Question about Cars & Trucks

Open Question

Hi after putting new gearbox on 06 vectra in now wont startgot ignition but no power to starter

Posted by on


4 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017

  • 76846 Answers

SOURCE: hi i had a new clutch and recon gearbox 20/06/08

no recalls for this show up.

Posted on Sep 14, 2009

  • 4793 Answers


would you believe you fill up by pouring oil down dipstick tube....why would you want to,it is sealed/non maintenance.....

Posted on Mar 03, 2010

  • 29 Answers

SOURCE: car wont start put new ignition switch and same prob I have power on acc but not forward no dash lights or starter. i can manually jump starter and checked fuesablb link what is the issue

check your grounding conductor, connection to earth, check for open path or short.... if your grounding point of contact with earth is not super clean and rust free, then it wont start but you will have power on acessory because it uses a different grounding point (batteries main earth connection).
Also, use a meter to check continuity of conductors to and from starter and it will show a short if the OHM reading says "overload", but disconnect battery first to be safe.

Posted on Aug 17, 2012

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

2006 Xterra wont crank

Check the battery cable where it connects to the engine block or gearbox. A 'bad earth' can cause the symptoms you describe.

Oct 14, 2017 | Cars & Trucks

1 Answer

Iv put new heater plugs in my vectra a new egr valve on + when left for a few hours it takes ages to start? it a 2005 vectra 1.9 ctdi

just because. the glow plugs are new, does not mean they work correctly, not at all. (yes, they can have weak or now power to them)
1: glow plugs work. really.
2: fueling correct. (fuel filter new, ?)
3: hearty battery and starter cranks nice and fast.

1,2,3, if not scan it.

Jul 18, 2014 | 2005 Opel Vectra 1.9

1 Answer

06 equinox wont start.

Did you check the relay? Maybe swap it with another and see if that works.

Feb 06, 2014 | Chevrolet Equinox Cars & Trucks

1 Answer

Hi, I own an accent CRDi '06. My problem is that, engine wont start in the mornings. But it does start on push start. After that it runs normally throughout the day and starts normally. I've checked...

when you try to start engine does the starter motor engage or do you hear a clicking ? also when you turn on ignition do you hear a click ?

Jun 14, 2017 | 2003 Hyundai Accent

1 Answer

Vectra 2.2

Hi my vectra did this and didn't show a fault code it's the crank shaft position sensor located behind the starter motor on the front of the engine the sensor is about 30 pound mines never cut out sins i change my spark plugs and coil pack to trying to figures out who knew it was a little sensor it through a your crank shaft outta wack and it throws through a lot of petrol otta timing cheers scott

Aug 31, 2012 | Vauxhall Vectra Cars & Trucks

1 Answer

93 grand cherokee wont start put a new starter in and have power everywhere just wont start

Hi, I will try and be of some help to you.
The starter has a big terminal on it , which should be live at all times ( +cable from the battery ).
Then there is a small wire on the small terminal which is what activate`s the starter.
To check this circuit ( please be careful when doing this test )
With the ignition `OFF` use a screw driver to make a contact from the big terminal to the small terminal momentarily.
If the engine turns over, then the problem is the circuit between the starter and the ignition switch
Ihope i have been of some help to you
Happy easter john (south wales uk )

Apr 22, 2011 | 1993 Jeep Grand Cherokee

2 Answers

What is the basic process when the car wont start? Battery is good... I know I should check the starter next, but I'm not sure where the starter is or exactly what it looks like...

next.gif getimage.php? it looks like this if your car wont turn over is a possibility, that the starter is bad, try to hit the starter motor before you remove ie and triy to start it see what happens, hit it hard, if it starts you need a new starter.the starter is near the transmission underside.

Sep 10, 2010 | 1997 Volkswagen Jetta

1 Answer

No power to the solenoid on the starter

There is no relay for the starter motor.Disconnect the plug from a tumbler and just short the positive wire with starter motor one.If O.K. the problem is into ign.switch.If your VW have automatic gearbox-check parking switch on gear lever.

May 06, 2010 | 1998 Volkswagen Jetta

5 Answers

Vauxhall vectra problem

Only way to check out the problem for sure is to drop the gearbox out and examine the clutch. Having gone this far in to the internal workings. It would make best sense to replace the clutch and pressure plates. Oil leaks can be repaired at the same time. No need to go to a main dealer because clutch replacement on a V6 is technically a very similar and no more difficult to replacement on any other Vectra

May 30, 2008 | 1997 Acura CL

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

21 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

76846 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides