Question about Cars & Trucks

Open Question

1998 NPR 4 cyl diesel torque specs on cyl head?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 25 Answers

SOURCE: 87 samurai bolt torque specs for engine

The haynes book is not recommended since there are numerous mistakes and they still will not update. One of the biggest is the firing order.

The factory service manual is the only way to go.

Head bolts - 46 - 50.5 lbs (there is an order sequence for the bolts)

Intake & exhuast manifolds- 13.5 - 20 lbs

Flywheel - 41.5 - 47 lbs

Clutch cover - 13.5 - 20 lbs

Posted on Mar 17, 2009

  • 701 Answers

SOURCE: torque specs for toyota tercel

Hello vienotkelly: The correct Main bolt torque is 42 foot pounds. The connecting rods torque to 29 foot pounds. The torque sequence for the head bolts and the correct way to tighten the bolts are attached to this reply. Thak You for using6bd0ae1.jpg FixYa. Roger

Posted on Apr 15, 2009

Danno5691
  • 17 Answers

SOURCE: I need the torque specs and sequence on a 1998 chevy 350 vortec

Vortecs are a little different that old school small blocks, grab a Haynes or Chiltons, the cross patterns and specs are simply diagramed. Vortec, as any really, start with 25# then 45# and then final torque which I believe is around 70-75# but to be sure verify with the manual. AutoZones, Murry's, Adavance auto all carry the books, Cheap insurance.
Dan

Posted on Apr 25, 2009

polarcycle
  • 1392 Answers

SOURCE: head bolt torque spec

Always use new head bolts.
1)tighten to 40ft/lbs
2)back off 1/2 turn
3)tighten back to 40ft/lbs
4)tighten an additional 90 degrees
5)tighten an additional 90 degrees.

Posted on Aug 16, 2009

inspectmycar
  • 233 Answers

SOURCE: 94 mazda B3000 3.0L cylinder head torque specs

Step 1 torque to 59 ft pounds
2. Loosen one full turn
3. 37 ft pounds
4. 68 ft pounds

Use torque sequence below
aca9f77.gif

Posted on Sep 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How much torque for each head bolt in a 2004 Dodge ram 1500 3.7 liter


Install the cylinder heads. Use new gaskets and tighten the bolts, in sequence, as follows:
  1. Step 1: Bolts 1-8 to 20 ft. lbs. (27 Nm)
  2. Step 2: Bolts 1-10 verify torque without loosening
  3. Step 3: Bolts 9-12 to 10 ft. lbs. (14 Nm)
  4. Step 4: Bolts 1-8 plus 1 / 4 (90 degree) turn
  5. Step 5: Bolts 9-12 to 19 ft. lbs. (26 Nm)


26002143-2qxw3km0vcnqu3setvnduoab-2-1.gif

Dec 10, 2015 | Dodge Cars & Trucks

1 Answer

Cyl head torque specs


go google --type in torque specifications for toyota ( your vehicle ) diesel. There are pages that will give the specs and the rotation to do the job.

Jun 27, 2014 | 2005 Toyota LandCruiser Prado

1 Answer

I need the tork spec on 1998 Buick 3800 block for the cylinder head.


hope this helps,

Torque sequence --------- front ' 6 1 3 7 ' of ' ' engine ' 8 4 2 5 ' --------- Step 1: torque bolts in sequence to 37 Ft/Lbs Step 2: torque all bolts in sequence an additional 120 degrees Step 3: torque bolts 1,2,3, & 4 an additional 30 degrees recheck final torque in sequence *** CAUTION ***engine uses Torque To Yield head bolts (TTY) thatpermanently stretch during the initial installation.New head bolts must be used when cylinder head isreplaced or re-installed to obtain proper torque.
always torque from center
Tighten each bolt an additional 90° in sequence.


0996b43f8021ae77.jpg

Jun 18, 2011 | 1998 Buick LeSabre

1 Answer

I AM DOING THE HEAD GASKET ON 1999 SAAB 95 4 CYL I NEED THE TORQUE SPEC ON CYL. HEAD


Torque spec

Step 1- 44 Ft.Lbs.
Step 2- 59 Ft.Lbs.
Step 3- Tighten bolts an additional 90 degrees.

Here the head bolt's tightening sequence.

bcas1298_1.gif

Nov 11, 2010 | Saab 9 5 Cars & Trucks

2 Answers

Need torque specs for 2000 chevy malibu 3.1 cyl heads & intake


(step 1 ) the torque specs for the heads are---1998 through 2001 are 37 foot lbs. ( step 2) rotate an additional 90-degrees (1/4 turn). intake manifold bolts ( lower ) step 1-- 62 in-lbs, step 2--115 in-lbs. intake manifold bolts/studs ( upper ) 18 ft-lbs. this is for the 3.1 v-6, have a good day!

Aug 14, 2010 | 2000 Chevrolet Malibu

1 Answer

I need to know what the cyl head torque and rocker arm torque is for a 1998 6.5 L GM turbo diesel.


Cylinder head bolts are done in 3 steps. Step 1 - 20 ft.-lbs
Step 2 - 50 ft.-lbs
Step 3: Tighten an additional
90 degrees.
Lifter guide plate bolts 18 ft-lbs
Rocker arm shaft bolts 40 ft-lbs
Hope this helps.

Aug 06, 2010 | 1999 GMC Sierra 3500

1 Answer

What are the torque specs to tighten a cylinder head for a 1998 ford f150 4.2 6 cyl


Step 1 14 ft.lbs
Step 2 29 ft.lbs
Step 3 36 ft.lbs
Step 4 loosen 3 revolution and torque in sequence, one bolt at a time, and torque to next step.
Step 5 short bolts 15-32 ft.lbs
long bolts 30-36 ft.lbs
Step 6 additional 175-185 degrees.

d6dadf6.gif

Jul 07, 2010 | Cars & Trucks

3 Answers

Need to know the head bolts torch specs on 98 toyota v6


heres the torque specs and the way to tighten the head bolts for your 1998 toyota sienna, hope this helps,
12 point bolts step 1- 40 ft lbs
step 2- additional 90 degrees
recessed bolt 13 ftlbsaf151d2.gif

May 12, 2010 | 1998 Toyota Sienna

2 Answers

Head bolt torque spec


Always use new head bolts.
1)tighten to 40ft/lbs
2)back off 1/2 turn
3)tighten back to 40ft/lbs
4)tighten an additional 90 degrees
5)tighten an additional 90 degrees.

Aug 16, 2009 | 1999 Ford Escort

4 Answers

Head bolts torque settings


According to my haynes manual for G-S reg, 1989-1998 it goes as follows,
Stage 1:- Tighten all bolts by hand until bolt heads just contact cyl. head.
Stage 2:-Tighten all bolts to 40Nm or 30lb ft.
Stage 3:-Angle tighten all bolts a further 60 degrees.
Stage 4:-Angle tighten all bolts again a further 60 degrees.
Stage 5:- M12 x 140mm bolts ONLY angle tighten a further 20 degrees.
Hope this helps everyone, sorry it seems longwinded but that is how it's written in the manual.

Oct 26, 2008 | 1995 Land Rover Discovery

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

24 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...