Question about Cars & Trucks

Open Question

Need fuel line in motor hoses where to replace them. The wiring system and having trouble with one engine mount

For pajero 2001 petrol 3.5 ltr

Posted by on


6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

  • 117 Answers

SOURCE: Engine motor mounts on 2001 PT Cruiser

Place a block of wood under the engine sump to prevent damage when you jack up the engine to take the tension off the mount. Make sure you do not jack the engine up too much as you might damage the exhaust,cooling hoses etc.

Posted on Apr 07, 2009

  • 4669 Answers

SOURCE: replace the engine motor mounts and the transmission mount. Would like to know how to do it. Thanks.

Check the frame mounts too. You will have to loosen the bolts and jack the motor up with a jack and a woodblock.

Posted on May 04, 2009

  • 1 Answer

SOURCE: location of 02 sensor bank 1 sensor 1 on 3 ltr engine

it's right adjacent to the cataytic converter

Posted on Jun 11, 2009

  • 396 Answers

SOURCE: replace lowerr right motor mount on dodge 2001

Yes you can. Just put the car on JACK STANDS, As you will need to raist the engine slightly with a jack to take the load off of the mount to remove it. Buy the new mount first, so you will see where the bolts go. BE safe and don't rely on a tire jack

Posted on Feb 02, 2010

  • 6 Answers

SOURCE: I need wiring diagram for 2001 Saturn L300, I also fuel sys dgrm

Mine was doing same, but also revving up weird. I replaced the Crankshaft position sensor and it didnt work. Today I changed the Engine coolant temp sensor and it fixed my problem. Hope this helps!!

Posted on Mar 30, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Can a 1984 pajero 4 cylinder engine be mounted into a 1989 V6 pajero body?

Apart from engine mounts. exhaust system. gearbox flange to engine block wiring , fuel line you could probably do it but be prepared for a lot of work. Best check it out with a modifier club first

Feb 07, 2013 | Cars & Trucks

2 Answers

Can i convert a gasoline Pajero Io to Diseal by changing the engine

yHi,, yes you can, however there are a few more conversions you will need, or a few things you need to ensure I'll list them for you.

1.) engine and transmission (some times) nneds to be replaced.

2.) the fuel pump and fuel lines. (if your pump isnt powerful enough you will need a stronger one)

3.) the electrical system needs to be adapted to the new engine. (like your starter and ignition wiring)

Dec 28, 2012 | Mitsubishi Pajero Cars & Trucks

1 Answer

Replacing the engine

3 engine mount pivot slide bolts and the trannny mount, but that is not the real challenge, the thing is finding and disconnecting all the wiring harness connections and linkages to transmission and throttle and hoses that go to the engine from the fuel system and cooling system.

Jul 11, 2012 | Toyota Cars & Trucks

1 Answer

How do i pull the motor and put the new motor in on an 2001 chevrolet 1500 5.3l v8?

Removing and replacing an engine from a Silverado is not easily answered in one answer, but.....

1. Disconnect every electric component to the engine, starting with the battery.
2. Disconnect the cooling system, inlet, outlet, and any other cooling attachments to the engine.
3. Disconnect any accessories that connect to the engine, and drain the oil.
4. Disconnect the Exhaust system.
5. Disconnect the Fuel lines, oil lines, throttle cable, and any other lines that may be connected to the engine.
6. Hook up the Cherry picker (engine hoist), to the engine relieving the load from the transmission and the motor mounts.
7. Loosen the motor mounts all the way around, leaving one hanging on for safety.
8. Disconnect the engine from the Transmission.
9. Rock the engine back and forth, while lifting the cherry picker up.
10. Engine should be out of the car at this point.

To install a new engine, you are going to need to remember where everything went, and which bolts go where, from your engine removal.

1. Reverse every step above to install new engine.
2. Remember to check out every thing while you have the engine out. (Good opportunity:)
3. Have all of the lines, hoses, plugs, and cables out of the way and taped off for organization.
4. Put the new engine in the engine bay, and push it back into the Transmission. Turn the wheels of the truck to rotate the output shaft if the engine will not go all of the way in.
5. Tighten up the Transmission bolts, and the motor mounts.
6. Hook up the electrical, oiling, cooling, AC, throttle, etc.
7. Double check everything for efficiency.
8. Fill the fluids, cooling, oil, etc.
9. firing order and correct plug placement, and you should be ready to try to fire it up.
10. Timing, and other procedures can be carried out to tune the car.

Good luck :)


Oct 06, 2010 | 2001 Chevrolet Silverado 1500

1 Answer


Removal procedures :
1. Remove the rear seat cushion
2. To reduce the internal pressure of the fuel lines and hoses, first start the engine and then disconnect the electrical fuel pump connector. Be sure to reduce the fuel pressure before disconnecting the fuel main pipe and hose otherwise fuel will spill out.
3. Disconnect the battery cable from the negative terminal of the battery.
4. Remove the high pressure hose and fuel return hose.
5. Remove the fuel pump assembly.
Installation procedure is the reverse order of the removal.


Jun 07, 2010 | Hyundai Motor 1996 Elantra

3 Answers

2001 dodge stratus r/t engine code p0455 evac... what does this mean or how can i fix this essuie??

Or maybe the recall on the fuel return line 2001 Dodge Stratus Recall Date: 10/27/2000 2001 Dodge Stratus Component: FUEL SYSTEM, GASOLINE:DELIVERY:HOSES, LINES/PIPING, AND FITTINGS Potential Units Affected: 13100

Apr 03, 2010 | 2001 Dodge Stratus

1 Answer

Trouble starting

you may have an air leak in the petrol line, probably where the fuel pump was changed.
the car won't srpay out petrol some time's but overnight the vacum in the fuel line ****'s air in & the system is not primed.
The only way you can check this is by priming the rail first thing in the morning by turning the ignition key to the point just before starting & you should hear the fuel pump run for about 4 second's then turn off the ignotion, wait for a few sec's & turn the key to same position, it will prime again.
Do that a few times & check for petrol leak's as the fuel will run back to the tank via a pressure valve, If you see a leak then you've found where the air is getting back in if there is no leaking but the engine start's then you will have to go over all the hose clip's in the petrol system.
If not that then get back to me !

Sep 21, 2009 | 1995 Dodge Ram

1 Answer

9-3 will not start

check for fuel flow find & diconect fuel suply inlet line to fuel rail turn engine over

Jun 29, 2009 | 2001 Saab 9-3

1 Answer

I want to replace the motor.In my 2001 Silhouette What's the procedure.

Removal & Installation

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system.
  3. Drain the engine oil.
  4. Relieve the fuel system pressure.
  5. Remove or disconnect the following:
    CAUTION Failure to remove the intermediate shaft from the steering gear may result in damage to the gear or intermediate shaft and may cause a loss of steering control.

    Negative battery cable Fuel injector sight shield Throttle body air inlet duct Cruise control cable Accelerator control cable Radiator hoses from the engine Heater hoses from the engine Engine mount struts Fuel lines from the fuel rail Engine wiring harness connectors Vacuum hoses Brake booster vacuum hose Automatic transaxle range selector cable Wiring harness grounds Catalytic converter three-way pipe from the right side exhaust manifold Front wheels Splash shields Stabilizer shaft links from the lower control arms Tie rod ends from the steering knuckles Lower ball joints from the steering knuckles Cooler lines and bracket from the transaxle A/C compressor bolts and position compressor aside Axles from the transaxle and secure them to the steering knuckle/struts
  6. Remove or disconnect the following:

    Intermediate shaft from the steering gear Frame bolts and make certain that an engine stand (such as J 39580) is aligned below the engine

    0900c1528024ce9d.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Use a engine stand to support the assembly during frame removal
    Engine to transaxle bolts and studs Engine flywheel to torque converter bolts Engine from the transaxle and place it on the engine stand

To install:

May 05, 2009 | 2001 Oldsmobile Silhouette

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

17 people viewed this question

Ask a Question

Usually answered in minutes!

Top Cars & Trucks Experts


Level 3 Expert

78257 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14405 Answers

Are you a Car and Truck Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides