Question about Cars & Trucks

Open Question

My 98 ECLIPSE 2.0 NON TURBO CAM GEARS HAVE 4 TIMING MARKS 2 ON EACH GEAR. WHEN I LINE INTAKE AND EXHAUST FACING EACH OTHER SHOULD BOTH CAM DOWELS BE FACING UP

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

alicantecoli
  • 22156 Answers

SOURCE: 1998 zx2 timing

timing mark is on flywheel for crank and on the rear end of the cams under the rocker cover.be carefull with this as the pulleys do not have keyways and can come loose resulting in smashed valves and piston.make sure retaining bols have locktite or better still araldite on the threads and use a impact gun on them.fairly easy job to do though,make sure you remove tensioner though and remove the dust cover and give a little drop of oil and some new grease then push seal cover back on ,saves the cost of a new bearing as these are not cheap.

Posted on Nov 09, 2008

SOURCE: 2001 volvo v70 2.4 non turbo timing belt allignment marks

Not sure if it is possible to have it run smoothly by being off a tooth.

The hash marks on the cam pulleys line up with the timing belt cover that goes over those pulleys. Should be two notches in the cover.

As for the lower marks...those aren't really visible till the lower aux. belt pulley is removed. Then you'll have a clear view of the line up marks. One on the inside and one on the outter area of the pulley itself.

When you put the t-belt on...it is a good idea to replace the tensioner as well.

Also when you have the new belt on...adjust the tensioner so that the handle looking thing is centered between the two notches that hold the tensioner in place to the block.

After putting all that together, its a good idea to rotate the timing belt two to four rotations till the marks all line up again. That will let you know if you are hitting the valves or not.

Posted on Jan 27, 2009

  • 73 Answers

SOURCE: 96 camry 2.2L, What timing marks do you use to

the 2 single dots on the inside of the gear(side facing the rear of the motor) When the gears mesh together the 2 dots should line up.

Posted on Sep 21, 2009

jturcotte
  • 8215 Answers

SOURCE: 2001 2.4l turbo timing marks see marks on cam

everything is at 12 o'clock. see diagram from autozone.com

1515ac4.gif

Posted on Sep 29, 2010

jyackle5
  • 8197 Answers

SOURCE: I've got a 2001 kia

On the pictures below will show you the proper marks of the gears.

Align the crankshaft marks before removing the timing belt - 2.0L (VIN 3) Engine


4c597c5.jpg
Proper alignment of the intake and exhaust camshaft pulley timing marks- 2.0L (VIN 3) Engine

8470569.jpg
Or you can go to autozone.com click on repair info then ad your car under manage my vehicles. You might need to sign in it is free though.

Good Luck please accept the answer

Posted on Oct 30, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you adjust valves on a 2006 3.5L V6 Toyota Avalon?


There is a Toyota Technical Service Bulletin issued for this:-
T-SB-0291-08 September 11, 2008 2GR-FE Valve Timing

Procedure Service Category Engine/Hybrid System Section Engine Mechanical Market USA Applicability YEAR(S) MODEL(S) ADDITIONAL INFORMATION 2005 - 2009 Avalon 2007 - 2009 Camry VDS(s): BK46K 2008 - 2009 Highlander 2006 - 2009 RAV4 Engine(s): 2GR VDS(s): BK31V, BK32V, BK33V, BK34V, ZK31V, ZK32V, ZK33V, ZK34V, ZK35V 2007 - 2009 Sienna Introduction This service bulletin provides information regarding valve timing inspection and service guidelines for vehicles equipped with 2GR-FE engines. © 2008 Toyota Motor Sales, USA Page 1 of 5 T-SB-0291-08 September 11, 2008 Page 2 of 5 2GR-FE Valve Timing Procedure Introduction (Continued) Figure 1. 3 2 1 5 9 8 7 6 4 1 RH Bank Intake Camshaft Timing Gear 2 RH Bank Exhaust Camshaft Timing Gear 3 RH Bank No. 2 Timing Chain 4 Crankshaft 5 Idler Gear 6 Timing Chain 7 LH Bank No. 2 Timing Chain 8 LH Bank Exhaust Camshaft Timing Gear 9 LH Bank Intake Camshaft Timing Gear Warranty Information OP CODE DESCRIPTION TIME OFP T1 T2 N/A Not Applicable to Warranty © 2008 Toyota Motor Sales, USA T-SB-0291-08 September 11, 2008 Page 3 of 5 2GR-FE Valve Timing Procedure Inspection 1. Set the No. 1 cylinder to TDC/compression. A. Set the timing mark to 0 on the timing chain cover by rotating the crankshaft clockwise. B. Verify the timing marks on the camshaft timing gears are in general alignment with the timing marks of the camshaft bearing cap: TIMING MARK IDENTIFICATION CYLINDER BANK INTAKE GEAR MARK EXHAUST GEAR MARK RH Bank (Bank 1) Small Mark Single Line LH Bank (Bank 2) Large Mark Double Line HINT When the engine is correctly timed, the timing marks will NOT perfectly align. Figure 2. Figure 3. RH Bank Exhaust Camshaft Timing Gear 1 2 1 Bearing Cap Timing Mark 2 Gear Timing Mark Figure 4. RH Bank Intake Camshaft Timing Gear 2 1 1 Bearing Cap Timing Mark 2 Gear Timing Mark © 2008 Toyota Motor Sales, USA T-SB-0291-08 September 11, 2008 Page 4 of 5 2GR-FE Valve Timing Procedure Inspection (Continued) Figure 5. LH Bank Intake Camshaft Timing Gear 1 2 1 Bearing Cap Timing Mark 2 Gear Timing Mark Figure 6. LH Bank Exhaust Camshaft Timing Gear 1 2 1 Bearing Cap Timing Mark 2 Gear Timing Mark HINT If the timing marks appear vastly out of alignment, turn the crankshaft one revolution (360 ) clockwise and note the position of the timing marks. Component Removal Guidelines 1. If engine disassembly is required that involves removing the camshafts or timing gears, set the #1 cylinder to TDC compression, wipe away any oil, and mark the following items in relation to each other prior to disassembly: • Timing gears • Timing chain • Timing chain No. 2 NOTE This relationship MUST be maintained. The intake gear is timed in relation to the crankshaft via the timing chain; the exhaust gear is timed in relation to the intake gear via the No. 2 timing chain. © 2008 Toyota Motor Sales, USA T-SB-0291-08 September 11, 2008 Page 5 of 5 2GR-FE Valve Timing Procedure Component Removal Guidelines (Continued) 2. If NEW camshaft timing gears or the No. 2 timing chain are being installed, the two yellow links on the No. 2 timing chain can be used to ensure correct relationship between the intake timing gear and the exhaust timing gear. Figure 7. 1 1 Yellow Link A. Align the paint mark on the timing chain with the intake gear timing mark (to ensure the intake gear is correctly timed to the crankshaft). Figure 8. RH Bank and LH Bank 3 3 4 3 3 4 5 4 5 4 1 2 1 RH Bank 2 LH Bank 3 Yellow Link 4 Gear Timing Mark 5 Timing Chain Paint Mark B. Align the two yellow links on the No. 2 timing chain to the timing marks on

