Question about Cars & Trucks

Open Question

How I can remove the motor windshield. all compartment it's sealed and is no way to get off the arms.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 76691 Answers

SOURCE: Windshield Wiper Arm

Pull up on the wiper arm, you will see a tiny little blade on the side of the wiper arm where it goes over the post, take a little screwdriver and pry that out board, this will release the arm from the post, it will be tight, wiggle the arm and pull straight out away from the post.

Posted on Oct 19, 2008

Ad
  • 8 Answers

SOURCE: windshield wipers

According to AllData, you don't have to remove the motor to install a new switch. Subsequently, AllData doesn't give direction on wiper arm or motor removal. Here are the only diagrams they give for switch replacement.

41917584 41917585

Posted on Nov 26, 2008

morganismo
  • 36 Answers

SOURCE: windshield wiper arm

These are a tight fit...Spray a little penetrating lubricant onto it and let it sit for about 20 minutes. You will notice there are splines that match up from the drive unit to the base of the wiper arm...sometimes these can get a little corroded and becasue of the relative surface area it makes them a real pain to get off. You may need to just pry against it gently with a flat head scredriver after you spray on the lubricant. Pray at it from all different sides of the base so that it doesn't bind up and get crooked.

Hope this helps! Good Luck!

Posted on Feb 12, 2009

  • 1 Answer

SOURCE: Windshield wiper arm disconnected

My dad helped me solve this problem on my truck...

They simply pry off. He put down a towel to protect the cowl grill, took a hammer (using the split end) and pried them right off.

There was no mechanism holding them on, when we were done working under the grill, we used the same towel, but the other side of the hammer to stick 'em back on.

Posted on Mar 30, 2009

  • 43 Answers

SOURCE: Windshield wipers will not move. Arms from motor

Hello

The windshield wiper linkage comes as an assembly. The assembly comes with the two rotating splines that the wiper arms attach to. you must remove wiper arms. Remove cowl trim and remove bolts that hold the pivot points to the body. The new linkage that snaps to the wiper motor should come with a new retaining clip. You have to fish the linkage assembly through the access holes in the body by un bolting the wiper motor.

Posted on Dec 19, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do you replace windshield wiper motor on a 1997 ford e250 van


REMOVAL
  1. Raise and support the hood.
  2. Remove the windshield wiper pivot arms.
  3. Remove the cowl top vent panels.

25287270-15uk5heqgoha5mc4ejw3dmql-1-0.gif
  1. Disconnect the windshield wiper mounting arm and pivot shaft.
  1. Remove the access cover from the dash panel.
  2. Remove the mounting arm and pivot shaft retaining clip.
  3. Disconnect the windshield wiper mounting arm and pivot shaft from the windshield wiper motor.

25287270-15uk5heqgoha5mc4ejw3dmql-1-2.gif
  1. Remove the windshield wiper motor.
  1. Disconnect the electrical connector.
  2. Remove the three bolts.
  3. Remove the windshield wiper motor.
INSTALLATION

25287270-15uk5heqgoha5mc4ejw3dmql-1-5.gif
  1. Install the mounting arm and pivot shaft retaining clip on the windshield wiper mounting arm and pivot shaft.

25287270-15uk5heqgoha5mc4ejw3dmql-1-9.gif
  1. Install the windshield wiper motor.
  1. Place the windshield wiper motor in the dash panel.
  2. Install the three retaining bolts.
  3. Reconnect the electrical connector.

25287270-15uk5heqgoha5mc4ejw3dmql-1-14.gif
  1. Reconnect the windshield wiper mounting arm and pivot shaft.
  1. Press on the windshield wiper mounting arm and pivot shaft after it is aligned with the windshield wiper motor.
  2. Install the access cover in the dash panel.
  1. Install the cowl top vent panels.
  2. Install the windshield wiper pivot arms.
  3. Adjust the windshield wiper pivot arms.
This is technically for the V6 4.2L but I'm sure those Ford E250's have the same setup for windshield wiper motor. Let me know how it goes.

Nov 17, 2014 | Cars & Trucks

1 Answer

How to replace a front windshield wiper motor?


You need to pop your hood up, remove your windshield wiper arms but make sure you mark the position of the arms marking on the arm and arm attachment for re-installation alignment, Remove rubber seal and plastic screws (Phillips head), remove windshield wiper water line from left side, then carefully remove plastic cowl. Under neath will be your wiper arms and motor. You can remove all 8 mm bolts and then remove whole plastic cowl and deatach the wiper motor. Installation is in reverse order of removal.

Oct 14, 2013 | 2002 Ford Windstar Cargo

1 Answer

How to replace the wiper motor on a 1994 volkswagon golf


The wiper motor on a Volkswagen is an electric motor connected through a drive linkage to the wiper arms. Windshield wipers are an integral feature for operating a motor vehicle safely. If your wipers are not functioning, or seem to lack the speed or power they used to have, the wiper motor should be removed and replaced immediately
.


Location
  • The wiper motor on a Volkswagen is located directly underneath the plastic cowl cover. The cowl cover is located directly below the windshield.

Removal
  • Begin by removing the wiper arms by prying off the covers at the base of the arms and removing the nuts that secure the arms to the drive shafts. Label the passenger and driver arms so they can be installed in the same positions. They are not interchangeable. Remove the rubber hood to cowl weather seal. Unscrew the plastic fasteners from the driver's side of the cowl cover, then remove this half of the cover. Remove the fasteners from the passenger's side cowl cover and remove this half of the cover. Disconnect the windshield wiper motor wiring harness by separating the plastic wiring connector. Remove the three bolts that secure the wiper motor to the vehicle's body. Pull the motor slightly away from the body, then remove the nut that connects the motor shaft to wiper linkage. Remove the motor.

Installation
  • Place the new wiper motor into position in the cowl and reconnect it to the wiper arm linkage. Then reinstall the three retaining bolts. Reconnect the plastic wiring connector to the wiper motor wiring harness. Place the cowl covers into position below the windshield and reinstall the plastic fasteners that retain them. Reinstall the rubber hood to the cowl weather seal. Reinstall the wiper arms in the same position you removed them from, along with the wiper arm retaining nuts and lower wiper arm covers. Turn the windshield wipers on and test for proper operation. If the wiper blades slap against the bodywork surrounding the windshield, loosen the nuts that connect the wiper arms to the shafts and adjust.

More Read: OBD2 car diagnostic tool

Aug 06, 2012 | 1994 Volkswagen Golf

1 Answer

How to replace wiper motor on a 1994 Ford F-150


  • Locate the wiper motor, and disconnect the electrical wires from it by unplugging them. The wiper motor is in the engine compartment against the back firewall near the driver's side.
    Disconnect the wiper arms from the wiper motor linkage by using the pliers to remove the clip.
    Locate the wiper motor in the engine compartment on the back firewall and remove it with the proper size wrench. There are three attaching bolts.
    Remove the wiper motor by twisting it around if you have to. The wiper arm linkage will come out with it. good-day !





  • 3Remove the cowl grill under the windshield wipers using the proper size screwdriver. This is the grill that you see under the wiper arms before the engine compartment hood starts.


  • Read more: How Do I Remove a Windshield Wiper Motor from a 1994 Ford F-250? ' eHow.com http://www.ehow.com/how_7195498_do-motor-1994-ford-f_250_.html#ixzz1odr1irhn

    Mar 09, 2012 | 1994 Ford F150 Styleside Supercab

    1 Answer

    Where is the location of acura tl 2004 wiper motor?


    The wiper motor is located in the left rear of the engine compartment near the corner by the driver side. Remove the wiper arm assembly (both if necessary) and then remove the plastic cover at the edge of the hood near the windshield the motor is underneath. To remove the wiper arm flip up the small cover where the arm is attached and you will find a (12mm usually) nut. Remove the nut and work the arm off of the post using a rocking motion. Hope this helps.

    Sep 02, 2011 | 2004 Acura TL

    1 Answer

    Where is the wiper motor on my 1999 GMC Yukon?


    Windshield Wiper Motor
    Removal & Installation
    To Remove:


    1. Remove wiper arms.
    2. Remove weatherstrip from cowl.
    3. Remove two cowl vent grille panel screws.
    4. Remove windshield nozzles and hoses.
    5. Remove three cowl vent grille panels.
    6. Disconnect windshield wiper motor electrical connector.
      NOTE: Do not remove crank arm from windshield wiper motor.

    7. Loosen nuts that attach the drive link brackets to the crank arm.
    8. Remove wiper motor crank arm brackets.






      gm-06-00-1079.gif



    9. Remove three bolts and windshield wiper motor from vehicle.

    To Install:


    1. Install windshield wiper motor and three bolts.

      • Torque to: 62 in lbs. (7 Nm)

    2. With right side linkage closest to the windshield wiper motor, install drive
      link brackets to wiper motor crank arm.

      • Torque nuts to: 44 in lbs. (5 Nm)

    3. Connect electrical connector.
    4. Install nozzles and windshield washer hoses to cowl vent grille.
    5. Install three cowl vent grille panels and screws to vehicle.
    6. Install weatherstrip to cowl.
    7. Install wiper arms.


    prev.gif next.gif

    Oct 30, 2010 | 1999 GMC Yukon

    1 Answer

    The wiper motor on my 1983 Ford Ranger still works but the wipers no longer move. I think there is a failure of the mechanical linkage. Where do I go to find repair parts?


    why do you think the motor still works if the wipers don't move? Can you hear the motor run or can you see a little movement when you turn the switch on?

    What happens when you activate the washers?

    go to a salvage yard that allows you to remove the parts yourself. Then you can see how the motor and linkage assembly comes out.


    don't have 1983 info, but here is 1994:

    Section 01-16A: Wiper and Washer System, Ranger/Explorer 1994 Ranger and Explorer Vehicles Workshop Manual
    DESCRIPTION AND OPERATION Windshield Wiper System, Ranger/Explorer The windshield wipers are actuated by a permanent magnet, rotary-type electric windshield wiper motor (17504) . The two windshield wiper pivot arms (17526) and windshield wiper blades (17528) are mounted on a pivot shaft, one at each side of the windshield. The windshield wiper mounting arm and pivot shaft (17566) are connected to the motor by windshield wiper adapter and connecting arm clip (17531) . Ranger and Explorer vehicles are equipped with an interval wiper and washer (IWW) system featuring a lever-type turn signal and windshield wiper switch (13K359) mounted on the steering column. The IWW windshield wiper governor (17C476) uses a relay contact to control current to the windshield wiper motor . The governor electronic circuitry controls the contact to supply current to windshield wiper motor . A rear wiper/washer system is available on Explorer vehicles. The rear window wiper system consists of a windshield wiper motor mounted inside the liftgate (40010) , an articulating windshield wiper pivot arm and windshield wiper blade , a windshield wiper/washer switch (17A553) and an inline circuit breaker. The front electric windshield washer system consists of a control switch, integral with the turn signal, a windshield washer reservoir (17618) and windshield wiper motor and the necessary windshield washer hoses (17A605) , windshield washer nozzle jet and brackets (17603) and attaching parts.
    ------------------------------------------------------------------------------------------------
    Pivot Shafts and Linkage Removal and Installation
    NOTE: The left and right pivot and windshield wiper adapter and connecting arm clip assemblies are serviced separately.
    1. Perform Steps 1 through 9 of Windshield Wiper Motor Removal as described in this section.
    1. If servicing left windshield wiper adapter and connecting arm clip , remove left windshield wiper mounting arm and pivot shaft and windshield wiper blade assembly.
    1. Remove left windshield wiper adapter and connecting arm clip access cover.
    1. Remove left pivot nut, lower windshield wiper adapter and connecting arm clip and slide it out through left access opening. For installation, follow removal procedures in reverse order. Tighten nut to 10-13 Nm (7-10 ft-lb). Make sure the clip is fully seated in the windshield wiper adapter and connecting arm clip . Do not try to install clip with windshield wiper adapter and connecting arm clip on motor crank pin.
    ----------------------------------------------------------
    Windshield Wiper Motor Windshield wiper motor are not serviceable. If worn or damaged, the windshield wiper motor must be replaced as an assembly. Removal
    1. Cycle windshield wiper blades until in straight-up position and turn ignition switch OFF.
    1. Disconnect battery and wiper motor electrical connector.
    1. Remove the right windshield wiper mounting arm and pivot shaft and windshield wiper blade .
    1. Disconnect the battery ground cable (14301).
    1. Remove the right pivot nut and allow the windshield wiper adapter and connecting arm clip to drop into the cowl top outer panel .
    1. Remove the linkage access cover, located on the right side of the dash panel near the windshield wiper motor.
    1. Reach through the access cover opening and unsnap the wiper motor clip.
    1. Push the clip away from the windshield wiper adapter and connecting arm clip until it clears the nib on the crack pin. Then, push the clip off the windshield wiper adapter and connecting arm clip.
    1. Remove the windshield wiper adapter and connecting arm clip from windshield wiper motor crank pin.
    1. Remove nut and ground strap.
    1. Remove three attaching nuts from windshield wiper motor. Remove the windshield wiper motor .
    Installation
    1. Position the windshield wiper motor and install the three attaching screws. Tighten to 13.6-19.0 Nm (10-14 ft-lb).
    1. Install nut and ground strap.
    1. Connect wiper motor electrical connector.
    1. Install clip completely onto right windshield wiper adapter and connecting arm clip. Make sure the clip is fully seated. Do not put the windshield wiper adapter and connecting arm clip on the motor crank pin and then try to install the clip.
    1. Install the left windshield wiper adapter and connecting arm clip onto the wiper motor crank pin.
    1. Install the right windshield wiper adapter and connecting arm clip onto the wiper motor crank pin. Pull the windshield wiper adapter and connecting arm clip onto the crank pin until it snaps into place. The clip is properly installed if the nib is protruding through the center of the clip.
    1. Install the right windshield wiper mounting arm and pivot shaft and nut. Tighten the nut to 9.5-12.5 Nm (84-110 in-lb). NOTE: When the battery has been disconnected and reconnected, some abnormal drive symptoms may occur while the powertrain control module (PCM) (12A650) relearns its adaptive strategy. The vehicle may need to be driven 10 miles or more to relearn the strategy.
    1. Connect the battery ground cable and turn the ignition switch on. Turn turn signal and windshield wiper switch off so windshield wiper motor will park, then turn ignition switch off. Replace right windshield wiper adapter and connecting arm clip access cover.
    1. Install the windshield wiper mounting arm and pivot shaft and windshield wiper blade assemblies on the pivot shafts to dimension X. Dimension X is the distance between the centerline of the blade saddle and the top edge of the cowl top outer panel grille. The value of Dimension X for each vehicle is given in the Dimension X chart in the Specifications portion of this section.
    1. Test the system.
    6bd608c.gif

    Jan 04, 2010 | 1983 Ford Ranger

    1 Answer

    Wiper motor replacement


    SECTION 501-16: Wipers and Washers 1999 Town Car Workshop Manual REMOVAL AND INSTALLATION Mounting Arm and Pivot Shaft Removal
    1. Disconnect the battery ground cable (14301).
    1. Remove the windshield wiper pivot arms (17527).
      1. Remove the nuts (one each side).
      1. Remove the windshield wiper pivot arms.
    1. Remove the LH and RH cowl top vent panels.
      1. Remove the hood weatherstrip.
      1. Remove the screws.
      1. Remove the retaining clips.
        • Disconnect the LH and RH washer hoses.
    1. Position the windshield wiper mounting arm and pivot shaft (17566) assembly aside.
      1. Remove the nuts.
      1. Remove the bolt.
      1. Position the windshield wiper mounting arm and pivot shaft assembly aside.
    1. Remove the windshield wiper mounting arm and pivot shaft assembly.
      1. Disconnect the electrical connector.
      1. Remove the windshield wiper mounting arm and pivot shaft assembly.
    ----------------------------------------------------------------------------------------
    Motor —Windshield Wiper Removal
    1. Remove the windshield wiper mounting arm and pivot shaft (17566) assembly; refer to Mounting Arm and Pivot Shaft .
    1. Remove the windshield wiper motor (17508).
      1. Remove the output shaft bolt.
      1. Remove the bolts.
      1. Remove the windshield wiper motor.

    May 01, 2009 | 1999 Lincoln Town Car

    1 Answer

    The wiper blade connection has released from the wiper blade motor bar that controls the wipers movement. You can hear the motor working but the arms have been disengaged.


    please rate as fixya if this is what you need. Mounting Arm and Pivot Shaft —Windshield Wiper Removal
    NOTE: The windshield wiper pivot arms (17526) must be in the highest position to remove them.
    1. Turn the ignition switch (11572) to the on position.
    1. Turn the windshield wiper (17500) on.
    1. Stop the windshield wiper pivot arms at the highest position by turning the ignition switch off.
    1. Remove the windshield wiper pivot arm.
      1. Remove the pivot arm nut cover.
      1. Remove the nut.
      1. Remove the windshield wiper pivot arm.

    1. Raise and support the hood (16612).
    1. Remove the cowl grille seal.
    NOTE: The two cowl grilles overlap at the center. The LH cowl grille must be removed first.
    1. Remove the LH cowl grille.
      1. Remove the screw cover.
      1. Remove the screws.
      1. Remove the clips.
      1. Remove the pin-type retainer.
      1. Remove the LH cowl grille.
    6a042b2.gif
    1. Remove the RH cowl grille.
      1. Remove the screw cover.
      1. Remove the screws.
      1. Remove the clips.
      1. Remove the pin-type retainer.
      1. Remove the RH cowl grille.
    bfba69b.gif
    1. Remove the mounting arm and pivot shaft.
      1. Disconnect the electrical connector.
      1. Remove the bolts.
      1. Remove the mounting arm and pivot shaft.
    8169c1e.gif

    Mar 14, 2009 | 2000 Ford Expedition

    1 Answer

    ROVER MGF.REMOVING WIPER MECHANISM.


    Pivot Shafts and Linkage
    The windshield wiper assembly is mounted below cowl top extension (021A36) . Linkages are connected with non-removable plastic ball joints. Windshield wiper mounting arm and pivot shafts are an integral part of the windshield wiper and are serviced as one unit. Removal
    1. Disconnect the battery ground cable (14301). Refer to Section 14-01 .
    1. Remove antenna mast from the antenna base.
    1. Remove cap on LH and RH windshield wiper pivot arms to expose nuts retaining the arms to pivot shafts.
    1. Remove two nuts, one from each of windshield wiper pivot arms . Lift wiper arms to service position, carefully rocking them back and forth to loosen them from the pivot shaft. Lift off windshield wiper pivot arms .
    1. Remove seven screws retaining the cowl top vent panel.
    1. Disconnect windshield washer hose (17A605) at LH side of vehicle just ahead of where it enters cowl top.
    1. Remove hood cowl seal.
    1. Carefully remove cowl top vent panel from vehicle.
    1. Remove three retaining screws to cowl drain tube that is connected to top cowl.
    1. Disconnect wiring harness leading to windshield wiper motor.
    1. Remove five screws retaining cowl top to vehicle and remove cowl top and windshield wiper from vehicle.
    1. Remove two screws and two nuts retaining windshield wiper to cowl top and separate the two parts.
    1. Remove drive linkage from motor shaft linkage.
    1. Remove remaining screws attaching windshield wiper and separate the two parts.
    1086bde.gif

    Item Part Number Description 1 02010 Cowl Top Panel 2 N621906-S2 Nut (2 Req'd) 3 17508 Windshield Wiper Motor 4 N805605-S36 Screw (2 Req'd) 5 17500 Windshield Wiper Assembly A — Tighten to 9-12 Nm (80-106 Lb-In)

    Feb 23, 2009 | 1998 Ford Windstar

    Not finding what you are looking for?
    Cars & Trucks Logo

    Related Topics:

    15 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Cars & Trucks Experts

    yadayada
    yadayada

    Level 3 Expert

    76691 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22219 Answers

    Randy Ohler

    Level 3 Expert

    14585 Answers

    Are you a Car and Truck Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...