Question about Cars & Trucks

Open Question

I need assembly instructions for ethan allen villa media unit

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Insersion ball coupling lock


when you insert the unit into the coupling ,the allen key will be fitted in a hole to enlarge the ball so that it cannot be pulled out . At this point you will remove the allen key and lock it with the keys

Mar 07, 2014 | Cars & Trucks

1 Answer

Timing belt diagram daewoo nubira 1998


Here are the written instructions, i do not have the pictures, it is a very good set of instructions and clearly written.

Required tools:

13mm open end wrench 10mm shallow and deep socket 8mm socket long flathead screwdriver 17mm deep socket T50 torx socket 1/4", 3/8ths and 1/2" ratchets and extensions E10 inverted torx sockets 6mm Allen wrench 15mm open end wrench 7mm socket 12mm open end wrench 14mm socket 12mm socket 8mm, 9mm and 10mm Allen head sockets 19mm socket pry bar needle nose pliers

If you are doing this because your timing belt broke you will also need to buy a complete cylinder head, head gasket set, and both idler pulleys. ALL DAEWOO MODELS WILL BREAK THE INTAKE AND EXHAUST VALVES WHEN THE TIMING BELT BREAKS.

Start by removing the air cleaner assembly from the throttle body, remove the air filter and housing jack up the vehicle and remove the wheel, remove the plastic shielding in front of the accessory drive belt assembly, remove the accessory drive belt, place a jack with a block of wood on top underneath the engine oil pan remove the front engine mount, remove the crank shaft pulley ( the 4 Allen head bolts only not the 17mm bolt in the center.) remove the metal plate behind the engine mount bracket on the engine, remove the plastic timing belt cover 3 clips on top 2 10mm bolts on bottom. Rotate the engine until the #1 cyl. is at Top Dead Center on the compression stroke or line up the crankshaft timing mark with the mark on the inner timing belt cover ( notch in cover with notch in pulley) on the camshaft pulleys -- ( intake cam line up the line on the pulley with the line on the inner cover)( exhaust cam line up the arrow on the pulley with the arrow on the inner cover) loosen the 13mm bolt in the belt tensioner and using the Allen wrench rotate the tab until there is slack in the belt. Remove the belt. At this time I would recommend you replace the water pump, both plastic idler pulleys as they tend to overheat and lockup, and the belt tensioner. Make sure all your marks are lined up, you may need a helper to hold the Exhaust Cam in place as it tends to move during belt installation. Put the timing belt underneath the crankshaft pulley, install the belt leaving the intake cam for last and NO BELT SLACK on the right side between the crank and the exhaust cam. Once the belt is installed rotate the crankshaft over 2 revolutions and make sure is rotates freely, and your timing marks are aligned perfectly if not the engine will not run properly, tension the belt as needed. Installation is the same as removal.

Nov 15, 2011 | 1999 Daewoo Nubira

1 Answer

I can't remove the hex bolts off the top of the plastic engine cover in order to remove the cover and get at the seal. What size of allen wrench should I be using


No maintenance manual specifies hardware sizes - they change at the whim of assembly line workers and/or assembly line suppliers (though they do tend to remain the same throughout a model year). Do what mechanics do with hardware: buy a whole set of metric allen wrenches and keep trying until one fits.

Sep 30, 2011 | 2005 Chevrolet Aveo

1 Answer

How hard is it to replace a rear strut


it is fairly easy
1. jack up remove wheel, block car on frame!!! not on the strut
2. remove two big bolts on bottom of strut then have to drive them out of hub housing (splined about 1 inch on head side of bolt.
3. remove the sway bar connector rod (allen key and wrench. or if allen is stripped u can use wrench just in front of boot, so one inside and undo the one nut you can see facing you)
4. open trunk pull carpet back on top of wheel well so you can see 3 nuts in a triangle with one in the center DO NOT REMOVE CENTER NUT this is what holds spring to strut assembly..put a jack under strut to hold it in place .remove the 3 nuts.
5. pry the bottom of strut out of hub
6. drop out strut and spring assembly.
7. use 2 spring depressors to squeeze the spring so u may remove large center nut, use wrench and allen key.
8. replace as a whole unit or just the strut. the whole unit is more expensive and if so delete step 7
9. reverse the steps to install.
10. make sure all bolts are tight and check with torque wrench for proper tightness.
11. MAKE SURE LOL you dont want to go for a drive with any of these parts loose. If u r not experienced take it to a shop.

Dec 05, 2010 | 1998 Pontiac Grand Prix

3 Answers

2008 volvo xc90 rear tail light bulb out. trying to remove unit. only one allen type bolt. plastic unit will not budge. chipped edge already. very fustrated. what should I do?


This assembly give the dealer ship tech problems, poor design. I recommend you take it in o local dealer and have all your taillight bulbs replaced.
Because the other bulbs that still work is right behid the one that is burned out. (the life is the same)
It not worth the fustration, trust me.

Sep 26, 2009 | 2008 Volvo XC90

1 Answer

Oil filter assembly


It's a spin on filter which just screws off counter clock wise. Then you spin on the new one after lubricating the seal just hand tighten. Instructions on filter usually Are you sure your are talking about the oil filter? The treaded stud that the oil filter screws on to is removable also but I have never seen one come out unless you make a concerted effort with an Allen key

Jul 03, 2009 | 2003 Saturn L-Series

1 Answer

Replacing front brake pads on detached caliphers


Hi my name is Allen!

Its extremely hard to explain how to install front brake parts without some sort of diagram. Here is what you can do, go to your local library and you can print out the diagrams you need, copies are only about ten cents a copy.

For further asistance you may reach me at FixYa!

Dec 27, 2008 | 1994 Dodge Grand Caravan

1 Answer

2005 Ram 1500: Removing headlight unit.


Hi my name is Allen!

If all you are doing is replacing the bulbs for brighter ones, then there is no need to remove the headlight assemblies. Just reach behind the headlight assembly and unplug the connector from the bulb then turn the locking nut and pull the bulb out of the light assembly and replace the other one.

For further asistance you may reach me at FixYa!

Dec 25, 2008 | 2005 Dodge Ram 1500

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

18 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...