Question about Cars & Trucks

Open Question

Cannot open my miroku mk38 without removing the fore end.

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove ventilation blower motor


To do it properly you are going to need a Chilton's or Haynes type servive manual for you car. It will take you through the whole process. If you fore go it I bet you end up taking off more than you need to. I have been through it before. Or ask a service guy where it is maybe he will tell you all the parts to remove. Tough job done envy you a bit.

Jan 29, 2015 | 2011 Mazda 3

1 Answer

How do i take the fuelpump out of the plastic casing without breaking the plastic on a 2001 chevy prizm


If I understand you correctly you want to remove the pump from that plastic bracket that holds it. Hold the Fuel Pump Strainer side up and you will notice one end of the retainer is open as it is shaped like a "C". Pull the bracket away from the pump and the open end will allow it to come free and then remove the other end from its connection.

Jan 28, 2015 | 2001 Chevrolet Prizm

1 Answer

How do you remove the front bumper of a Mercedes Benz cl65 amg


Lift the front end of the car and support on stands.
Remove the front wheels.
Remove the fowards under-tray.
Remove the forward halves of the front wheel arch liners.
Unscrew the small down-facing Torx screw at each top rear corner of the bumper.
Gently pry inwards the rear end of the U-shaped steel channel that holds the fender and bumper flanges together.
Pull the channel rearwards to disengage the lugs from the diagonal slots at the forward end, and remove the channels.
Disconnect the external air temp sensor in the bottom left air intake.
Disconnect the parking sensors connector at the right rear corner. You need to open the lever lock and pull hard without damaging the wiring.
Open the hood and remove two bolts on top of the bumper, next to the inner headlamp mountings.
Remove two nuts in lower grille - vertically beneath above bolts.
If its your first time, get a friend and pull the bumper forwards very slowly and gently, avoiding scratching the fenders.
The bumper is surprisingly light.

It will take about an hour.

Jul 02, 2014 | Cars & Trucks

1 Answer

How to take off the top ball joint nut with an open end wrench without stripping the nut?


Usual method,Pull the cotter pin and use 2 open end wrenches,on top of each other to increase the contact area and pull slowly.The nut should come off.
2nd method,use a sharp air chisel and split the nut apart.
3rd method,shield the CV boot and heat the nut or cut it off flush with a torch.
4th method,freeze the nut with 134a and then remove it with the 2 wrenches.
5th method,Cut across it at an angle with an air cut off tool
down to the ball joint threads to release the nut pressure then remove it with one wrench.
Do you need more methods?

Apr 26, 2017 | 1996 Nissan Maxima

1 Answer

Keys locked in ignition on freelander td4


Are the keys locked in the car if yes you can use a wooden wedge in the top of your door and a wirer coat hanger starihting it out with a little hook on the end to hook on to the door release ,be very careful with the wood do not fores it in to much are you will bend the top of your door

Jan 16, 2013 | 2002 Land Rover Freelander

1 Answer

Change disc front breaks 2001 seville


jack up the car and remove the tire. you will see a caliper that is the thing that looks like it is hugging the disc. there are 2 bolts on the back side of the caliper. one on top one on bottom. loosen them and then they slide back out of the way. the caliper will then slide off. remove the old brake pads. use a 4 inch C clamp with the threaded end inserted to the cup part of the caliper and the stationary part on the opposite side and tighten the clamp down slowly. this will open the caliper back up so it will fit over the new brake pads. after you have the new pads in place slide the caliper over the brakes and disc realign the bolts that hold the caliper in place, tighten, replace tire and repeat on the other side. once complete make sure you pump the brakes a few times be fore you move the car so the caliper can close in on the new brakes otherwise you won't have any brakes for the first few pumps of the pedal

Jul 14, 2012 | 2001 Cadillac Seville

1 Answer

How do I repair lifters on 99 surburban?


youll have to remove the intake mainfold both valve covers and remove the rocker arms the other end of the push rod is where the lifters are there may be a plate there i never did a suburban be fore be a lot of fords back in the day not to many probs this days with lifters

Nov 18, 2011 | 1999 Chevrolet Suburban

1 Answer

Drivers seat motor wont go back or forward but will go up and down


maybe something jammed in the rails or damaged motor. Up & down is ok because it has seperate motor. Easy to remove seat and have a look at the set up. Basically it's a long screw on the end of a motor that drives thru a captive nut in the seat. Sometimes the captive nut wears and causes "seat rock" fore and aft.

Aug 18, 2010 | 1997 BMW Z3 Roadster

1 Answer

1995 Fore Escort, how do I replace the negative battery cable?


Disconnect battery cable & then the bolt or nut that connects other end to engine ground. You may have to disconnect & replace later a couple of other hold down ties to cable. Good luck!

Dec 31, 2009 | 1995 Ford Escort

1 Answer

My wife's M'reg C200's SRS light comes on at start-up and is taking 1-2mins until it goes out any ideas Regards Miroku Mike.


This is most likely caused by low voltage but you should bring it to your local merc service centre to have a scan to be sure as it is a safety issue.

Jul 04, 2009 | 2003 Mercedes-Benz C-Class

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...