is free from the air box hinge; then carefully disconnect the air intake hose from the lid at the hose clamp and remove the lid from the engine compartment.

3. Lift the air filter out of the air box. 4. Disconnect the PCV hose from the lower air box.

5. The lower air box is removed by just tugging straight up on it. It will pop out as it's held in place by two rubber pins that wedge into the indentations in the plastic air box.

Battery Removal

6. Disconnect the battery terminals - negative 1st, the positive. 7. Remove the anchor bolt at the base of the battery using a 1/2" socket. 8. Lift battery out (with a battery carrier strap). Save the thermal blanket wrap to slip on the new battery.

Cleanup and Installation

9. Clean the terminals by dipping in a cup filled with baking soda and warm water. Use a battery terminal cleaning tool, wire brush to remove the corrosion or a tiny screw driver to scrape with. Rinse with water and clean up the tray with a towel.

10. Install the thermal blanket on new battery. Note the position of the notches on the blanket when replacing it. Lift into car and slide the battery as much as possible towards fender. Reinstall retaining bolt.

11. Install felt washers ($1) to prevent corrosion on the terminals

12. Reinstall terminals (positive 1st, then negative). Apply some grease or Vaseline to the tops of the terminals.

13. Reinstall air cleaner box. Carefully line it up and push down Make sure to seat it completely when you reinstall it.

14. Reinstall filter; cover. Make sure clips are on tight.

Thank you for using fixya and good luck
http://www.ptcruiserlinks.com/forum/pt-cruiser-videos/19853-video-how-replace-battery.html

Aug 05, 2010 | 2004 Chrysler PT Cruiser

1 Answer

How to remove battery from 1999 cadillace sedan deville


Disconnect negative terminal (black) first. Then disconnect positive terminal (red).

Then, use a 1/2" hex socket and extension and ratchet to unscrew the hold down bolt that holds the black plastic hold down piece on the bottom of the battery.

Remove any cross members that block the lifting of the battery out of the battery tray, by unscrewing any bolts that are located on the plate.

May 21, 2010 | 1999 Cadillac DeVille

1 Answer

Need to replace battery, how do you remove the air box


Steps to replace the battery

Air Cleaner Removal

1. Loosen the air intake hose clamp (with a flathead screwdriver), which holds the intake tube to the air box lid.

2. Once the hose clamp is loosened, pop open the two spring-loaded clamps on the left and front side of the air box. The clamps help secure the lid to the air box. On the back of the air box lid there are 4 plastic slots, which match up with 4 corresponding tabs on the air box. In order to unhinge the lid from the air box, slide the lid away from you about an inch and gently lift the lid up. Ensure that the lid is free from the air box hinge; then carefully disconnect the air intake hose from the lid at the hose clamp and remove the lid from the engine compartment.

3. Lift the air filter out of the air box. 4. Disconnect the PCV hose from the lower air box.

5. The lower air box is removed by just tugging straight up on it. It will pop out as it's held in place by two rubber pins that wedge into the indentations in the plastic air box.

Battery Removal

6. Disconnect the battery terminals - negative 1st, the positive. 7. Remove the anchor bolt at the base of the battery using a 1/2" socket. 8. Lift battery out (with a battery carrier strap). Save the thermal blanket wrap to slip on the new battery.

Cleanup and Installation

9. Clean the terminals by dipping in a cup filled with baking soda and warm water. Use a battery terminal cleaning tool, wire brush to remove the corrosion or a tiny screw driver to scrape with. Rinse with water and clean up the tray with a towel.

10. Install the thermal blanket on new battery. Note the position of the notches on the blanket when replacing it. Lift into car and slide the battery as much as possible towards fender. Reinstall retaining bolt.

11. Install felt washers ($1) to prevent corrosion on the terminals

12. Reinstall terminals (positive 1st, then negative). Apply some grease or Vaseline to the tops of the terminals.

13. Reinstall air cleaner box. Carefully line it up and push down Make sure to seat it completely when you reinstall it.

14. Reinstall filter; cover. Make sure clips are on tight.

Good luck and thank you for using Fixya

Mar 07, 2010 | 2005 Chrysler PT Cruiser

1 Answer

2005 DODGE STRATUS HOW TO REPLACE THE BATTERY


REMOVAL
The battery is accessible without removing the left front wheel and tire assembly..

Verify that the ignition switch and all accessories are OFF.
Turn the steering wheel to the full left position.
Disconnect and isolate the negative battery cable remote terminal from the remote battery post.
WARNING: NEVER GET UNDER A LIFTED VEHICLE IF NOT SUPPORTED PROPERLY ON SAFETY STANDS.

Remove battery splash shield. Refer to the Body section of the service manual for the procedure.
Disconnect the heater blanket cord, if equipped.
Remove the short bolt from the battery hold down and remove the hold down (Battery Location).
Disconnect the negative and positive battery cables from the battery.
Slide the battery toward rear of vehicle and lift out of the battery tray.
Remove battery from vehicle.

Oct 18, 2009 | 2005 Dodge Stratus

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

26 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...