Question about Cars & Trucks

Open Question

Which is good in chinese steel pipe?

I want to buy some steel pipe in china,but I do not know.

Posted by on


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

Removing crank pulley bolt on Honda 2.3L

I learned a trick that might help. Well two. First is using torch and heat the pulley just around the bolt for a few seconds. This shocks the metal and with a good impact gun should get it off. Now the other. Not recommended but if nothing else works it may work. So need to turn the key and find out if the engine crank turns clockwise rotation if yes then this may work. Using a large breaker bar and 4 foot pipe slide to pipe over the breaker bar with that on the pulley bolt. So now the dangerous part. Turn the engine with key and my suggestions is have the pipe resting on the frame or ground and not use it if it's going to hit anything that is important like hoses or radiator it will get smashed when you crank the key to turn the stater. It will either spin or not. Or break tools so this is not recommend way to get it lose. 4 foot pipe is long enough so you can handle it and don't use light pipe. Use steel thick wall. I use 1 1/2 inch steel pipe can get at even homedepot or scrap pile if you know a guy.

Feb 11, 2018 | Honda Cars & Trucks

2 Answers

Can I make a better head gasket for 80cc china bicycle motor ?

head gasket materials include copper sheet. exhaust manifold material ( pink ) or none at all except loctite red spread sparsely over the head face
any material used has to be thin (.020" ) as the thicker it is the better chance it will burn out
you may be able to research head gaskets because most engine have a similar design and for example a china made B&S may do the job or a different china made engine may have a gasket that will adapt
check the method of fitting the OEM gasket
check that the head is flat ( may need machining)
do not reuse old head studs ( they stretch and loose tension )
clean out stud holes as they can bottom out on muck and oil and not get the right tension
use a sealant adhesive on the OEM gasket to stick the head back on to resist movement from compression frequency

Mar 12, 2017 | Cars & Trucks

1 Answer

What Reasons Limiting Casting Mold to Develop in China?

First, although importance of casting mold foundry is recognized by more and more people, recognition has not reached to due height yet. So, status of mold is still not clear and policies cannot be implemented completely. Received supporting strength and intensity are insufficient. Besides insiders, only a few people know about features of mold industry. To get more supports, publicity is still priority. Second, compared with international advanced level, Chinese casting mold industry is still backward on idea, design, craft, technology and experience. In general, China is still learning from advanced countries, lacking of innovation. Information manufacturing and management, innovation are not realized. China is equivalent to intermediate level. Compared with advanced level, the whole industry level is backward by about 15 years. Among that, online test and information management of casting mold are backward by more than 15 years. Reducing gap has a long way to go forward.Third, the high economic growth rate is almost ended. In the future, Chinese economy will show the trend of intermediate speed. Cost inflation and rate of profit declining will become normal and constraining force of energy and ecological environment will be larger and larger. Structural adjustment and transformation of growth pattern are urgent. There are a lot of factors around the world. Under such situation, castings mold industry has difficulty for maintaining higher growth rate and sustainable development while the objective must be realized.Forth, phenomena of financing difficulty, accounts due growing, financial strain, cost growing and rate of profit constantly decreasing still exist in small enterprises and those problems are not figured out, still growing continuously. Partial provinces or cities in south have energy supply tension. Situation that commercial power is limited also exists. Fifth, talent is in shortage. In particular, shortage of senior talent has become a key bottle neck for mold industry. Although China has made a great progress in talent cultivation, it is still far away from meeting requirements. Demographic dividend in China is continuously reducing and human resource will be tightened for a long time. Enhancing talent cultivation to meet demand, using high technologies, developing informatization, standardization and automation to reduce manpower are priorities.

Jan 05, 2017 | Cars & Trucks

2 Answers

Is it true the energy bulbs made in china can burst and cause a fire

I have had some Chinese LED bulbs fail very soon after fitting but no flames so far.

Dec 29, 2014 | Cars & Trucks

1 Answer

We are bearing factory from China,We supply all kinds of needle roller bearing Cam followers, Yoke Type Track Rollers,needle roller, auto bearings,with high quality and competitive price ! peugeot...

no thanks only buy swedish or german bearings a they last forever ,compared to chinese stuff like the bearing in a swimming pool pump i bought from china ,less than a week and its noisy ,last pump lasted 22 years

Aug 25, 2011 | Peugeot 405 Cars & Trucks

1 Answer

Lug nuts are off but tire won't budge

put a couple of lug nuts back on about three turns or so and with the vehicle supported on a good sturdy jack, give the tire a really good shot with a baseball bat, steel pipe etc.on the inside (hit the tire, not the wheel, unless it's a steel not aluminum one) WD40 or other solvent sprayed in through the stud holes often helps when doing this. Sounds crude but just about every shop has a steel pipe etc for exactly that use.
Don't try this using a standard bumper jack or the car can fall on you!
Clean around the hub before replacing the wheel as that is where they generally get stuck.

May 14, 2010 | 2007 Jeep Liberty Sport

1 Answer


Spray some wd 40 into the wheel holes where the studs come through. Then(this will sound crude but it's real) with the vehicle supported firmly on a good jack (floor jack preferred) Take a steel pipe or solid baseball bat and give the inside of the tire a really hard shot. Nearly every shop I know has a steel pipe about four feet long set aside for this very purpose!

Oct 17, 2009 | 2005 Ford Explorer Sport Trac

1 Answer

Abs brakes feel likes they are pulsing just before 2006 EQUINOX comes to full stop. Just changed rotors and pads. Rechecked, everything seems "tight". Can Abs sensors be disconnected one at a time (or all)...

Sounds like warped rotors. Where did you buy them? The "cheap-o" replacements are made in China and if not stored properly, will be warped when you buy them ! ! ! I'd take them back and have the Auto Store check them and/or give you a replacement. If they hand over another pair, ask them to check them BEFORE you take them home... I've had this same problem at O'Reilly's in the past but other stores handle the same Chinese replacments...

Oct 13, 2009 | 2006 Chevrolet Equinox

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

25 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

77932 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14403 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides