Question about Audi A4

Open Question

Hi. What tools would I need to remove and replace the throttle body (inlet manifold flap motor) on my 2006 Audi A4 tdi? Any help will be appreciated.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

peidavey
  • 14 Answers

SOURCE: replace blower motor

check out http://forums.audiworld.com/forum

tons of help to be had there.

Posted on Dec 31, 2008

TLRogue
  • 99 Answers

SOURCE: temperature sensor audi a4

Possibly located at the back of the engine behind cylinder head, usually located in a small plastic hose block.

TL

Posted on Jan 23, 2009

  • 21 Answers

SOURCE: Audi A4

Not sure if they've changed it but this is what i do for my 99 a4

First remove the screw in the handle pull, it should be next to where your fingers go.
Pull down on the black piece of plastic and remove the screw form the door
Then remove the screws on either end of the door, one near the door jam on top and one near the other side, same place.
Finally pull up then out and the door panel should come out

Hope that helps

Posted on Jun 17, 2009

venexcsd
  • 1185 Answers

SOURCE: FOCUS 1.6 ZETEC CLIMATE TDCI 2006- FAULT CODE P242F

If the cat was blocked you would have noticed a massive power loss and your speed would have been down to - 40kph

If that was the case then yes the cat has collapsed and needs replacing

Posted on Jun 30, 2009

  • 5 Answers

SOURCE: I have a Audi A4 1.9 tdi 1997, the fan belt has

7f510dc.png it a bit of a simple drawing but thats how it go's hope this helps

Posted on Jul 06, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Throttle body sensor location 2005 uplander


the sensor is part of the throttle body and not replaceable here is the throttle body replacement instructions as you will have to replace the entire throttle body it is a very common issue with these
THROTTLE BODY ASSEMBLY REPLACEMENT

REMOVAL PROCEDURE
  1. Remove the air cleaner intake duct.
120434113
  1. Disconnect the electronic throttle control (ETC) electrical connector (1) from the throttle body (2).
113356645
  1. Remove the heater pipe nut at the throttle body.
  2. Remove only the heater inlet pipe.
113356646
  1. Remove the nuts and the bolts from the throttle body.
  2. Remove the throttle body assembly.
  3. Remove the throttle body gasket.
  4. Clean and inspect the throttle body gasket mating surfaces.
NOTE: Do not use solvent of any type when cleaning the gasket surfaces on the intake manifold and the throttle body assembly, as damage to the gasket surfaces and throttle body assembly may result.

Use care in cleaning the gasket surfaces on the intake manifold and the throttle body assembly, as sharp tools may damage the gasket surfaces.

INSTALLATION PROCEDURE
113356646
  1. Install a new gasket, if necessary.
  2. Install the throttle body assembly.
  3. Install the throttle body nuts and the bolts.
NOTE: Refer to Fastener Notice in Service Precautions.

Tighten the nuts and the bolts to 10 N.m (89 lb in) .
113356645
  1. Install the heater inlet pipe.
  2. Install the heater pipe nut to the throttle body.
Tighten the nut to 25 N.m (18 lb ft) .
120434113
  1. Connect the ETC electrical connector (1) to the throttle body (2).
  2. Install the air cleaner intake duct.

Feb 03, 2014 | 2005 Chevrolet Uplander

1 Answer

Need to know how to replace the thermostat on a 1996 buick century wagon 3.1 6 cylinder engine



Trace the upper radiator hose to the mounting area on the intake manifold. Loosen the hose clamp on the manifold end of the hose and remove the hose. Pull the thermostat out of the intake manifold.

For more help and troubleshooting go through the help links below:---

Click the link below:-----





THERMOSTAT REMOVAL PROCEDURE/LOCATION DETAILS

------------

Where is Thermostat Located on Saturn

http://technoanswers.blogspot.com/2012/11/where-is-thermostat-located-on-saturn.html

----------

2004 Dodge Intrepid: How to replace Thermostat?

http://schematicsdiagram.blogspot.in/2012/06/2004-dodge-intrepid-how-to-replace.html

---------

How to Replace Thermostat on Audi A4?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-thermostat-on-audi-a4.html

---------

How to replace Thermostat on Acura Car models?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-thermostat-on-acura-car.html

-------------

Where is thermostat located on 2006 dodge magnum 3.5L?//

http://repairhelpcenter.blogspot.com/2011/10/where-is-thermostat-located-on-2006.html


----------

Thermostat on AUDI 1.9 TDI?

http://repairhelpcenter.blogspot.com/2011/10/thermostat-on-audi-19-tdi.html

-----------

How to replace Radiator on Audi and VW car models?

http://repairhelpcenter.blogspot.com/2011/11/how-to-replace-radiator-on-audi-and-vw.html


--------------

How to Replace a Thermostat.

http://schematicsdiagram.blogspot.com/2011/07/how-to-replace-thermostat.html


-------------

How to locate Thermostat on Any car model?

http://schematicsdiagram.blogspot.com/2011/12/how-to-locate-thermostat-on-any-car.html

--------

Where is thermostat on Audi A6?

http://technoanswers.blogspot.com/2011/12/where-is-thermostat-on-audi-a6.html

-------

How to replace thermostat on 1992 Buick century?

http://technoanswers.blogspot.com/2011/12/how-to-replace-thermostat-on-1992-buick.html

------

Replacing thermostat on 1999 Mercury Cougar?

http://technoanswers.blogspot.com/2011/12/replacing-thermostat-on-1999-mercury.html

------

Thermostat Replacement on Toyota Corolla?

http://technoanswers.blogspot.com/2011/12/thermostat-replacement-on-toyota.html

--------

Where is thermostat located on 2005 Dodge neon?

http://schematicsdiagram.blogspot.in/2012/02/where-is-thermostat-located-on-2005.html
--------
These will help.
Thanks.

Nov 28, 2012 | Buick Century Cars & Trucks

1 Answer

How do you replace a throttle position sensor on a 2006 Chevy Aveo


seddy29732_0.jpgThis is a picture of your throttle position sensor. It is located on the throttle body, where the air inlet tube enters the intake manifold. Simply unplug the wires, remove the bolts holding it in place, and replace it with the new unit. Hope this helps!

Jun 02, 2011 | 2006 Chevrolet Aveo

1 Answer

I have a 1999 audi A4 1.9 tdi estate, the heating system has stopped blowing warm /hot air . all the vents still work and the fan sometimes there is a clicking noise from the system is this a thermostat...


From the clicking noise,its a flap motor thats stuck closed.You should have an error code for this if you use Vag-com diagnostics.
On a LHD car,the flap motor thats is usually problematic,is on the right under the glovebox.I usually just take the motor apart .lubricate it and its fine again...way cheaper than buying a new one.
Good luck.

Feb 18, 2011 | 1999 Audi A4

1 Answer

Hi I'm emailing from Ireland having just been given a quote of ?625 to replace inlet manifold flap motor and relay under fuse box. From looking online it would appear these parts which i am being quoted...


Most repair shops will allow you to purchase your own parts. But if the part fails, they will charge you to take it off and reinstall another one.

Oct 27, 2010 | 2006 Audi A3

1 Answer

How to remove the intake manafold cover to get to the spark plugs


need more info, what size engine? what model need that to send u the correct RnR of the upper plenum

here is the 3.5L version of removal:
  1. Disconnect and isolate the negative battery cable.
  2. Disconnect the Inlet Air Temperature (IAT) sensor electrical connector
  3. Remove the air inlet hose from the throttle body.
  4. Disconnect the Manifold Absolute Pressure (MAP) sensor electrical connector.
    1. Disconnect the PCV hose ,purge hose and power brake booster hose from the upper intake manifold.
    2. Disconnect the electrical connector from the electronic throttle control .
    3. Remove the fasteners from the throttle body and cylinder head and remove the throttle bracket.
    4. Remove the wiper module, strut tower support and EGR tube
    5. Disconnect the electrical connectors from the manifold tuning valve
      1. Remove the fasteners , from the intake manifold support brackets.
      2. Remove the upper intake manifold retaining bolts, insulation foam pad and manifold. Clean all gasket sealing surfaces.

Sep 02, 2010 | 2006 Dodge Charger

1 Answer

Blower motor instilation


you don't need to take the dash out , the motor is on the top of your glove compartment, 5 bolts for the glove compartment an 3 for the blower it's a 20 min job .

Jan 07, 2010 | 1998 Audi A4

2 Answers

Hi my audi 1.9 tdi is losing power badley the acceliration totaly went its just had a new turbo so i dont think its the turbo. I,ve been out in the car a few times and the problem seems to come and go...


If somebody replaced the turbocharger with a new one, you must check up all command vacuum lines, the entire air intake system (air pressure pipes, intercooler, connections, EGR - throttle vane, ...), and also turbocharger and EGR command solenoid valves (three pieces). Could be also MAF sensor defective! Here you have the vacuum air pipes connection picture for Audi A4 1.9 TDI (AJM engine):
4d2f5b6.jpg Please Rate my Response! Thanks!

Sep 01, 2009 | 2002 Audi A4

1 Answer

Audi flywheel - 1.9 tdi


you can use one off a vw passat

Aug 19, 2009 | 2003 Audi A4 Cabriolet

1 Answer

How to replace engine air filter


  1. Disconnect negative battery cable.
  2. Disconnect inlet air temperature sensor electrical connector.
  3. Disconnect fresh air makeup hose from throttle body air inlet hose.
  4. Disconnect PCV hose from intake manifold.
  5. Loosen hose clamp at throttle body air inlet hose. Remove hose from throttle body
  6. Push in on locking tabs to disengage air inlet hose from air cleaner housing. Remove throttle body air inlet hose and air cleaner element together.
  7. Separate air cleaner element from throttle body air inlet hose.
INSTALLATION reverse

Jun 11, 2009 | 2002 Chrysler Sebring

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75117 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14228 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...