Question about Cars & Trucks

1 Answer

2001 s10 brakeline diameter - Cars & Trucks

Posted by on


1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points


    An expert that got 5 achievements.


    An expert who has written 20 answers of more than 400 characters.


    An expert who has answered 20 questions.

  • Expert
  • 73 Answers

I believe the distributed brake lines are all 3/16".

Posted on May 15, 2017


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How often should you bleed the brakes for a 2006 ford freestar?

You only need to bleed the brakes when you crack the system to put on a new caliper or pads or shoes or slave cylinder or brakeline or flex hose etc.

Nov 27, 2013 | 2001 Ford Taurus

1 Answer

Put new calipers on the front along with new brakes. right brakeline getting no break fluid to the caliper.. wat could be the issue?

If you have bled the new calipers and still get no fluid out of them, I would look at the master cylinder or a blockage in that particular brake line.

Oct 29, 2013 | 2001 Ford Focus

1 Answer

Leaking back break lines

This is a serious problem. Depending on what material you use, and who works on this car, will directly reflect on the price of the repair.

Many of the replacement parts have to be hand fitted. Some preformed lines are available, but they are often sold as a complete set.

There are special tools needed to create a brakeline out of a coil of material. Each end of brakeline would need to be crimped with the correct fitting for the individual inlet hole. Using different sizes of fitting is the Manufactuers method to insure that the brakeline fits in only the correct place.

This made more sense when replacements were bolt on parts and readily available. Today though, it is a complication to buy different size ends for each brakeline.

You are going to want to go either to a Brakeshop or someone who has done this work before. Consider this, all Brakelines were installed the same day on the Assembly line. If 2 leak now, it won't be long before all 4 leak. If you do not know the History of the car, and what was replaced earlier, you need someone to inspect the brakes.

Oct 07, 2012 | Chevrolet Cars & Trucks

2 Answers

2001 Chevy s10 4.3 surges and won't pick up speed. Valves rattle when you mash accelerator to the floor and it smells like its flooding out

You want to start with the knock sensor, located on the side of the block, about 1 1/4 inches in diameter, 1 1/2 inches long. funny looking sensor. It is suposed to pick up knocks/pings in the engine and tells the ECM to advance or ****** the engine. Check the engine for codes, even if the light is not on. Let me know we can go from there

Feb 24, 2011 | 2001 Chevrolet S-10

1 Answer

How do i remove a starter from a 1994 s10 pick up with a 4.3 v6

Disconnect negative battery cable. Raise and suppor
t vehicle. Disconnect electrical wiring from starte
solenoid. Remove mounting bracket and wiring from b
rush end of starter. Remove skid plate (if equipped
Remove 2 brakeline-to-crossmember brackets.
Remove 6 crossmember bolts and remove crossmember.
Remove transmission cooler line-to-flywheel
housing bracket. Remove brace rod to flywheel housi
ng. Remove lower flywheel housing cover (if necessa
Remove starter bolts. Note location and number of s
hims for reassembly. Remove starter. To install, re
removal procedure.

Jun 22, 2010 | 1994 Chevrolet S-10

1 Answer

Hi i want to know does 2001 s10 ecm harness can

It does not fit since the connectors are not similar.

Sep 25, 2009 | 2001 Chevrolet S-10

2 Answers

Broke a brakeline on my 1996 taurus how do i fix or cap it so i can use the car 4 wheel disc sys

It has to be replaced. If its front new break hose that runs from hard line to caliper. If rear from caliper to block on rear axel. If main line from front of car at perporationing valve back to block on rear axel.

Apr 13, 2009 | 1996 Ford Taurus

1 Answer


It is possible to replace a bad portion of brake line using compression fittings,and alot of parts stores do fabricate and sell brakeline if you take the old piece(s) in for a reference.If you do pull the line from the resevoir your going to have to bleed the entire system incuding the master cylinder,If you have the means I would reccomend taking it to a shop that specializes in brakes,they have the tools and experience to do the job correctly and it really shouldn't be to expensive.If you are going to DIY write me back and I'll give you a walk through on the procedure.

Apr 10, 2009 | 2001 Kia Sportage

1 Answer


hi i have had the brakeline fixed.i sent it in to the shop.they droped the tank was better they did it anyway as you have to have a
licence to work on brakelines.

thank you for bing there it's cool

Sep 07, 2008 | 1990 Toyota 4Runner

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides