Question about Cars & Trucks

Open Question

Fiesta 2004, speedo not working but mileometer is, no abs warning lights and no fault codes!

2004 fiesta 1.25 finesse.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

SOURCE: Ford Fiesta 1998 Finesse 1.3 - imobillisor / ecu fault

hi mate i hade this problem and it were the catlicconverter

Posted on Jun 16, 2008

Ad
  • 24 Answers

SOURCE: speedo and abs light on bmw 5 series

hello , it sounds like you have a bad speed sensor or all 4 of them , see when the speedo plays dead like that is because (most cases ) the sensors at the wheels are bad due to water and normal driving corrosion , the data for the speedo comes from the abs module that monitors the sensors if the abs does not reed it the speedo will not reed it aswell , it will be good to scan the vehicle to see if you need more than 1 sensor there is one in each tire axel ,good luck

Posted on Nov 29, 2008

  • 1 Answer

SOURCE: What Oil for a Ford Fiesta 1.3 Finesse V reg

the correct oil should be W5-30 synthetic!

Posted on Jun 01, 2009

  • 103 Answers

SOURCE: Fault code P1000 [18,2,10,0],Ford Fiesta 2005

P1000 means that you or someone has disconnected the battery,and the car has not been driven far / long enough for the computer to relearn its stratagies.
Engine light could be the fault of the speed sensor, or wiring to the sensor.

Posted on Jul 27, 2009

Bigmick9
  • 18 Answers

SOURCE: Ford fiesta 1.3 01. Engine warning light on

It sounds like a mass airflow sensor

Posted on Sep 08, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

WHAT IS p1143 P1144 ABS CODE FAULT ?


1143 is Air Assist Control Valve Range/Performance

1144 is Air Assist Control Valve Circuit Malfunction
Check the codes again after resetting the fault memory.

Feb 27, 2018 | Ford Cars & Trucks

1 Answer

Ford fiesta 04 aBs light won't go off


The ABS light is on because the system control module has detected a fault in the ABS brakes and the system is turned off and the light is then turned on. You need the ABS scanned as there will be a fault code present.

Jan 09, 2018 | Ford Cars & Trucks

1 Answer

I have a ford fiesta finesse and abs light is on


You need the computer "read" to see which sensor is affected (most common), or what other failure is causing light. Need facility (dealership/other) or go to O'Reillys/etc to use scanner and read code. Usually a bad/damaged wheel sensor at one of the wheels needs replaced.

Jan 09, 2018 | Ford Cars & Trucks

1 Answer

04 Ford fiesta finesse abs light stays on


If a warning light is on, there's a trouble code stored in the computer. There are well over 800-1,000 possible trouble codes in the average late model vehicle, so asking us to guess what's causing your problem without knowing the code is a complete waste of time. Get the code read. Post it here. THEN we can help

Jan 09, 2018 | Ford Cars & Trucks

1 Answer

What Causes abs light staying on, on 10 plate Fiesta Zetec


BAd wheel sensors, bad wiring to the sensors.

Aug 20, 2014 | 2010 Ford Fiesta 1.4

1 Answer

I have a 2004 ford fiesta 1.4 tdci,at the moment the car is still in a non ford garage ,it went in for a osf wheel bearing replaced,it came back to me with the abs light on,after the front wheel was...


abs sensors run very close to the rotor in the disc or hub and can be easily damaged it the play in the failed bearings was sufficient to allow it to touch
when doing the wheels and bearings it is important not to damage the sensor if it was not touching the rotor
if it damaged or the wiring is not connected , the abs light will be on
you can get sensors from the wreckers /junk yard at a good price
after replacing the rear wheel bearings and the hand brake light is on suggests that the correct procedure was not used or the cabling was adjusted off to get the callipers off the disc and not properly adjusted on completion of the job
as the work is being done in a confined space it is possible that a harness plug was disconnected to get access
you have several options
1---have the fault codes read, fix any sensor problem,
2-- take it to an accredited service center that has experience on your make of vehicle as I think that going back to the original shop is not a good idea

Mar 16, 2017 | Cars & Trucks

2 Answers

Hi can i bypass my ABS on my Fiesta 2009. My brakes only works rite when the ABS lights up on the dash....Before it lights up the brake are hard then you have to pump it a little the brake was bleeded


Lots of ways,,
Just pull the fuse ,unhook a wheel sensor,unplug the control box,
Anything to cause a fault,
As long as the ABS light is on you will have normal base brakes.
(I prefer mine like that)
Be sure the RED brake is not on however.
Hope this helps.

Jul 01, 2012 | Cars & Trucks

1 Answer

Fiesta duratec 2005 Abs warning light on


Whenever the ABS module turns on the ABS light in the dash it is to alert you to the fact that a fault has occurred in the ABS system and the control module has turned off the ABS brake control, you now have regular non ABS brakes. The waring light will stay on until the fault is corrected. Since a large number of problems would cause this you must get the control module scanned to retrieve the fault code that was set in the control modules memory when it turned on the light. Once the fault code is known the process of diagnosis and repair can begin.

Feb 10, 2012 | 2005 Ford Fiesta 1.6

1 Answer

Hi, I have a 52 plate ford fiesta with intermittent speedo problems. Speedo goes off and engine light comes on. Any ideas? Sharon


Hi,

When your Engine Check light comes on, it means your computer has detected a fault and wil have stored the code in your computer. This code can be read by your local Ford dealership, using an OBDII scan tool.

An intermittent speedo problem is probably caused by an issue with the Vehicle Speed sensor (or wiring), which is mounted on your transmission case (see No. 7 in diagram below):


wolfman304_36.gif
As you have indicated your vehicle is 2011, you should have this issue rectified under the New Car Warranty and repaired at no cost.


Cheers,

Scott

Jun 13, 2011 | 2011 Ford Fiesta

2 Answers

Ford Fiesta 1998 Finesse 1.3 - imobillisor / ecu fault


hi mate i hade this problem and it were the catlicconverter

Jun 16, 2008 | 1998 Ford Escort

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

john h

Level 3 Expert

14479 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...