May 04, 2015 | 2006 Toyota Avalon XLS

1 Answer

Need timing marks for 1993 1.6 Toyota Corola camshafts


If its the 1.6litre 4afe. Turn the crankshaft to TDC, ie. Tiny slit on the crank pulley should be straight underneath the 0deg mark. The cams, intake cam is driven off the exhaust cam by means of two gears. Installation marks. They have 4 holes in front of the gears. Front being closest to timing belt. Upon installation one hole in each gear should face upwards and the other holes should face each other between the gears. On the exhaust cam pulley there is a hole drilled through it, ie. timing mark. It should face up. Directly inline with the grove in the first cam cap. If you have 1.6litre 4age engine. Between cam gears and cylinder head there should be a plate. groves in cam gears should face the groves in the the plate.

Oct 19, 2014 | 1993 Toyota Corolla

1 Answer

Toyota timing marks


One mark is on cam gear mark on head line it hole in gear
camshaft intake and exhaust valve rocking that. Tic then on the back of two cam gears have to ,match up turn and match two sets of marks then back to tic them crank gear
one is straight up replace belt I would change water pump and seals also? good luck

Aug 12, 2014 | 1998 Toyota Camry

1 Answer

2007 huyndia tucson 2.0 i need the timing marks on exhaust cam and inake cam on the chain


Exhaust camshaft gear and Intake gears have dots on them, chain has colored links. Align colored links to dots or count 14 links from ex cam dot to intake dot. Make sure that the mark on the cambelt side is set first on ex side. Small hole on ex cam gear (cambelt) side to line up with mark on head.

Apr 07, 2014 | 2009 Hyundai Tucson 2.0

1 Answer

Where are the timing mark located on a 98 s70 Volvo?


There should be a little notch on each cam gear that lines up with a notch on each side of the cam cover.
Try looking at it from the side and rotating the engine with a large ratchet on the crank bolt (turn clockwise only).

The timing marks will line up every TWO rotations. You'll see how the notch on intake and exhaust cam gears both line up with the notches on the plastic cover.

Oct 02, 2013 | 1998 Volvo S70

1 Answer

Do you know the marks for cambelt in a holden astra 2001. We thought we had it but now the whine won't fire up! Any suggestions??


hey mate.when you look at the cam gears you will see the timing marks like 2 lines carved in the gear.when setting the timing these 2 marks need to line up and look at each other.the intake cam mark should be at 3oclock and the exhaust at 9oclock.
use cam lock.

Sep 14, 2013 | Cars & Trucks

1 Answer

What are the timing marks and how does the timing belt line up for a 2000 KIA Sportage 2.0 4 cylinder?


intake cam gear line the "i" up with the dimple in the rear timing cover
exhaust gear line up the e with dimple on rear timing cover above letters there should be a mark on one of the teeth line it straight up with the coorsponding dimples in the black steel cover behind gears

Jun 27, 2010 | 2000 Kia Sportage

1 Answer

Timing marks for the Dodge 2.4L caravan, 2000


To align both sets of timing marks, turn engine crankshaft to the right with belt on cam and crank. Once you have done this the crankshaft alignment mark (on front of crankshaft gear) will line up with mark to the rear of gear on engine block.The two cam gear timing marks should be alines across from one another. The right cam gear is the intake side and the left side is the exhaust side. After removing the belt turn the exhaust cam down 1/2 notch. Timing mark on exhaust 1/2 notch down from the intake side. Install new belt and recheck everything to make sure it's all correct. Hope this will help you.

May 16, 2010 | 2000 Dodge Caravan

1 Answer

How do you replace timing chain in a1988 chevy s10 with a 2.8 where are marks on gears set do you use #1 top dead center or #4 tdc


Line up the crank gear timing straight up, line up the cam gear timig mark straight down (so the marks are closest to each other, or facing each other). the distributor will be firing #4.

Mar 05, 2010 | 1988 Chevrolet S-10

3 Answers

96 camry 2.2L, What timing marks do you use to


the 2 single dots on the inside of the gear(side facing the rear of the motor) When the gears mesh together the 2 dots should line up.

Sep 20, 2009 | 1993 Toyota Camry V6

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

19 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Randy Ohler

Level 3 Expert

14585 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...